---

yaml
---
r: 334359
b: refs/heads/master
c: 47dbec5
h: refs/heads/master
i:
  334357: 8495030
  334355: 6ec407d
  334351: 46d6a8d
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: cba8d1cb6608bba49803ddceef1ff889aa2ed316
+refs/heads/master: 47dbec59c37ab02946a6db7ac30c3bf6ca02630c

trunk/Documentation/DocBook/networking.tmpl

@@ -56,7 +56,7 @@
 !Enet/core/filter.c
      </sect1>
      <sect1><title>Generic Network Statistics</title>
-!Iinclude/uapi/linux/gen_stats.h
+!Iinclude/linux/gen_stats.h
 !Enet/core/gen_stats.c
 !Enet/core/gen_estimator.c
      </sect1>
@@ -80,7 +80,7 @@
 !Enet/wimax/op-rfkill.c
 !Enet/wimax/stack.c
 !Iinclude/net/wimax.h
-!Iinclude/uapi/linux/wimax.h
+!Iinclude/linux/wimax.h
      </sect1>
   </chapter>
 

trunk/Documentation/IPMI.txt

@@ -42,7 +42,13 @@ The driver interface depends on your hardware.  If your system
 properly provides the SMBIOS info for IPMI, the driver will detect it
 and just work.  If you have a board with a standard interface (These
 will generally be either "KCS", "SMIC", or "BT", consult your hardware
-manual), choose the 'IPMI SI handler' option.
+manual), choose the 'IPMI SI handler' option.  A driver also exists
+for direct I2C access to the IPMI management controller.  Some boards
+support this, but it is unknown if it will work on every board.  For
+this, choose 'IPMI SMBus handler', but be ready to try to do some
+figuring to see if it will work on your system if the SMBIOS/APCI
+information is wrong or not present.  It is fairly safe to have both
+these enabled and let the drivers auto-detect what is present.
 
 You should generally enable ACPI on your system, as systems with IPMI
 can have ACPI tables describing them.
@@ -52,7 +58,8 @@ their job correctly, the IPMI controller should be automatically
 detected (via ACPI or SMBIOS tables) and should just work.  Sadly,
 many boards do not have this information.  The driver attempts
 standard defaults, but they may not work.  If you fall into this
-situation, you need to read the section below named 'The SI Driver'.
+situation, you need to read the section below named 'The SI Driver' or
+"The SMBus Driver" on how to hand-configure your system.
 
 IPMI defines a standard watchdog timer.  You can enable this with the
 'IPMI Watchdog Timer' config option.  If you compile the driver into
@@ -97,7 +104,12 @@ driver, each open file for this device ties in to the message handler
 as an IPMI user.
 
 ipmi_si - A driver for various system interfaces.  This supports KCS,
-SMIC, and BT interfaces.
+SMIC, and BT interfaces.  Unless you have an SMBus interface or your
+own custom interface, you probably need to use this.
+
+ipmi_smb - A driver for accessing BMCs on the SMBus. It uses the
+I2C kernel driver's SMBus interfaces to send and receive IPMI messages
+over the SMBus.
 
 ipmi_watchdog - IPMI requires systems to have a very capable watchdog
 timer.  This driver implements the standard Linux watchdog timer
@@ -470,6 +482,53 @@ for specifying an interface.  Note that when removing an interface,
 only the first three parameters (si type, address type, and address)
 are used for the comparison.  Any options are ignored for removing.
 
+The SMBus Driver
+----------------
+
+The SMBus driver allows up to 4 SMBus devices to be configured in the
+system.  By default, the driver will register any SMBus interfaces it finds
+in the I2C address range of 0x20 to 0x4f on any adapter.  You can change this
+at module load time (for a module) with:
+
+  modprobe ipmi_smb.o
+	addr=<adapter1>,<i2caddr1>[,<adapter2>,<i2caddr2>[,...]]
+	dbg=<flags1>,<flags2>...
+	[defaultprobe=1] [dbg_probe=1]
+
+The addresses are specified in pairs, the first is the adapter ID and the
+second is the I2C address on that adapter.
+
+The debug flags are bit flags for each BMC found, they are:
+IPMI messages: 1, driver state: 2, timing: 4, I2C probe: 8
+
+Setting smb_defaultprobe to zero disabled the default probing of SMBus
+interfaces at address range 0x20 to 0x4f.  This means that only the
+BMCs specified on the smb_addr line will be detected.
+
+Setting smb_dbg_probe to 1 will enable debugging of the probing and
+detection process for BMCs on the SMBusses.
+
+Discovering the IPMI compliant BMC on the SMBus can cause devices
+on the I2C bus to fail. The SMBus driver writes a "Get Device ID" IPMI
+message as a block write to the I2C bus and waits for a response.
+This action can be detrimental to some I2C devices. It is highly recommended
+that the known I2c address be given to the SMBus driver in the smb_addr
+parameter. The default address range will not be used when a smb_addr
+parameter is provided.
+
+When compiled into the kernel, the addresses can be specified on the
+kernel command line as:
+
+  ipmb_smb.addr=<adapter1>,<i2caddr1>[,<adapter2>,<i2caddr2>[,...]]
+	ipmi_smb.dbg=<flags1>,<flags2>...
+	ipmi_smb.defaultprobe=0 ipmi_smb.dbg_probe=1
+
+These are the same options as on the module command line.
+
+Note that you might need some I2C changes if CONFIG_IPMI_PANIC_EVENT
+is enabled along with this, so the I2C driver knows to run to
+completion during sending a panic event.
+
 
