[SCSI] Remove some unused SCSI-related kernel config variables.

Remove the unused SCSI-related kernel config variables

	SCSI_NCR53C8XX_PROFILE_SUPPORT
	SCSI_NCR53C8XX_PROFILE
	53C700_IO_MAPPED
	AIC79XX_ENABLE_RD_STRM
	AIC7XXX_PROBE_EISA_VL

Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Documentation/scsi/ncr53c8xx.txt

@@ -562,11 +562,6 @@ if only one has a flaw for some SCSI feature, you can disable the
 support by the driver of this feature at linux start-up and enable
 this feature after boot-up only for devices that support it safely.
 
-CONFIG_SCSI_NCR53C8XX_PROFILE_SUPPORT  (default answer: n)
-    This option must be set for profiling information to be gathered 
-    and printed out through the proc file system. This features may 
-    impact performances.
-
 CONFIG_SCSI_NCR53C8XX_IOMAPPED       (default answer: n)
     Answer "y" if you suspect your mother board to not allow memory mapped I/O.
     May slow down performance a little.  This option is required by

drivers/scsi/Kconfig

@@ -1200,17 +1200,6 @@ config SCSI_NCR53C8XX_SYNC
 	  There is no safe option other than using good cabling, right
 	  terminations and SCSI conformant devices.
 
-config SCSI_NCR53C8XX_PROFILE
-	bool "enable profiling"
-	depends on SCSI_ZALON || SCSI_NCR_Q720
-	help
-	  This option allows you to enable profiling information gathering.
-	  These statistics are not very accurate due to the low frequency
-	  of the kernel clock (100 Hz on i386) and have performance impact
-	  on systems that use very fast devices.
-
-	  The normal answer therefore is N.
-
 config SCSI_NCR53C8XX_NO_DISCONNECT
 	bool "not allow targets to disconnect"
 	depends on (SCSI_ZALON || SCSI_NCR_Q720) && SCSI_NCR53C8XX_DEFAULT_TAGS=0
@@ -1340,11 +1329,6 @@ config SCSI_SIM710
 
 	  It currently supports Compaq EISA cards and NCR MCA cards
 
-config 53C700_IO_MAPPED
-	bool
-	depends on SCSI_SIM710
-	default y
-
 config SCSI_SYM53C416
 	tristate "Symbios 53c416 SCSI support"
 	depends on ISA && SCSI

drivers/scsi/aic7xxx/Kconfig.aic79xx

@@ -57,18 +57,6 @@ config AIC79XX_BUILD_FIRMWARE
 	or modify the assembler Makefile or the files it includes if your
 	build environment is different than that of the author.
 
-config AIC79XX_ENABLE_RD_STRM
-	bool "Enable Read Streaming for All Targets"
-	depends on SCSI_AIC79XX
-	default n
-	help
-	Read Streaming is a U320 protocol option that should enhance
-	performance.  Early U320 drive firmware actually performs slower
-	with read streaming enabled so it is disabled by default.  Read
-	Streaming can be configured in much the same way as tagged queueing
-	using the "rd_strm" command line option.  See
-	drivers/scsi/aic7xxx/README.aic79xx for details.
-
 config AIC79XX_DEBUG_ENABLE
 	bool "Compile in Debugging Code"
 	depends on SCSI_AIC79XX

drivers/scsi/aic7xxx/Kconfig.aic7xxx

@@ -50,16 +50,6 @@ config AIC7XXX_RESET_DELAY_MS
 
 	Default: 5000 (5 seconds)
 
-config AIC7XXX_PROBE_EISA_VL
-	bool "Probe for EISA and VL AIC7XXX Adapters"
-	depends on SCSI_AIC7XXX && EISA
-	help
-	Probe for EISA and VLB Aic7xxx controllers.  In many newer systems,
-	the invasive probes necessary to detect these controllers can cause
-	other devices to fail.  For this reason, the non-PCI probe code is
-	disabled by default.  The current value of this option can be "toggled"
-	via the no_probe kernel command line option.
-
 config AIC7XXX_BUILD_FIRMWARE
 	bool "Build Adapter Firmware with Kernel Build"
 	depends on SCSI_AIC7XXX && !PREVENT_FIRMWARE_BUILD