Staging: batman-adv: Start new development cycle

Version 2010.1.0 of the extra kernel module was released and thus the
documentation should be updated and everything prepared for the the
upcoming patchset.

Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/staging/batman-adv/README

@@ -1,4 +1,4 @@
-[state: 12-06-2010]
+[state: 04-09-2010]
 
 BATMAN-ADV
 ----------
@@ -67,23 +67,29 @@ All  mesh  wide  settings  can be found in batman's own interface
 folder:
 
 #  ls  /sys/class/net/bat0/mesh/
-#  aggregate_ogm   originators        transtable_global  vis_mode
-#  orig_interval   transtable_local   vis_data
+#  aggregated_ogms  bonding  orig_interval  vis_mode
+
+
+There is a special folder for debugging informations:
+
+#  ls /sys/kernel/debug/batman_adv/bat0/
+#  originators  socket  transtable_global  transtable_local
+#  vis_data
 
 
 Some of the files contain all sort of status information  regard-
 ing  the  mesh  network.  For  example, you can view the table of
 originators (mesh participants) with:
 
-# cat /sys/class/net/bat0/mesh/originators
+# cat /sys/kernel/debug/batman_adv/bat0/originators
 
 Other files allow to change batman's behaviour to better fit your
 requirements.  For instance, you can check the current originator
 interval (value in milliseconds which determines how often batman
 sends its broadcast packets):
 
 # cat /sys/class/net/bat0/mesh/orig_interval
-# status: 1000
+# 1000
 
 and also change its value:
 
@@ -137,7 +143,7 @@ at least very similar) data.
 When  configured  as  server,  you can get a topology snapshot of
 your mesh:
 
-# cat /sys/class/net/bat0/mesh/vis_data
+# cat /sys/kernel/debug/batman_adv/bat0/vis_data
 
 This raw output is intended to be easily parsable and convertable
 with  other tools. Have a look at the batctl README if you want a
@@ -181,32 +187,25 @@ enabled when compiling the batman-adv module. When building  bat-
 man-adv  as  part of kernel, use "make menuconfig" and enable the
 option "B.A.T.M.A.N. debugging".
 
+Those additional  debug messages can be accessed  using a special
+file in debugfs
+
+# cat /sys/kernel/debug/batman_adv/bat0/log
+
 The additional debug output is by default disabled. It can be en-
-abled  either  at kernel modules load time or during run time. To
-enable debug output at module load time, add the module parameter
-debug=<value>.  <value> can take one of four values.
+abled  during run time. Following log_levels are defined:
 
 0 - All  debug  output  disabled
 1 - Enable messages related to routing / flooding / broadcasting
 2 - Enable route or hna added / changed / deleted
 3 - Enable all messages
 
-e.g.
-
-# modprobe batman-adv debug=2
-
-will load the module and enable debug messages for when routes or
-HNAs change.
-
-The debug output can also be changed at runtime  using  the  file
-/sys/module/batman-adv/parameters/debug. e.g.
-
-# echo 2 > /sys/module/batman-adv/parameters/debug
+The debug output can be changed at runtime  using  the  file
+/sys/class/net/bat0/mesh/log_level. e.g.
 
-enables debug messages for when routes or HNAs
+# echo 2 > /sys/class/net/bat0/mesh/log_level
 
-The  debug  output  is sent to the kernel logs. So try dmesg, lo-
-gread, etc to see the debug messages.
+will enable debug messages for when routes or HNAs change.
 
 
 BATCTL

drivers/staging/batman-adv/main.h

@@ -30,7 +30,7 @@
 #define DRIVER_DESC   "B.A.T.M.A.N. advanced"
 #define DRIVER_DEVICE "batman-adv"
 
-#define SOURCE_VERSION "maint"
+#define SOURCE_VERSION "next"
 
 
 /* B.A.T.M.A.N. parameters */