 Other Pieces
 ------------

trunk/MAINTAINERS

@@ -4372,7 +4372,7 @@ F:	Documentation/scsi/53c700.txt
 F:	drivers/scsi/53c700*
 
 LED SUBSYSTEM
-M:	Bryan Wu <cooloney@gmail.com>
+M:	Bryan Wu <bryan.wu@canonical.com>
 M:	Richard Purdie <rpurdie@rpsys.net>
 L:	linux-leds@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds.git

trunk/arch/arm/kernel/entry-common.S

@@ -88,9 +88,9 @@ ENTRY(ret_from_fork)
 	bl	schedule_tail
 	cmp	r5, #0
 	movne	r0, r4
-	adrne	lr, BSYM(1f)
+	movne	lr, pc
 	movne	pc, r5
-1:	get_thread_info tsk
+	get_thread_info tsk
 	b	ret_slow_syscall
 ENDPROC(ret_from_fork)
 

trunk/arch/x86/Makefile

@@ -142,7 +142,7 @@ KBUILD_CFLAGS += $(call cc-option,-mno-avx,)
 KBUILD_CFLAGS += $(mflags-y)
 KBUILD_AFLAGS += $(mflags-y)
 
-archscripts: scripts_basic
+archscripts:
 	$(Q)$(MAKE) $(build)=arch/x86/tools relocs
 
 ###

trunk/drivers/Makefile

@@ -17,10 +17,6 @@ obj-$(CONFIG_PARISC)		+= parisc/
 obj-$(CONFIG_RAPIDIO)		+= rapidio/
 obj-y				+= video/
 obj-y				+= idle/
-
-# IPMI must come before ACPI in order to provide IPMI opregion support
-obj-$(CONFIG_IPMI_HANDLER)	+= char/ipmi/
-
 obj-$(CONFIG_ACPI)		+= acpi/
 obj-$(CONFIG_SFI)		+= sfi/
 # PnP must come after ACPI since it will eventually need to check if acpi

trunk/drivers/acpi/Makefile

@@ -47,10 +47,6 @@ acpi-y				+= video_detect.o
 endif
 
 # These are (potentially) separate modules
-
-# IPMI may be used by other drivers, so it has to initialise before them
-obj-$(CONFIG_ACPI_IPMI)		+= acpi_ipmi.o
-
 obj-$(CONFIG_ACPI_AC) 		+= ac.o
 obj-$(CONFIG_ACPI_BUTTON)	+= button.o
 obj-$(CONFIG_ACPI_FAN)		+= fan.o
@@ -74,5 +70,6 @@ processor-y			+= processor_idle.o processor_thermal.o
 processor-$(CONFIG_CPU_FREQ)	+= processor_perflib.o
 
 obj-$(CONFIG_ACPI_PROCESSOR_AGGREGATOR) += acpi_pad.o
+obj-$(CONFIG_ACPI_IPMI)		+= acpi_ipmi.o
 
 obj-$(CONFIG_ACPI_APEI)		+= apei/

trunk/drivers/char/Makefile

@@ -52,6 +52,7 @@ obj-$(CONFIG_TELCLOCK)		+= tlclk.o
 obj-$(CONFIG_MWAVE)		+= mwave/
 obj-$(CONFIG_AGP)		+= agp/
 obj-$(CONFIG_PCMCIA)		+= pcmcia/
+obj-$(CONFIG_IPMI_HANDLER)	+= ipmi/
 
 obj-$(CONFIG_HANGCHECK_TIMER)	+= hangcheck-timer.o
 obj-$(CONFIG_TCG_TPM)		+= tpm/

trunk/drivers/char/ipmi/ipmi_msghandler.c

@@ -1880,7 +1880,7 @@ int ipmi_request_supply_msgs(ipmi_user_t          user,
 			     struct ipmi_recv_msg *supplied_recv,
 			     int                  priority)
 {
-	unsigned char saddr = 0, lun = 0;
+	unsigned char saddr, lun;
 	int           rv;
 
 	if (!user)

trunk/drivers/char/ipmi/ipmi_si_intf.c

@@ -2424,38 +2424,6 @@ static void ipmi_pci_cleanup(struct smi_info *info)
 	pci_disable_device(pdev);
 }
 
