---

yaml
---
r: 130222
b: refs/heads/master
c: cfb901b
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 5fb4523afbffae5a5cec4989ee4c9fbc3dbdef33
+refs/heads/master: cfb901bf84fe22eb86525e9fb20675b53fb0462a

trunk/Documentation/kbuild/kbuild.txt

@@ -3,7 +3,7 @@ Environment variables
 KCPPFLAGS
 --------------------------------------------------
 Additional options to pass when preprocessing. The preprocessing options
-will be used in all cases where kbuild do preprocessing including
+will be used in all cases where kbuild does preprocessing including
 building C files and assembler files.
 
 KAFLAGS
@@ -16,7 +16,7 @@ Additional options to the C compiler.
 
 KBUILD_VERBOSE
 --------------------------------------------------
-Set the kbuild verbosity. Can be assinged same values as "V=...".
+Set the kbuild verbosity. Can be assigned same values as "V=...".
 See make help for the full list.
 Setting "V=..." takes precedence over KBUILD_VERBOSE.
 
@@ -35,14 +35,14 @@ KBUILD_OUTPUT
 --------------------------------------------------
 Specify the output directory when building the kernel.
 The output directory can also be specificed using "O=...".
-Setting "O=..." takes precedence over KBUILD_OUTPUT
+Setting "O=..." takes precedence over KBUILD_OUTPUT.
 
 ARCH
 --------------------------------------------------
 Set ARCH to the architecture to be built.
 In most cases the name of the architecture is the same as the
 directory name found in the arch/ directory.
-But some architectures suach as x86 and sparc has aliases.
+But some architectures such as x86 and sparc have aliases.
 x86: i386 for 32 bit, x86_64 for 64 bit
 sparc: sparc for 32 bit, sparc64 for 64 bit
 
@@ -63,7 +63,7 @@ CF is often used on the command-line like this:
 INSTALL_PATH
 --------------------------------------------------
 INSTALL_PATH specifies where to place the updated kernel and system map
-images. Default is /boot, but you can set it to other values
+images. Default is /boot, but you can set it to other values.
 
 
 MODLIB
@@ -90,7 +90,7 @@ INSTALL_MOD_STRIP will used as the options to the strip command.
 
 INSTALL_FW_PATH
 --------------------------------------------------
-INSTALL_FW_PATH specify where to install the firmware blobs.
+INSTALL_FW_PATH specifies where to install the firmware blobs.
 The default value is:
 
     $(INSTALL_MOD_PATH)/lib/firmware
@@ -99,7 +99,7 @@ The value can be overridden in which case the default value is ignored.
 
 INSTALL_HDR_PATH
 --------------------------------------------------
-INSTALL_HDR_PATH specify where to install user space headers when
+INSTALL_HDR_PATH specifies where to install user space headers when
 executing "make headers_*".
 The default value is:
 
@@ -112,22 +112,23 @@ The value can be overridden in which case the default value is ignored.
 
 KBUILD_MODPOST_WARN
 --------------------------------------------------
-KBUILD_MODPOST_WARN can be set to avoid error out in case of undefined
-symbols in the final module linking stage.
+KBUILD_MODPOST_WARN can be set to avoid errors in case of undefined
+symbols in the final module linking stage. It changes such errors
+into warnings.
 
-KBUILD_MODPOST_FINAL
+KBUILD_MODPOST_NOFINAL
 --------------------------------------------------
 KBUILD_MODPOST_NOFINAL can be set to skip the final link of modules.
-This is solely usefull to speed up test compiles.
+This is solely useful to speed up test compiles.
 
 KBUILD_EXTRA_SYMBOLS
 --------------------------------------------------
-For modules use symbols from another modules.
+For modules that use symbols from other modules.
 See more details in modules.txt.
 
