---

yaml
---
r: 288407
b: refs/heads/master
c: de3a49b
h: refs/heads/master
i:
  288405: bcd15cf
  288403: 22597e0
  288399: b604231
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: a10a854365503ad5e374b3cd48f06aa486df7211
+refs/heads/master: de3a49b8a44cb6b272450cef060385a83dc05d74

trunk/Documentation/devicetree/bindings/gpio/led.txt

@@ -7,9 +7,9 @@ Each LED is represented as a sub-node of the gpio-leds device.  Each
 node's name represents the name of the corresponding LED.
 
 LED sub-node properties:
-- gpios :  Should specify the LED's GPIO, see "gpios property" in
-  Documentation/devicetree/gpio.txt.  Active low LEDs should be
-  indicated using flags in the GPIO specifier.
+- gpios :  Should specify the LED's GPIO, see "Specifying GPIO information
+  for devices" in Documentation/devicetree/booting-without-of.txt.  Active
+  low LEDs should be indicated using flags in the GPIO specifier.
 - label :  (optional) The label for this LED.  If omitted, the label is
   taken from the node name (excluding the unit address).
 - linux,default-trigger :  (optional) This parameter, if present, is a

trunk/Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -30,7 +30,6 @@ national	National Semiconductor
 nintendo	Nintendo
 nvidia	NVIDIA
 nxp	NXP Semiconductors
-picochip	Picochip Ltd
 powervr	Imagination Technologies
 qcom	Qualcomm, Inc.
 ramtron	Ramtron International

trunk/Documentation/hwmon/jc42

@@ -7,29 +7,21 @@ Supported chips:
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
 	http://www.analog.com/static/imported-files/data_sheets/ADT7408.pdf
-  * Atmel AT30TS00
-    Prefix: 'at30ts00'
+  * IDT TSE2002B3, TS3000B3
+    Prefix: 'tse2002b3', 'ts3000b3'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
-	http://www.atmel.com/Images/doc8585.pdf
-  * IDT TSE2002B3, TSE2002GB2, TS3000B3, TS3000GB2
-    Prefix: 'tse2002', 'ts3000'
-    Addresses scanned: I2C 0x18 - 0x1f
-    Datasheets:
-	http://www.idt.com/sites/default/files/documents/IDT_TSE2002B3C_DST_20100512_120303152056.pdf
-	http://www.idt.com/sites/default/files/documents/IDT_TSE2002GB2A1_DST_20111107_120303145914.pdf
-	http://www.idt.com/sites/default/files/documents/IDT_TS3000B3A_DST_20101129_120303152013.pdf
-	http://www.idt.com/sites/default/files/documents/IDT_TS3000GB2A1_DST_20111104_120303151012.pdf
+	http://www.idt.com/products/getdoc.cfm?docid=18715691
+	http://www.idt.com/products/getdoc.cfm?docid=18715692
   * Maxim MAX6604
     Prefix: 'max6604'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
 	http://datasheets.maxim-ic.com/en/ds/MAX6604.pdf
-  * Microchip MCP9804, MCP9805, MCP98242, MCP98243, MCP9843
-    Prefixes: 'mcp9804', 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843'
+  * Microchip MCP9805, MCP98242, MCP98243, MCP9843
+    Prefixes: 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843'
     Addresses scanned: I2C 0x18 - 0x1f
     Datasheets:
-	http://ww1.microchip.com/downloads/en/DeviceDoc/22203C.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf
 	http://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf
@@ -56,12 +48,6 @@ Supported chips:
     Datasheets:
 	http://www.st.com/stonline/products/literature/ds/13447/stts424.pdf
 	http://www.st.com/stonline/products/literature/ds/13448/stts424e02.pdf
-  * ST Microelectronics STTS2002, STTS3000
-    Prefix: 'stts2002', 'stts3000'
-    Addresses scanned: I2C 0x18 - 0x1f
-    Datasheets:
-	http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00225278.pdf
-	http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATA_BRIEF/CD00270920.pdf
   * JEDEC JC 42.4 compliant temperature sensor chips
     Prefix: 'jc42'
     Addresses scanned: I2C 0x18 - 0x1f

trunk/Documentation/input/alps.txt

@@ -13,8 +13,7 @@ Detection
 
 All ALPS touchpads should respond to the "E6 report" command sequence:
 E8-E6-E6-E6-E9. An ALPS touchpad should respond with either 00-00-0A or
-00-00-64 if no buttons are pressed. The bits 0-2 of the first byte will be 1s
-if some buttons are pressed.
+00-00-64.
 