-static int __devinit ipmi_pci_probe_regspacing(struct smi_info *info)
-{
-	if (info->si_type == SI_KCS) {
-		unsigned char	status;
-		int		regspacing;
-
-		info->io.regsize = DEFAULT_REGSIZE;
-		info->io.regshift = 0;
-		info->io_size = 2;
-		info->handlers = &kcs_smi_handlers;
-
-		/* detect 1, 4, 16byte spacing */
-		for (regspacing = DEFAULT_REGSPACING; regspacing <= 16;) {
-			info->io.regspacing = regspacing;
-			if (info->io_setup(info)) {
-				dev_err(info->dev,
-					"Could not setup I/O space\n");
-				return DEFAULT_REGSPACING;
-			}
-			/* write invalid cmd */
-			info->io.outputb(&info->io, 1, 0x10);
-			/* read status back */
-			status = info->io.inputb(&info->io, 1);
-			info->io_cleanup(info);
-			if (status)
-				return regspacing;
-			regspacing *= 4;
-		}
-	}
-	return DEFAULT_REGSPACING;
-}
-
 static int __devinit ipmi_pci_probe(struct pci_dev *pdev,
 				    const struct pci_device_id *ent)
 {
@@ -2508,8 +2476,8 @@ static int __devinit ipmi_pci_probe(struct pci_dev *pdev,
 	}
 	info->io.addr_data = pci_resource_start(pdev, 0);
 
-	info->io.regspacing = ipmi_pci_probe_regspacing(info);
-	info->io.regsize = DEFAULT_REGSIZE;
+	info->io.regspacing = DEFAULT_REGSPACING;
+	info->io.regsize = DEFAULT_REGSPACING;
 	info->io.regshift = 0;
 
 	info->irq = pdev->irq;

trunk/drivers/pinctrl/pinctrl-samsung.c

@@ -513,7 +513,7 @@ static int samsung_gpio_direction_output(struct gpio_chip *gc, unsigned offset,
  * Parse the pin names listed in the 'samsung,pins' property and convert it
  * into a list of gpio numbers are create a pin group from it.
  */
-static int __init samsung_pinctrl_parse_dt_pins(struct platform_device *pdev,
+static int __devinit samsung_pinctrl_parse_dt_pins(struct platform_device *pdev,
 			struct device_node *cfg_np, struct pinctrl_desc *pctl,
 			unsigned int **pin_list, unsigned int *npins)
 {
@@ -560,7 +560,7 @@ static int __init samsung_pinctrl_parse_dt_pins(struct platform_device *pdev,
  * from device node of the pin-controller. A pin group is formed with all
  * the pins listed in the "samsung,pins" property.
  */
-static int __init samsung_pinctrl_parse_dt(struct platform_device *pdev,
+static int __devinit samsung_pinctrl_parse_dt(struct platform_device *pdev,
 				struct samsung_pinctrl_drv_data *drvdata)
 {
 	struct device *dev = &pdev->dev;
@@ -655,7 +655,7 @@ static int __init samsung_pinctrl_parse_dt(struct platform_device *pdev,
 }
 
 /* register the pinctrl interface with the pinctrl subsystem */
-static int __init samsung_pinctrl_register(struct platform_device *pdev,
+static int __devinit samsung_pinctrl_register(struct platform_device *pdev,
 				struct samsung_pinctrl_drv_data *drvdata)
 {
 	struct pinctrl_desc *ctrldesc = &drvdata->pctl;
@@ -729,7 +729,7 @@ static int __init samsung_pinctrl_register(struct platform_device *pdev,
 }
 
 /* register the gpiolib interface with the gpiolib subsystem */
-static int __init samsung_gpiolib_register(struct platform_device *pdev,
+static int __devinit samsung_gpiolib_register(struct platform_device *pdev,
 				struct samsung_pinctrl_drv_data *drvdata)
 {
 	struct gpio_chip *gc;
@@ -762,7 +762,7 @@ static int __init samsung_gpiolib_register(struct platform_device *pdev,
 }
 