 ALLSOURCE_ARCHS
 --------------------------------------------------
-For tags/TAGS/cscope targets, you can specify more than one archs
-to be included in the databases, separated by blankspace. e.g.
+For tags/TAGS/cscope targets, you can specify more than one arch
+to be included in the databases, separated by blank space. E.g.:
 
     $ make ALLSOURCE_ARCHS="x86 mips arm" tags

trunk/Documentation/kernel-parameters.txt

@@ -577,9 +577,6 @@ and is between 256 and 4096 characters. It is defined in the file
 			a memory unit (amount[KMG]). See also
 			Documentation/kdump/kdump.txt for a example.
 
-	cs4232=		[HW,OSS]
-			Format: <io>,<irq>,<dma>,<dma2>,<mpuio>,<mpuirq>
-
 	cs89x0_dma=	[HW,NET]
 			Format: <dma>
 
@@ -732,10 +729,6 @@ and is between 256 and 4096 characters. It is defined in the file
 			Default value is 0.
 			Value can be changed at runtime via /selinux/enforce.
 
-	es1371=		[HW,OSS]
-			Format: <spdif>,[<nomix>,[<amplifier>]]
-			See also header of sound/oss/es1371.c.
-
 	ether=		[HW,NET] Ethernet cards parameters
 			This option is obsoleted by the "netdev=" option, which
 			has equivalent usage. See its documentation for details.

trunk/Documentation/networking/netconsole.txt

@@ -51,7 +51,8 @@ Built-in netconsole starts immediately after the TCP stack is
 initialized and attempts to bring up the supplied dev at the supplied
 address.
 
-The remote host can run either 'netcat -u -l -p <port>' or syslogd.
+The remote host can run either 'netcat -u -l -p <port>',
+'nc -l -u <port>' or syslogd.
 
 Dynamic reconfiguration:
 ========================

trunk/Documentation/sound/alsa/HD-Audio-Models.txt

@@ -349,6 +349,7 @@ STAC92HD73*
 STAC92HD83*
 ===========
   ref		Reference board
+  mic-ref	Reference board with power managment for ports
 
 STAC9872
 ========

trunk/Makefile

@@ -213,6 +213,10 @@ endif
 # Where to locate arch specific headers
 hdr-arch  := $(SRCARCH)
 
+ifeq ($(ARCH),m68knommu)
+       hdr-arch  := m68k
+endif
+
 KCONFIG_CONFIG	?= .config
 
 # SHELL used by kbuild
@@ -606,25 +610,20 @@ export	INSTALL_PATH ?= /boot
 MODLIB	= $(INSTALL_MOD_PATH)/lib/modules/$(KERNELRELEASE)
 export MODLIB
 
-strip-symbols := $(srctree)/scripts/strip-symbols \
-		 $(wildcard $(srctree)/arch/$(ARCH)/scripts/strip-symbols)
-
 #
-# INSTALL_MOD_STRIP, if defined, will cause modules to be stripped while
-# they get installed.  If INSTALL_MOD_STRIP is '1', then the default
-# options (see below) will be used.  Otherwise, INSTALL_MOD_STRIP will
-# be used as the option(s) to the objcopy command.
+#  INSTALL_MOD_STRIP, if defined, will cause modules to be
+#  stripped after they are installed.  If INSTALL_MOD_STRIP is '1', then
+#  the default option --strip-debug will be used.  Otherwise,
+#  INSTALL_MOD_STRIP will used as the options to the strip command.
+
 ifdef INSTALL_MOD_STRIP
 ifeq ($(INSTALL_MOD_STRIP),1)
-mod_strip_cmd = $(OBJCOPY) --strip-debug
-ifeq ($(CONFIG_KALLSYMS_ALL),$(CONFIG_KALLSYMS_STRIP_GENERATED))
-mod_strip_cmd += --wildcard $(addprefix --strip-symbols ,$(strip-symbols))
-endif
+mod_strip_cmd = $(STRIP) --strip-debug
 else
-mod_strip_cmd = $(OBJCOPY) $(INSTALL_MOD_STRIP)
+mod_strip_cmd = $(STRIP) $(INSTALL_MOD_STRIP)
 endif # INSTALL_MOD_STRIP=1
 else
-mod_strip_cmd = false
+mod_strip_cmd = true
 endif # INSTALL_MOD_STRIP
 export mod_strip_cmd
 