 If the E6 report is successful, the touchpad model is identified using the "E7
 report" sequence: E8-E7-E7-E7-E9. The response is the model signature and is

trunk/MAINTAINERS

@@ -962,7 +962,7 @@ F:	drivers/tty/serial/msm_serial.c
 F:	drivers/platform/msm/
 F:	drivers/*/pm8???-*
 F:	include/linux/mfd/pm8xxx/
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm.git
+T:	git git://codeaurora.org/quic/kernel/davidb/linux-msm.git
 S:	Maintained
 
 ARM/TOSA MACHINE SUPPORT

trunk/Makefile

@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 3
 SUBLEVEL = 0
-EXTRAVERSION = -rc7
+EXTRAVERSION = -rc6
 NAME = Saber-toothed Squirrel
 
 # *DOCUMENTATION*

trunk/arch/arm/Kconfig

@@ -1280,7 +1280,7 @@ config ARM_ERRATA_743622
 	depends on CPU_V7
 	help
 	  This option enables the workaround for the 743622 Cortex-A9
-	  (r2p*) erratum. Under very rare conditions, a faulty
+	  (r2p0..r2p2) erratum. Under very rare conditions, a faulty
 	  optimisation in the Cortex-A9 Store Buffer may lead to data
 	  corruption. This workaround sets a specific bit in the diagnostic
 	  register of the Cortex-A9 which disables the Store Buffer

trunk/arch/arm/boot/.gitignore

@@ -3,4 +3,3 @@ zImage
 xipImage
 bootpImage
 uImage
-*.dtb

trunk/arch/arm/include/asm/pmu.h

@@ -134,7 +134,7 @@ int __init armpmu_register(struct arm_pmu *armpmu, char *name, int type);
 
 u64 armpmu_event_update(struct perf_event *event,
 			struct hw_perf_event *hwc,
-			int idx);
+			int idx, int overflow);
 
 int armpmu_event_set_period(struct perf_event *event,
 			    struct hw_perf_event *hwc,

trunk/arch/arm/kernel/ecard.c

@@ -242,7 +242,6 @@ static void ecard_init_pgtables(struct mm_struct *mm)
 
 	memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (EASI_SIZE / PGDIR_SIZE));
 
-	vma.vm_flags = VM_EXEC;
 	vma.vm_mm = mm;
 
 	flush_tlb_range(&vma, IO_START, IO_START + IO_SIZE);

trunk/arch/arm/kernel/perf_event.c

@@ -180,7 +180,7 @@ armpmu_event_set_period(struct perf_event *event,
 u64
 armpmu_event_update(struct perf_event *event,
 		    struct hw_perf_event *hwc,
-		    int idx)
+		    int idx, int overflow)
 {
 	struct arm_pmu *armpmu = to_arm_pmu(event->pmu);
 	u64 delta, prev_raw_count, new_raw_count;
@@ -193,7 +193,13 @@ armpmu_event_update(struct perf_event *event,
 			     new_raw_count) != prev_raw_count)
 		goto again;
 
-	delta = (new_raw_count - prev_raw_count) & armpmu->max_period;
+	new_raw_count &= armpmu->max_period;
+	prev_raw_count &= armpmu->max_period;
+
+	if (overflow)
+		delta = armpmu->max_period - prev_raw_count + new_raw_count + 1;
+	else
+		delta = new_raw_count - prev_raw_count;
 
 	local64_add(delta, &event->count);
 	local64_sub(delta, &hwc->period_left);
@@ -210,7 +216,7 @@ armpmu_read(struct perf_event *event)
 	if (hwc->idx < 0)
 		return;
 
-	armpmu_event_update(event, hwc, hwc->idx);
+	armpmu_event_update(event, hwc, hwc->idx, 0);
 }
 
 static void
@@ -226,7 +232,7 @@ armpmu_stop(struct perf_event *event, int flags)
 	if (!(hwc->state & PERF_HES_STOPPED)) {
 		armpmu->disable(hwc, hwc->idx);
 		barrier(); /* why? */
-		armpmu_event_update(event, hwc, hwc->idx);
+		armpmu_event_update(event, hwc, hwc->idx, 0);
 		hwc->state |= PERF_HES_STOPPED | PERF_HES_UPTODATE;
 	}
 }
@@ -512,13 +518,7 @@ __hw_perf_event_init(struct perf_event *event)
 	hwc->config_base	    |= (unsigned long)mapping;
 
 	if (!hwc->sample_period) {
-		/*
-		 * For non-sampling runs, limit the sample_period to half
-		 * of the counter width. That way, the new counter value
-		 * is far less likely to overtake the previous one unless
-		 * you have some serious IRQ latency issues.
-		 */
-		hwc->sample_period  = armpmu->max_period >> 1;
+		hwc->sample_period  = armpmu->max_period;
 		hwc->last_period    = hwc->sample_period;
 		local64_set(&hwc->period_left, hwc->sample_period);
 	}
@@ -679,28 +679,6 @@ static void __init cpu_pmu_init(struct arm_pmu *armpmu)
 	armpmu->type = ARM_PMU_DEVICE_CPU;
 }
 
