Merge remote-tracking branch 'regulator/topic/max8997' into regulator…

…-next

Documentation/devicetree/bindings/regulator/max8997-regulator.txt

@@ -0,0 +1,146 @@
+* Maxim MAX8997 Voltage and Current Regulator
+
+The Maxim MAX8997 is a multi-function device which includes volatage and
+current regulators, rtc, charger controller and other sub-blocks. It is
+interfaced to the host controller using a i2c interface. Each sub-block is
+addressed by the host system using different i2c slave address. This document
+describes the bindings for 'pmic' sub-block of max8997.
+
+Required properties:
+- compatible: Should be "maxim,max8997-pmic".
+- reg: Specifies the i2c slave address of the pmic block. It should be 0x66.
+
+- max8997,pmic-buck1-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+  units for buck1 when changing voltage using gpio dvs. Refer to [1] below
+  for additional information.
+
+- max8997,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+  units for buck2 when changing voltage using gpio dvs. Refer to [1] below
+  for additional information.
+
+- max8997,pmic-buck5-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+  units for buck5 when changing voltage using gpio dvs. Refer to [1] below
+  for additional information.
+
+[1] If none of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional
+    property is specified, the 'max8997,pmic-buck[1/2/5]-dvs-voltage'
+    property should specify atleast one voltage level (which would be a
+    safe operating voltage).
+
+    If either of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional
+    property is specified, then all the eigth voltage values for the
+    'max8997,pmic-buck[1/2/5]-dvs-voltage' should be specified.
+
+Optional properties:
+- interrupt-parent: Specifies the phandle of the interrupt controller to which
+  the interrupts from max8997 are delivered to.
+- interrupts: Interrupt specifiers for two interrupt sources.
+  - First interrupt specifier is for 'irq1' interrupt.
+  - Second interrupt specifier is for 'alert' interrupt.
+- max8997,pmic-buck1-uses-gpio-dvs: 'buck1' can be controlled by gpio dvs.
+- max8997,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs.
+- max8997,pmic-buck5-uses-gpio-dvs: 'buck5' can be controlled by gpio dvs.
+
+Additional properties required if either of the optional properties are used:
+- max8997,pmic-ignore-gpiodvs-side-effect: When GPIO-DVS mode is used for
+  multiple bucks, changing the voltage value of one of the bucks may affect
+  that of another buck, which is the side effect of the change (set_voltage).
+  Use this property to ignore such side effects and change the voltage.
+
+- max8997,pmic-buck125-default-dvs-idx: Default voltage setting selected from
+  the possible 8 options selectable by the dvs gpios. The value of this
+  property should be between 0 and 7. If not specified or if out of range, the
+  default value of this property is set to 0.
+
+- max8997,pmic-buck125-dvs-gpios: GPIO specifiers for three host gpio's used
+  for dvs. The format of the gpio specifier depends in the gpio controller.
+
+Regulators: The regulators of max8997 that have to be instantiated should be
+included in a sub-node named 'regulators'. Regulator nodes included in this
+sub-node should be of the format as listed below.
+
+	regulator_name {
+		standard regulator bindings here
+	};
+
+The following are the names of the regulators that the max8997 pmic block
+supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
+as per the datasheet of max8997.
+
+	- LDOn
+		  - valid values for n are 1 to 18 and 21
+		  - Example: LDO0, LD01, LDO2, LDO21
+	- BUCKn
+		  - valid values for n are 1 to 7.
+		  - Example: BUCK1, BUCK2, BUCK3, BUCK7
+
+	- ENVICHG: Battery Charging Current Monitor Output. This is a fixed
+		   voltage type regulator
+
+	- ESAFEOUT1: (ldo19)
+	- ESAFEOUT2: (ld020)
+
+	- CHARGER_CV: main battery charger voltage control
+	- CHARGER: main battery charger current control
+	- CHARGER_TOPOFF: end of charge current threshold level
+
+The bindings inside the regulator nodes use the standard regulator bindings
+which are documented elsewhere.
+
+Example:
+
+	max8997_pmic@66 {
+		compatible = "maxim,max8997-pmic";
+		interrupt-parent = <&wakeup_eint>;
+		reg = <0x66>;
+		interrupts = <4 0>, <3 0>;
+
+		max8997,pmic-buck1-uses-gpio-dvs;
+		max8997,pmic-buck2-uses-gpio-dvs;
+		max8997,pmic-buck5-uses-gpio-dvs;
+
+		max8997,pmic-ignore-gpiodvs-side-effect;
+		max8997,pmic-buck125-default-dvs-idx = <0>;
+
+		max8997,pmic-buck125-dvs-gpios = <&gpx0 0 1 0 0>, /* SET1 */
+						 <&gpx0 1 1 0 0>, /* SET2 */
+						 <&gpx0 2 1 0 0>; /* SET3 */
+
+		max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
+						 <1250000>, <1200000>,
+						 <1150000>, <1100000>,
+						 <1000000>, <950000>;
+
+		max8997,pmic-buck2-dvs-voltage = <1100000>, <1100000>,
+						 <1100000>, <1100000>,
+						 <1000000>, <1000000>,
+						 <1000000>, <1000000>;
+
+		max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>,
+						 <1200000>, <1200000>,
+						 <1200000>, <1200000>,
+						 <1200000>, <1200000>;
+
+		regulators {
+			ldo1_reg: LDO1 {
+				regulator-name = "VDD_ABB_3.3V";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "VDD_ALIVE_1.1V";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "VDD_ARM_1.2V";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};

