---

yaml
---
r: 217099
b: refs/heads/master
c: e5f5c99
h: refs/heads/master
i:
  217097: 0406cf6
  217095: 8ef835d
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 2ee321440e3a594dcdd9981e68e5e302447047a2
+refs/heads/master: e5f5c99a39375ce533aacfdfb269978070121e1c

trunk/Documentation/hwmon/ltc4261

@@ -0,0 +1,63 @@
+Kernel driver ltc4261
+=====================
+
+Supported chips:
+  * Linear Technology LTC4261
+    Prefix: 'ltc4261'
+    Addresses scanned: -
+    Datasheet:
+        http://cds.linear.com/docs/Datasheet/42612fb.pdf
+
+Author: Guenter Roeck <guenter.roeck@ericsson.com>
+
+
+Description
+-----------
+
+The LTC4261/LTC4261-2 negative voltage Hot Swap controllers allow a board
+to be safely inserted and removed from a live backplane.
+
+
+Usage Notes
+-----------
+
+This driver does not probe for LTC4261 devices, since there is no register
+which can be safely used to identify the chip. You will have to instantiate
+the devices explicitly.
+
+Example: the following will load the driver for an LTC4261 at address 0x10
+on I2C bus #1:
+$ modprobe ltc4261
+$ echo ltc4261 0x10 > /sys/bus/i2c/devices/i2c-1/new_device
+
+
+Sysfs entries
+-------------
+
+Voltage readings provided by this driver are reported as obtained from the ADC
+registers. If a set of voltage divider resistors is installed, calculate the
+real voltage by multiplying the reported value with (R1+R2)/R2, where R1 is the
+value of the divider resistor against the measured voltage and R2 is the value
+of the divider resistor against Ground.
+
+Current reading provided by this driver is reported as obtained from the ADC
+Current Sense register. The reported value assumes that a 1 mOhm sense resistor
+is installed. If a different sense resistor is installed, calculate the real
+current by dividing the reported value by the sense resistor value in mOhm.
+
+The chip has two voltage sensors, but only one set of voltage alarm status bits.
+In many many designs, those alarms are associated with the ADIN2 sensor, due to
+the proximity of the ADIN2 pin to the OV pin. ADIN2 is, however, not available
+on all chip variants. To ensure that the alarm condition is reported to the user,
+report it with both voltage sensors.
+
+in1_input		ADIN2 voltage (mV)
+in1_min_alarm		ADIN/ADIN2 Undervoltage alarm
+in1_max_alarm		ADIN/ADIN2 Overvoltage alarm
+
+in2_input		ADIN voltage (mV)
+in2_min_alarm		ADIN/ADIN2 Undervoltage alarm
+in2_max_alarm		ADIN/ADIN2 Overvoltage alarm
+
+curr1_input		SENSE current (mA)
+curr1_alarm		SENSE overcurrent alarm

trunk/MAINTAINERS

@@ -3765,6 +3765,13 @@ L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	drivers/scsi/sym53c8xx_2/
 
+LTC4261 HARDWARE MONITOR DRIVER
+M:	Guenter Roeck <linux@roeck-us.net>
+L:	lm-sensors@lm-sensors.org
+S:	Maintained
+F:	Documentation/hwmon/ltc4261
+F:	drivers/hwmon/ltc4261.c
+
 LTP (Linux Test Project)
 M:	Rishikesh K Rajak <risrajak@linux.vnet.ibm.com>
 M:	Garrett Cooper <yanegomi@gmail.com>

trunk/drivers/hwmon/Kconfig

@@ -654,6 +654,17 @@ config SENSORS_LTC4245
 	  This driver can also be built as a module. If so, the module will
 	  be called ltc4245.
 
+config SENSORS_LTC4261
+	tristate "Linear Technology LTC4261"
+	depends on I2C && EXPERIMENTAL
+	default n
+	help
+	  If you say yes here you get support for Linear Technology LTC4261
+	  Negative Voltage Hot Swap Controller I2C interface.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called ltc4261.
+
 config SENSORS_LM95241
 	tristate "National Semiconductor LM95241 sensor chip"
 	depends on I2C

trunk/drivers/hwmon/Makefile

@@ -79,6 +79,7 @@ obj-$(CONFIG_SENSORS_LM93)	+= lm93.o
 obj-$(CONFIG_SENSORS_LM95241)	+= lm95241.o
 obj-$(CONFIG_SENSORS_LTC4215)	+= ltc4215.o
 obj-$(CONFIG_SENSORS_LTC4245)	+= ltc4245.o
+obj-$(CONFIG_SENSORS_LTC4261)	+= ltc4261.o
 obj-$(CONFIG_SENSORS_MAX1111)	+= max1111.o
 obj-$(CONFIG_SENSORS_MAX1619)	+= max1619.o
 obj-$(CONFIG_SENSORS_MAX6650)	+= max6650.o