-/*
- * PMU hardware loses all context when a CPU goes offline.
- * When a CPU is hotplugged back in, since some hardware registers are
- * UNKNOWN at reset, the PMU must be explicitly reset to avoid reading
- * junk values out of them.
- */
-static int __cpuinit pmu_cpu_notify(struct notifier_block *b,
-					unsigned long action, void *hcpu)
-{
-	if ((action & ~CPU_TASKS_FROZEN) != CPU_STARTING)
-		return NOTIFY_DONE;
-
-	if (cpu_pmu && cpu_pmu->reset)
-		cpu_pmu->reset(NULL);
-
-	return NOTIFY_OK;
-}
-
-static struct notifier_block __cpuinitdata pmu_cpu_notifier = {
-	.notifier_call = pmu_cpu_notify,
-};
-
 /*
  * CPU PMU identification and registration.
  */
@@ -752,7 +730,6 @@ init_hw_perf_events(void)
 		pr_info("enabled with %s PMU driver, %d counters available\n",
 			cpu_pmu->name, cpu_pmu->num_events);
 		cpu_pmu_init(cpu_pmu);
-		register_cpu_notifier(&pmu_cpu_notifier);
 		armpmu_register(cpu_pmu, "cpu", PERF_TYPE_RAW);
 	} else {
 		pr_info("no hardware support available\n");

trunk/arch/arm/kernel/perf_event_v6.c

@@ -467,6 +467,23 @@ armv6pmu_enable_event(struct hw_perf_event *hwc,
 	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 
+static int counter_is_active(unsigned long pmcr, int idx)
+{
+	unsigned long mask = 0;
+	if (idx == ARMV6_CYCLE_COUNTER)
+		mask = ARMV6_PMCR_CCOUNT_IEN;
+	else if (idx == ARMV6_COUNTER0)
+		mask = ARMV6_PMCR_COUNT0_IEN;
+	else if (idx == ARMV6_COUNTER1)
+		mask = ARMV6_PMCR_COUNT1_IEN;
+
+	if (mask)
+		return pmcr & mask;
+
+	WARN_ONCE(1, "invalid counter number (%d)\n", idx);
+	return 0;
+}
+
 static irqreturn_t
 armv6pmu_handle_irq(int irq_num,
 		    void *dev)
@@ -496,8 +513,7 @@ armv6pmu_handle_irq(int irq_num,
 		struct perf_event *event = cpuc->events[idx];
 		struct hw_perf_event *hwc;
 
-		/* Ignore if we don't have an event. */
-		if (!event)
+		if (!counter_is_active(pmcr, idx))
 			continue;
 
 		/*
@@ -508,7 +524,7 @@ armv6pmu_handle_irq(int irq_num,
 			continue;
 
 		hwc = &event->hw;
-		armpmu_event_update(event, hwc, idx);
+		armpmu_event_update(event, hwc, idx, 1);
 		data.period = event->hw.last_period;
 		if (!armpmu_event_set_period(event, hwc, idx))
 			continue;

trunk/arch/arm/kernel/perf_event_v7.c

@@ -809,11 +809,6 @@ static inline int armv7_pmnc_disable_intens(int idx)
 
 	counter = ARMV7_IDX_TO_COUNTER(idx);
 	asm volatile("mcr p15, 0, %0, c9, c14, 2" : : "r" (BIT(counter)));
-	isb();
-	/* Clear the overflow flag in case an interrupt is pending. */
-	asm volatile("mcr p15, 0, %0, c9, c12, 3" : : "r" (BIT(counter)));
-	isb();
-
 	return idx;
 }
 
@@ -960,10 +955,6 @@ static irqreturn_t armv7pmu_handle_irq(int irq_num, void *dev)
 		struct perf_event *event = cpuc->events[idx];
 		struct hw_perf_event *hwc;
 
-		/* Ignore if we don't have an event. */
-		if (!event)
-			continue;
-
 		/*
 		 * We have a single interrupt for all counters. Check that
 		 * each counter has overflowed before we process it.
@@ -972,7 +963,7 @@ static irqreturn_t armv7pmu_handle_irq(int irq_num, void *dev)
 			continue;
 
 		hwc = &event->hw;
-		armpmu_event_update(event, hwc, idx);
+		armpmu_event_update(event, hwc, idx, 1);
 		data.period = event->hw.last_period;
 		if (!armpmu_event_set_period(event, hwc, idx))
 			continue;

trunk/arch/arm/kernel/perf_event_xscale.c

@@ -255,14 +255,11 @@ xscale1pmu_handle_irq(int irq_num, void *dev)
 		struct perf_event *event = cpuc->events[idx];
 		struct hw_perf_event *hwc;
 