drivers/mfd/max8997.c

@@ -21,8 +21,10 @@
  * This driver is based on max8998.c
  */
 
+#include <linux/err.h>
 #include <linux/slab.h>
 #include <linux/i2c.h>
+#include <linux/of_irq.h>
 #include <linux/interrupt.h>
 #include <linux/pm_runtime.h>
 #include <linux/module.h>
@@ -47,6 +49,13 @@ static struct mfd_cell max8997_devs[] = {
 	{ .name = "max8997-led", .id = 2 },
 };
 
+#ifdef CONFIG_OF
+static struct of_device_id __devinitdata max8997_pmic_dt_match[] = {
+	{ .compatible = "maxim,max8997-pmic", .data = TYPE_MAX8997 },
+	{},
+};
+#endif
+
 int max8997_read_reg(struct i2c_client *i2c, u8 reg, u8 *dest)
 {
 	struct max8997_dev *max8997 = i2c_get_clientdata(i2c);
@@ -123,6 +132,58 @@ int max8997_update_reg(struct i2c_client *i2c, u8 reg, u8 val, u8 mask)
 }
 EXPORT_SYMBOL_GPL(max8997_update_reg);
 
+#ifdef CONFIG_OF
+/*
+ * Only the common platform data elements for max8997 are parsed here from the
+ * device tree. Other sub-modules of max8997 such as pmic, rtc and others have
+ * to parse their own platform data elements from device tree.
+ *
+ * The max8997 platform data structure is instantiated here and the drivers for
+ * the sub-modules need not instantiate another instance while parsing their
+ * platform data.
+ */
+static struct max8997_platform_data *max8997_i2c_parse_dt_pdata(
+					struct device *dev)
+{
+	struct max8997_platform_data *pd;
+
+	pd = devm_kzalloc(dev, sizeof(*pd), GFP_KERNEL);
+	if (!pd) {
+		dev_err(dev, "could not allocate memory for pdata\n");
+		return ERR_PTR(-ENOMEM);
+	}
+
+	pd->ono = irq_of_parse_and_map(dev->of_node, 1);
+
+	/*
+	 * ToDo: the 'wakeup' member in the platform data is more of a linux
+	 * specfic information. Hence, there is no binding for that yet and
+	 * not parsed here.
+	 */
+
+	return pd;
+}
+#else
+static struct max8997_platform_data *max8997_i2c_parse_dt_pdata(
+					struct device *dev)
+{
+	return 0;
+}
+#endif
+
+static inline int max8997_i2c_get_driver_data(struct i2c_client *i2c,
+						const struct i2c_device_id *id)
+{
+#ifdef CONFIG_OF
+	if (i2c->dev.of_node) {
+		const struct of_device_id *match;
+		match = of_match_node(max8997_pmic_dt_match, i2c->dev.of_node);
+		return (int)match->data;
+	}
+#endif
+	return (int)id->driver_data;
+}
+
 static int max8997_i2c_probe(struct i2c_client *i2c,
 			    const struct i2c_device_id *id)
 {
@@ -137,12 +198,21 @@ static int max8997_i2c_probe(struct i2c_client *i2c,
 	i2c_set_clientdata(i2c, max8997);
 	max8997->dev = &i2c->dev;
 	max8997->i2c = i2c;
-	max8997->type = id->driver_data;
+	max8997->type = max8997_i2c_get_driver_data(i2c, id);
 	max8997->irq = i2c->irq;
 
+	if (max8997->dev->of_node) {
+		pdata = max8997_i2c_parse_dt_pdata(max8997->dev);
+		if (IS_ERR(pdata)) {
+			ret = PTR_ERR(pdata);
+			goto err;
+		}
+	}
+
 	if (!pdata)
 		goto err;
 
+	max8997->pdata = pdata;
 	max8997->ono = pdata->ono;
 
 	mutex_init(&max8997->iolock);
@@ -434,6 +504,7 @@ static struct i2c_driver max8997_i2c_driver = {
 		   .name = "max8997",
 		   .owner = THIS_MODULE,
 		   .pm = &max8997_pm,
+		   .of_match_table = of_match_ptr(max8997_pmic_dt_match),
 	},
 	.probe = max8997_i2c_probe,
 	.remove = max8997_i2c_remove,