pinctrl/coh901: use generic pinconf enums and parameters

Adjust the COH 901 driver to use the standard enums for
biasing and driving pins, alter signature of config function
to suit the framework.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

drivers/pinctrl/pinctrl-coh901.c

@@ -25,36 +25,6 @@
 #include <linux/pinctrl/consumer.h>
 #include <mach/gpio-u300.h>
 
-/*
- * Bias modes for U300 GPIOs
- *
- * GPIO_U300_CONFIG_BIAS_UNKNOWN: this bias mode is not known to us
- * GPIO_U300_CONFIG_BIAS_FLOAT: no specific bias, the GPIO will float or state
- *	is not controlled by software
- * GPIO_U300_CONFIG_BIAS_PULL_UP: the GPIO will be pulled up (usually with high
- *	impedance to VDD)
- */
-#define GPIO_U300_CONFIG_BIAS_UNKNOWN	0x1000
-#define GPIO_U300_CONFIG_BIAS_FLOAT	0x1001
-#define GPIO_U300_CONFIG_BIAS_PULL_UP	0x1002
-
-/*
- * Drive modes for U300 GPIOs (output)
- *
- * GPIO_U300_CONFIG_DRIVE_PUSH_PULL: the GPIO will be driven actively high and
- *	low, this is the most typical case and is typically achieved with two
- *	active transistors on the output
- * GPIO_U300_CONFIG_DRIVE_OPEN_DRAIN: the GPIO will be driven with open drain
- *	(open collector) which means it is usually wired with other output
- *	ports which are then pulled up with an external resistor
- * GPIO_U300_CONFIG_DRIVE_OPEN_SOURCE: the GPIO will be driven with open drain
- *	(open emitter) which is the same as open drain mutatis mutandis but
- *	pulled to ground
- */
-#define GPIO_U300_CONFIG_DRIVE_PUSH_PULL	0x2000
-#define GPIO_U300_CONFIG_DRIVE_OPEN_DRAIN	0x2001
-#define GPIO_U300_CONFIG_DRIVE_OPEN_SOURCE	0x2002
-
 /*
  * Register definitions for COH 901 335 variant
  */
@@ -181,12 +151,12 @@ struct u300_gpio_confdata {
 #define BS365_GPIO_NUM_PORTS 5
 
 #define U300_FLOATING_INPUT { \
-	.bias_mode = GPIO_U300_CONFIG_BIAS_FLOAT, \
+	.bias_mode = PIN_CONFIG_BIAS_HIGH_IMPEDANCE, \
 	.output = false, \
 }
 
 #define U300_PULL_UP_INPUT { \
-	.bias_mode = GPIO_U300_CONFIG_BIAS_PULL_UP, \
+	.bias_mode = PIN_CONFIG_BIAS_PULL_UP, \
 	.output = false, \
 }
 
@@ -449,40 +419,40 @@ static int u300_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
 }
 
 static int u300_gpio_config(struct gpio_chip *chip, unsigned offset,
-		     u16 param, unsigned long *data)
+			    enum pin_config_param param, unsigned long data)
 {
 	struct u300_gpio *gpio = to_u300_gpio(chip);
 	unsigned long flags;
 	u32 val;
 
 	local_irq_save(flags);
 	switch (param) {
-	case GPIO_U300_CONFIG_BIAS_UNKNOWN:
-	case GPIO_U300_CONFIG_BIAS_FLOAT:
+	case PIN_CONFIG_BIAS_DISABLE:
+	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
 		val = readl(U300_PIN_REG(offset, per));
 		writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, per));
 		break;
-	case GPIO_U300_CONFIG_BIAS_PULL_UP:
+	case PIN_CONFIG_BIAS_PULL_UP:
 		val = readl(U300_PIN_REG(offset, per));
 		writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, per));
 		break;
-	case GPIO_U300_CONFIG_DRIVE_PUSH_PULL:
+	case PIN_CONFIG_DRIVE_PUSH_PULL:
 		val = readl(U300_PIN_REG(offset, pcr));
 		val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
 			 << ((offset & 0x07) << 1));
 		val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL
 			<< ((offset & 0x07) << 1));
 		writel(val, U300_PIN_REG(offset, pcr));
 		break;
-	case GPIO_U300_CONFIG_DRIVE_OPEN_DRAIN:
+	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
 		val = readl(U300_PIN_REG(offset, pcr));
 		val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
 			 << ((offset & 0x07) << 1));
 		val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN
 			<< ((offset & 0x07) << 1));
 		writel(val, U300_PIN_REG(offset, pcr));
 		break;
-	case GPIO_U300_CONFIG_DRIVE_OPEN_SOURCE:
+	case PIN_CONFIG_DRIVE_OPEN_SOURCE:
 		val = readl(U300_PIN_REG(offset, pcr));
 		val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
 			 << ((offset & 0x07) << 1));
@@ -651,12 +621,12 @@ static void __init u300_gpio_init_pin(struct u300_gpio *gpio,
 
 		/* Deactivate bias mode for output */
 		u300_gpio_config(&gpio->chip, offset,
-				 GPIO_U300_CONFIG_BIAS_FLOAT,
-				 NULL);
+				 PIN_CONFIG_BIAS_HIGH_IMPEDANCE,
+				 0);
 
 		/* Set drive mode for output */
 		u300_gpio_config(&gpio->chip, offset,
-				 GPIO_U300_CONFIG_DRIVE_PUSH_PULL, NULL);
+				 PIN_CONFIG_DRIVE_PUSH_PULL, 0);
 
 		dev_dbg(gpio->dev, "set up pin %d as output, value: %d\n",
 			offset, conf->outval);
@@ -667,7 +637,7 @@ static void __init u300_gpio_init_pin(struct u300_gpio *gpio,
 		u300_gpio_set(&gpio->chip, offset, 0);
 
 		/* Set bias mode for input */
-		u300_gpio_config(&gpio->chip, offset, conf->bias_mode, NULL);
+		u300_gpio_config(&gpio->chip, offset, conf->bias_mode, 0);
 
 		dev_dbg(gpio->dev, "set up pin %d as input, bias: %04x\n",
 			offset, conf->bias_mode);