 /* unregister the gpiolib interface with the gpiolib subsystem */
-static int __init samsung_gpiolib_unregister(struct platform_device *pdev,
+static int __devinit samsung_gpiolib_unregister(struct platform_device *pdev,
 				struct samsung_pinctrl_drv_data *drvdata)
 {
 	int ret = gpiochip_remove(drvdata->gc);

trunk/drivers/thermal/Kconfig

@@ -22,7 +22,6 @@ config THERMAL_HWMON
 config CPU_THERMAL
 	bool "generic cpu cooling support"
 	depends on THERMAL && CPU_FREQ
-	select CPU_FREQ_TABLE
 	help
 	  This implements the generic cpu cooling mechanism through frequency
 	  reduction, cpu hotplug and any other ways of reducing temperature. An
@@ -51,7 +50,6 @@ config RCAR_THERMAL
 config EXYNOS_THERMAL
 	tristate "Temperature sensor on Samsung EXYNOS"
 	depends on (ARCH_EXYNOS4 || ARCH_EXYNOS5) && THERMAL
-	select CPU_FREQ_TABLE
 	help
 	  If you say yes here you get support for TMU (Thermal Managment
 	  Unit) on SAMSUNG EXYNOS series of SoC.

trunk/fs/proc/task_mmu.c

@@ -1158,7 +1158,6 @@ static int show_numa_map(struct seq_file *m, void *v, int is_pid)
 	struct vm_area_struct *vma = v;
 	struct numa_maps *md = &numa_priv->md;
 	struct file *file = vma->vm_file;
-	struct task_struct *task = proc_priv->task;
 	struct mm_struct *mm = vma->vm_mm;
 	struct mm_walk walk = {};
 	struct mempolicy *pol;
@@ -1178,11 +1177,9 @@ static int show_numa_map(struct seq_file *m, void *v, int is_pid)
 	walk.private = md;
 	walk.mm = mm;
 
-	task_lock(task);
-	pol = get_vma_policy(task, vma, vma->vm_start);
+	pol = get_vma_policy(proc_priv->task, vma, vma->vm_start);
 	mpol_to_str(buffer, sizeof(buffer), pol, 0);
 	mpol_cond_put(pol);
-	task_unlock(task);
 
 	seq_printf(m, "%08lx %s", vma->vm_start, buffer);
 
@@ -1192,7 +1189,7 @@ static int show_numa_map(struct seq_file *m, void *v, int is_pid)
 	} else if (vma->vm_start <= mm->brk && vma->vm_end >= mm->start_brk) {
 		seq_printf(m, " heap");
 	} else {
-		pid_t tid = vm_is_stack(task, vma, is_pid);
+		pid_t tid = vm_is_stack(proc_priv->task, vma, is_pid);
 		if (tid != 0) {
 			/*
 			 * Thread stack in /proc/PID/task/TID/maps or

trunk/mm/huge_memory.c

@@ -17,7 +17,6 @@
 #include <linux/khugepaged.h>
 #include <linux/freezer.h>
 #include <linux/mman.h>
-#include <linux/pagemap.h>
 #include <asm/tlb.h>
 #include <asm/pgalloc.h>
 #include "internal.h"

trunk/mm/mempolicy.c

@@ -1536,8 +1536,9 @@ asmlinkage long compat_sys_mbind(compat_ulong_t start, compat_ulong_t len,
  *
  * Returns effective policy for a VMA at specified address.
  * Falls back to @task or system default policy, as necessary.
- * Current or other task's task mempolicy and non-shared vma policies must be
- * protected by task_lock(task) by the caller.
+ * Current or other task's task mempolicy and non-shared vma policies
+ * are protected by the task's mmap_sem, which must be held for read by
+ * the caller.
  * Shared policies [those marked as MPOL_F_SHARED] require an extra reference
  * count--added by the get_policy() vm_op, as appropriate--to protect against
  * freeing by another task.  It is the caller's responsibility to free the

trunk/scripts/Makefile.fwinst

@@ -27,7 +27,7 @@ endif
 installed-mod-fw := $(addprefix $(INSTALL_FW_PATH)/,$(mod-fw))
 
 installed-fw := $(addprefix $(INSTALL_FW_PATH)/,$(fw-shipped-all))
-installed-fw-dirs := $(sort $(dir $(installed-fw))) $(INSTALL_FW_PATH)/./
+installed-fw-dirs := $(sort $(dir $(installed-fw))) $(INSTALL_FW_PATH)/.
 
 # Workaround for make < 3.81, where .SECONDEXPANSION doesn't work.
 PHONY += $(INSTALL_FW_PATH)/$$(%) install-all-dirs
@@ -42,7 +42,7 @@ quiet_cmd_install = INSTALL $(subst $(srctree)/,,$@)
 $(installed-fw-dirs):
 	$(call cmd,mkdir)
 
-$(installed-fw): $(INSTALL_FW_PATH)/%: $(obj)/% | $(INSTALL_FW_PATH)/$$(dir %)
+$(installed-fw): $(INSTALL_FW_PATH)/%: $(obj)/% | $$(dir $(INSTALL_FW_PATH)/%)
 	$(call cmd,install)
 
 PHONY +=  __fw_install __fw_modinst FORCE