stmmac: add mixed burst for DMA

In mixed burst (MB) mode, the AHB master always initiates
the bursts with fixed-size when the DMA requests transfers
of size less than or equal to 16 beats.
This patch adds the MB support and the flag that can be
passed from the platform to select it.
MB mode can also give some benefits in terms of performances
on some platforms.

v2: fixed Coding Style

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/stmicro/stmmac/common.h

@@ -247,8 +247,8 @@ struct stmmac_desc_ops {
 
 struct stmmac_dma_ops {
 	/* DMA core initialization */
-	int (*init) (void __iomem *ioaddr, int pbl, int fb, int burst_len,
-			u32 dma_tx, u32 dma_rx);
+	int (*init) (void __iomem *ioaddr, int pbl, int fb, int mb,
+		     int burst_len, u32 dma_tx, u32 dma_rx);
 	/* Dump DMA registers */
 	void (*dump_regs) (void __iomem *ioaddr);
 	/* Set tx/rx threshold in the csr6 register

drivers/net/ethernet/stmicro/stmmac/dwmac1000.h

@@ -141,6 +141,7 @@ enum rx_tx_priority_ratio {
 };
 
 #define DMA_BUS_MODE_FB		0x00010000	/* Fixed burst */
+#define DMA_BUS_MODE_MB		0x04000000	/* Mixed burst */
 #define DMA_BUS_MODE_RPBL_MASK	0x003e0000	/* Rx-Programmable Burst Len */
 #define DMA_BUS_MODE_RPBL_SHIFT	17
 #define DMA_BUS_MODE_USP	0x00800000

drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c

@@ -31,7 +31,7 @@
 #include "dwmac_dma.h"
 
 static int dwmac1000_dma_init(void __iomem *ioaddr, int pbl, int fb,
-			      int burst_len, u32 dma_tx, u32 dma_rx)
+			      int mb, int burst_len, u32 dma_tx, u32 dma_rx)
 {
 	u32 value = readl(ioaddr + DMA_BUS_MODE);
 	int limit;
@@ -66,6 +66,10 @@ static int dwmac1000_dma_init(void __iomem *ioaddr, int pbl, int fb,
 	if (fb)
 		value |= DMA_BUS_MODE_FB;
 
+	/* Mixed Burst has no effect when fb is set */
+	if (mb)
+		value |= DMA_BUS_MODE_MB;
+
 #ifdef CONFIG_STMMAC_DA
 	value |= DMA_BUS_MODE_DA;	/* Rx has priority over tx */
 #endif

drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c

@@ -33,7 +33,7 @@
 #include "dwmac_dma.h"
 
 static int dwmac100_dma_init(void __iomem *ioaddr, int pbl, int fb,
-			     int burst_len, u32 dma_tx, u32 dma_rx)
+			     int mb, int burst_len, u32 dma_tx, u32 dma_rx)
 {
 	u32 value = readl(ioaddr + DMA_BUS_MODE);
 	int limit;

drivers/net/ethernet/stmicro/stmmac/stmmac_main.c

@@ -925,17 +925,19 @@ static void stmmac_check_ether_addr(struct stmmac_priv *priv)
 static int stmmac_init_dma_engine(struct stmmac_priv *priv)
 {
 	int pbl = DEFAULT_DMA_PBL, fixed_burst = 0, burst_len = 0;
+	int mixed_burst = 0;
 
 	/* Some DMA parameters can be passed from the platform;
 	 * in case of these are not passed we keep a default
 	 * (good for all the chips) and init the DMA! */
 	if (priv->plat->dma_cfg) {
 		pbl = priv->plat->dma_cfg->pbl;
 		fixed_burst = priv->plat->dma_cfg->fixed_burst;
+		mixed_burst = priv->plat->dma_cfg->mixed_burst;
 		burst_len = priv->plat->dma_cfg->burst_len;
 	}
 
-	return priv->hw->dma->init(priv->ioaddr, pbl, fixed_burst,
+	return priv->hw->dma->init(priv->ioaddr, pbl, fixed_burst, mixed_burst,
 				   burst_len, priv->dma_tx_phy,
 				   priv->dma_rx_phy);
 }

include/linux/stmmac.h

@@ -86,6 +86,7 @@ struct stmmac_mdio_bus_data {
 struct stmmac_dma_cfg {
 	int pbl;
 	int fixed_burst;
+	int mixed_burst;
 	int burst_len;
 };