---

yaml
---
r: 122910
b: refs/heads/master
c: e855aac
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 0e49e64526ccd8cb78d7c4b4a732024ff221d4d0
+refs/heads/master: e855aac805dd9c68b6fabe395cbc8e05f0eda6e4

trunk/drivers/net/ixgbe/ixgbe_82598.c

@@ -177,9 +177,9 @@ static s32 ixgbe_get_link_capabilities_82598(struct ixgbe_hw *hw,
  *
  *  Determines the link capabilities by reading the AUTOC register.
  **/
-s32 ixgbe_get_copper_link_capabilities_82598(struct ixgbe_hw *hw,
-                                             ixgbe_link_speed *speed,
-                                             bool *autoneg)
+static s32 ixgbe_get_copper_link_capabilities_82598(struct ixgbe_hw *hw,
+						    ixgbe_link_speed *speed,
+						    bool *autoneg)
 {
 	s32 status = IXGBE_ERR_LINK_SETUP;
 	u16 speed_ability;
@@ -242,7 +242,7 @@ static enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw)
  *  Configures the flow control settings based on SW configuration.  This
  *  function is used for 802.3x flow control configuration only.
  **/
-s32 ixgbe_setup_fc_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
+static s32 ixgbe_setup_fc_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
 {
 	u32 frctl_reg;
 	u32 rmcs_reg;
@@ -726,7 +726,7 @@ static s32 ixgbe_reset_hw_82598(struct ixgbe_hw *hw)
  *  @rar: receive address register index to associate with a VMDq index
  *  @vmdq: VMDq set index
  **/
-s32 ixgbe_set_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
+static s32 ixgbe_set_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
 {
 	u32 rar_high;
 
@@ -770,8 +770,8 @@ static s32 ixgbe_clear_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq)
  *
  *  Turn on/off specified VLAN in the VLAN filter table.
  **/
-s32 ixgbe_set_vfta_82598(struct ixgbe_hw *hw, u32 vlan, u32 vind,
-                         bool vlan_on)
+static s32 ixgbe_set_vfta_82598(struct ixgbe_hw *hw, u32 vlan, u32 vind,
+				bool vlan_on)
 {
 	u32 regindex;
 	u32 bitindex;
@@ -894,7 +894,7 @@ static s32 ixgbe_blink_led_stop_82598(struct ixgbe_hw *hw, u32 index)
  *
  *  Performs read operation to Atlas analog register specified.
  **/
-s32 ixgbe_read_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 *val)
+static s32 ixgbe_read_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 *val)
 {
 	u32  atlas_ctl;
 
@@ -916,7 +916,7 @@ s32 ixgbe_read_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 *val)
  *
  *  Performs write operation to Atlas analog register specified.
  **/
-s32 ixgbe_write_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 val)
+static s32 ixgbe_write_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 val)
 {
 	u32  atlas_ctl;
 
@@ -937,8 +937,8 @@ s32 ixgbe_write_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 val)
  *
  *  Performs byte read operation to SFP module's EEPROM over I2C interface.
  **/
-s32 ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw *hw, u8 byte_offset,
-                                u8 *eeprom_data)
+static s32 ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw *hw, u8 byte_offset,
+				       u8 *eeprom_data)
 {
 	s32 status = 0;
 	u16 sfp_addr = 0;
@@ -997,7 +997,7 @@ s32 ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw *hw, u8 byte_offset,
  *
  *  Determines physical layer capabilities of the current configuration.
  **/
-s32 ixgbe_get_supported_physical_layer_82598(struct ixgbe_hw *hw)
+static s32 ixgbe_get_supported_physical_layer_82598(struct ixgbe_hw *hw)
 {
 	s32 physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN;
 

trunk/drivers/net/ixgbe/ixgbe_dcb_82598.c

@@ -97,8 +97,8 @@ s32 ixgbe_dcb_get_pfc_stats_82598(struct ixgbe_hw *hw,
  *
  * Configure packet buffers for DCB mode.
  */
-s32 ixgbe_dcb_config_packet_buffers_82598(struct ixgbe_hw *hw,
-                                          struct ixgbe_dcb_config *dcb_config)
+static s32 ixgbe_dcb_config_packet_buffers_82598(struct ixgbe_hw *hw,
+						 struct ixgbe_dcb_config *dcb_config)
 {
 	s32 ret_val = 0;
 	u32 value = IXGBE_RXPBSIZE_64KB;