@@ -754,7 +753,6 @@ last_kallsyms := 2
 endif
 
 kallsyms.o := .tmp_kallsyms$(last_kallsyms).o
-kallsyms.h := $(wildcard include/config/kallsyms/*.h) $(wildcard include/config/kallsyms/*/*.h)
 
 define verify_kallsyms
 	$(Q)$(if $($(quiet)cmd_sysmap),                                      \
@@ -779,41 +777,24 @@ endef
 
 # Generate .S file with all kernel symbols
 quiet_cmd_kallsyms = KSYM    $@
-      cmd_kallsyms = { test $* -eq 0 || $(NM) -n $<; } \
-		     | $(KALLSYMS) $(if $(CONFIG_KALLSYMS_ALL),--all-symbols) >$@
+      cmd_kallsyms = $(NM) -n $< | $(KALLSYMS) \
+                     $(if $(CONFIG_KALLSYMS_ALL),--all-symbols) > $@
 
-quiet_cmd_kstrip = STRIP   $@
-      cmd_kstrip = $(OBJCOPY) --wildcard $(addprefix --strip$(if $(CONFIG_RELOCATABLE),-unneeded)-symbols ,$(filter %/scripts/strip-symbols,$^)) $< $@
-
-$(foreach n,0 1 2 3,.tmp_kallsyms$(n).o): KBUILD_AFLAGS += -Wa,--strip-local-absolute
-$(foreach n,0 1 2 3,.tmp_kallsyms$(n).o): %.o: %.S scripts FORCE
+.tmp_kallsyms1.o .tmp_kallsyms2.o .tmp_kallsyms3.o: %.o: %.S scripts FORCE
 	$(call if_changed_dep,as_o_S)
 
-ifeq ($(CONFIG_KALLSYMS_STRIP_GENERATED),y)
-strip-ext := .stripped
-endif
-
-.tmp_kallsyms%.S: .tmp_vmlinux%$(strip-ext) $(KALLSYMS) $(kallsyms.h)
+.tmp_kallsyms%.S: .tmp_vmlinux% $(KALLSYMS)
 	$(call cmd,kallsyms)
 
-# make -jN seems to have problems with intermediate files, see bug #3330.
-.SECONDARY: $(foreach n,1 2 3,.tmp_vmlinux$(n).stripped)
-.tmp_vmlinux%.stripped: .tmp_vmlinux% $(strip-symbols) $(kallsyms.h)
-	$(call cmd,kstrip)
-
-ifneq ($(CONFIG_DEBUG_INFO),y)
-.tmp_vmlinux%: LDFLAGS_vmlinux += -S
-endif
 # .tmp_vmlinux1 must be complete except kallsyms, so update vmlinux version
-.tmp_vmlinux%: $(vmlinux-lds) $(vmlinux-all) FORCE
-	$(if $(filter 1,$*),$(call if_changed_rule,ksym_ld),$(call if_changed,vmlinux__))
+.tmp_vmlinux1: $(vmlinux-lds) $(vmlinux-all) FORCE
+	$(call if_changed_rule,ksym_ld)
 
-.tmp_vmlinux0$(strip-ext):
-	$(Q)echo "placeholder" >$@
+.tmp_vmlinux2: $(vmlinux-lds) $(vmlinux-all) .tmp_kallsyms1.o FORCE
+	$(call if_changed,vmlinux__)
 
-.tmp_vmlinux1: .tmp_kallsyms0.o
-.tmp_vmlinux2: .tmp_kallsyms1.o
-.tmp_vmlinux3: .tmp_kallsyms2.o
+.tmp_vmlinux3: $(vmlinux-lds) $(vmlinux-all) .tmp_kallsyms2.o FORCE
+	$(call if_changed,vmlinux__)
 
 # Needs to visit scripts/ before $(KALLSYMS) can be used.
 $(KALLSYMS): scripts ;