-		if (!event)
-			continue;
-
 		if (!xscale1_pmnc_counter_has_overflowed(pmnc, idx))
 			continue;
 
 		hwc = &event->hw;
-		armpmu_event_update(event, hwc, idx);
+		armpmu_event_update(event, hwc, idx, 1);
 		data.period = event->hw.last_period;
 		if (!armpmu_event_set_period(event, hwc, idx))
 			continue;
@@ -595,14 +592,11 @@ xscale2pmu_handle_irq(int irq_num, void *dev)
 		struct perf_event *event = cpuc->events[idx];
 		struct hw_perf_event *hwc;
 
-		if (!event)
-			continue;
-
-		if (!xscale2_pmnc_counter_has_overflowed(of_flags, idx))
+		if (!xscale2_pmnc_counter_has_overflowed(pmnc, idx))
 			continue;
 
 		hwc = &event->hw;
-		armpmu_event_update(event, hwc, idx);
+		armpmu_event_update(event, hwc, idx, 1);
 		data.period = event->hw.last_period;
 		if (!armpmu_event_set_period(event, hwc, idx))
 			continue;
@@ -669,7 +663,7 @@ xscale2pmu_enable_event(struct hw_perf_event *hwc, int idx)
 static void
 xscale2pmu_disable_event(struct hw_perf_event *hwc, int idx)
 {
-	unsigned long flags, ien, evtsel, of_flags;
+	unsigned long flags, ien, evtsel;
 	struct pmu_hw_events *events = cpu_pmu->get_hw_events();
 
 	ien = xscale2pmu_read_int_enable();
@@ -678,31 +672,26 @@ xscale2pmu_disable_event(struct hw_perf_event *hwc, int idx)
 	switch (idx) {
 	case XSCALE_CYCLE_COUNTER:
 		ien &= ~XSCALE2_CCOUNT_INT_EN;
-		of_flags = XSCALE2_CCOUNT_OVERFLOW;
 		break;
 	case XSCALE_COUNTER0:
 		ien &= ~XSCALE2_COUNT0_INT_EN;
 		evtsel &= ~XSCALE2_COUNT0_EVT_MASK;
 		evtsel |= XSCALE_PERFCTR_UNUSED << XSCALE2_COUNT0_EVT_SHFT;
-		of_flags = XSCALE2_COUNT0_OVERFLOW;
 		break;
 	case XSCALE_COUNTER1:
 		ien &= ~XSCALE2_COUNT1_INT_EN;
 		evtsel &= ~XSCALE2_COUNT1_EVT_MASK;
 		evtsel |= XSCALE_PERFCTR_UNUSED << XSCALE2_COUNT1_EVT_SHFT;
-		of_flags = XSCALE2_COUNT1_OVERFLOW;
 		break;
 	case XSCALE_COUNTER2:
 		ien &= ~XSCALE2_COUNT2_INT_EN;
 		evtsel &= ~XSCALE2_COUNT2_EVT_MASK;
 		evtsel |= XSCALE_PERFCTR_UNUSED << XSCALE2_COUNT2_EVT_SHFT;
-		of_flags = XSCALE2_COUNT2_OVERFLOW;
 		break;
 	case XSCALE_COUNTER3:
 		ien &= ~XSCALE2_COUNT3_INT_EN;
 		evtsel &= ~XSCALE2_COUNT3_EVT_MASK;
 		evtsel |= XSCALE_PERFCTR_UNUSED << XSCALE2_COUNT3_EVT_SHFT;
-		of_flags = XSCALE2_COUNT3_OVERFLOW;
 		break;
 	default:
 		WARN_ONCE(1, "invalid counter number (%d)\n", idx);
@@ -712,7 +701,6 @@ xscale2pmu_disable_event(struct hw_perf_event *hwc, int idx)
 	raw_spin_lock_irqsave(&events->pmu_lock, flags);
 	xscale2pmu_write_event_select(evtsel);
 	xscale2pmu_write_int_enable(ien);
-	xscale2pmu_write_overflow_flags(of_flags);
 	raw_spin_unlock_irqrestore(&events->pmu_lock, flags);
 }
 

trunk/arch/arm/mach-omap2/id.c

@@ -343,7 +343,6 @@ static void __init omap3_check_revision(const char **cpu_rev)
 	case 0xb944:
 		omap_revision = AM335X_REV_ES1_0;
 		*cpu_rev = "1.0";
-		break;
 	case 0xb8f2:
 		switch (rev) {
 		case 0: