Merge branches 'pci/host', 'pci/host-designware', 'pci/host-hisi', 'p…

…ci/host-qcom' and 'pci/host-rcar' into next

* pci/host:
  PCI: host: Add of_pci_get_host_bridge_resources() stub
  PCI: host: Mark PCIe/PCI (MSI) IRQ cascade handlers as IRQF_NO_THREAD

* pci/host-designware:
  PCI: designware: Make config accessor override checking symmetric
  PCI: designware: Simplify control flow

* pci/host-hisi:
  PCI: hisi: Add support for HiSilicon Hip06 PCIe host controllers

* pci/host-qcom:
  ARM: dts: ifc6410: enable PCIe DT node for this board
  ARM: dts: apq8064: add PCIe devicetree node
  PCI: qcom: Add Qualcomm PCIe controller driver
  PCI: qcom: Document PCIe devicetree bindings
  PCI: designware: Ensure ATU is enabled before IO/conf space accesses

* pci/host-rcar:
  PCI: rcar: Add Gen2 PHY setup to pcie-rcar
  PCI: rcar: Add runtime PM support to pcie-rcar
  PCI: rcar: Remove unused pci_sys_data struct from pcie-rcar

Documentation/devicetree/bindings/pci/hisilicon-pcie.txt

@@ -1,4 +1,4 @@
-HiSilicon PCIe host bridge DT description
+HiSilicon Hip05 and Hip06 PCIe host bridge DT description
 
 HiSilicon PCIe host controller is based on Designware PCI core.
 It shares common functions with PCIe Designware core driver and inherits
@@ -7,8 +7,8 @@ Documentation/devicetree/bindings/pci/designware-pci.txt.
 
 Additional properties are described here:
 
-Required properties:
-- compatible: Should contain "hisilicon,hip05-pcie".
+Required properties
+- compatible: Should contain "hisilicon,hip05-pcie" or "hisilicon,hip06-pcie".
 - reg: Should contain rc_dbi, config registers location and length.
 - reg-names: Must include the following entries:
   "rc_dbi": controller configuration registers;
@@ -20,7 +20,7 @@ Optional properties:
 - status: Either "ok" or "disabled".
 - dma-coherent: Present if DMA operations are coherent.
 
-Example:
+Hip05 Example (note that Hip06 is the same except compatible):
 	pcie@0xb0080000 {
 		compatible = "hisilicon,hip05-pcie", "snps,dw-pcie";
 		reg = <0 0xb0080000 0 0x10000>, <0x220 0x00000000 0 0x2000>;

Documentation/devicetree/bindings/pci/qcom,pcie.txt

@@ -0,0 +1,233 @@
+* Qualcomm PCI express root complex
+
+- compatible:
+	Usage: required
+	Value type: <stringlist>
+	Definition: Value should contain
+			- "qcom,pcie-ipq8064" for ipq8064
+			- "qcom,pcie-apq8064" for apq8064
+			- "qcom,pcie-apq8084" for apq8084
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: Register ranges as listed in the reg-names property
+
+- reg-names:
+	Usage: required
+	Value type: <stringlist>
+	Definition: Must include the following entries
+			- "parf"   Qualcomm specific registers
+			- "dbi"	   Designware PCIe registers
+			- "elbi"   External local bus interface registers
+			- "config" PCIe configuration space
+
+- device_type:
+	Usage: required
+	Value type: <string>
+	Definition: Should be "pci". As specified in designware-pcie.txt
+
+- #address-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: Should be 3. As specified in designware-pcie.txt
+
+- #size-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: Should be 2. As specified in designware-pcie.txt
+
+- ranges:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: As specified in designware-pcie.txt
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: MSI interrupt
+
+- interrupt-names:
+	Usage: required
+	Value type: <stringlist>
+	Definition: Should contain "msi"
+
+- #interrupt-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: Should be 1. As specified in designware-pcie.txt
+
+- interrupt-map-mask:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: As specified in designware-pcie.txt
+
+- interrupt-map:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: As specified in designware-pcie.txt
+
+- clocks:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: List of phandle and clock specifier pairs as listed
+		    in clock-names property
+
+- clock-names:
+	Usage: required
+	Value type: <stringlist>
+	Definition: Should contain the following entries
+			- "iface"	Configuration AHB clock
+
+- clock-names:
+	Usage: required for ipq/apq8064
+	Value type: <stringlist>
+	Definition: Should contain the following entries
+			- "core"	Clocks the pcie hw block
+			- "phy"		Clocks the pcie PHY block
+- clock-names:
+	Usage: required for apq8084
+	Value type: <stringlist>
+	Definition: Should contain the following entries
+			- "aux"		Auxiliary (AUX) clock
+			- "bus_master"	Master AXI clock
+			- "bus_slave"	Slave AXI clock
+- resets:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: List of phandle and reset specifier pairs as listed
+		    in reset-names property
+
+- reset-names:
+	Usage: required for ipq/apq8064
+	Value type: <stringlist>
+	Definition: Should contain the following entries
+			- "axi"  AXI reset
+			- "ahb"  AHB reset
+			- "por"  POR reset
+			- "pci"  PCI reset
+			- "phy"  PHY reset
+
+- reset-names:
+	Usage: required for apq8084
+	Value type: <stringlist>
+	Definition: Should contain the following entries
+			- "core" Core reset
+
+- power-domains:
+	Usage: required for apq8084
+	Value type: <prop-encoded-array>
+	Definition: A phandle and power domain specifier pair to the
+		    power domain which is responsible for collapsing
+		    and restoring power to the peripheral
+
+- vdda-supply:
+	Usage: required
+	Value type: <phandle>
+	Definition: A phandle to the core analog power supply
+
+- vdda_phy-supply:
+	Usage: required for ipq/apq8064
+	Value type: <phandle>
+	Definition: A phandle to the analog power supply for PHY
+
+- vdda_refclk-supply:
+	Usage: required for ipq/apq8064
+	Value type: <phandle>
+	Definition: A phandle to the analog power supply for IC which generates
+		    reference clock
+
+- phys:
+	Usage: required for apq8084
+	Value type: <phandle>
+	Definition: List of phandle(s) as listed in phy-names property
+
+- phy-names:
+	Usage: required for apq8084
+	Value type: <stringlist>
+	Definition: Should contain "pciephy"
+
+- <name>-gpios:
+	Usage: optional
+	Value type: <prop-encoded-array>
+	Definition: List of phandle and gpio specifier pairs. Should contain
+			- "perst-gpios"	PCIe endpoint reset signal line
+			- "wake-gpios"	PCIe endpoint wake signal line
+
+* Example for ipq/apq8064
+	pcie@1b500000 {
+		compatible = "qcom,pcie-apq8064", "qcom,pcie-ipq8064", "snps,dw-pcie";
+		reg = <0x1b500000 0x1000
+		       0x1b502000 0x80
+		       0x1b600000 0x100
+		       0x0ff00000 0x100000>;
+		reg-names = "dbi", "elbi", "parf", "config";
+		device_type = "pci";
+		linux,pci-domain = <0>;
+		bus-range = <0x00 0xff>;
+		num-lanes = <1>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges = <0x81000000 0 0 0x0fe00000 0 0x00100000   /* I/O */
+			  0x82000000 0 0 0x08000000 0 0x07e00000>; /* memory */
+		interrupts = <GIC_SPI 238 IRQ_TYPE_NONE>;
+		interrupt-names = "msi";
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0x7>;
+		interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+				<0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+				<0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+				<0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+		clocks = <&gcc PCIE_A_CLK>,
+			 <&gcc PCIE_H_CLK>,
+			 <&gcc PCIE_PHY_CLK>;
+		clock-names = "core", "iface", "phy";
+		resets = <&gcc PCIE_ACLK_RESET>,
+			 <&gcc PCIE_HCLK_RESET>,
+			 <&gcc PCIE_POR_RESET>,
+			 <&gcc PCIE_PCI_RESET>,
+			 <&gcc PCIE_PHY_RESET>;
+		reset-names = "axi", "ahb", "por", "pci", "phy";
+		pinctrl-0 = <&pcie_pins_default>;
+		pinctrl-names = "default";
+	};
+
+* Example for apq8084
+	pcie0@fc520000 {
+		compatible = "qcom,pcie-apq8084", "snps,dw-pcie";
+		reg = <0xfc520000 0x2000>,
+		      <0xff000000 0x1000>,
+		      <0xff001000 0x1000>,
+		      <0xff002000 0x2000>;
+		reg-names = "parf", "dbi", "elbi", "config";
+		device_type = "pci";
+		linux,pci-domain = <0>;
+		bus-range = <0x00 0xff>;
+		num-lanes = <1>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges = <0x81000000 0 0          0xff200000 0 0x00100000   /* I/O */
+			  0x82000000 0 0x00300000 0xff300000 0 0x00d00000>; /* memory */
+		interrupts = <GIC_SPI 243 IRQ_TYPE_NONE>;
+		interrupt-names = "msi";
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0x7>;
+		interrupt-map = <0 0 0 1 &intc 0 244 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+				<0 0 0 2 &intc 0 245 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+				<0 0 0 3 &intc 0 247 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+				<0 0 0 4 &intc 0 248 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+		clocks = <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+			 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+			 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
+			 <&gcc GCC_PCIE_0_AUX_CLK>;
+		clock-names = "iface", "master_bus", "slave_bus", "aux";
+		resets = <&gcc GCC_PCIE_0_BCR>;
+		reset-names = "core";
+		power-domains = <&gcc PCIE0_GDSC>;
+		vdda-supply = <&pma8084_l3>;
+		phys = <&pciephy0>;
+		phy-names = "pciephy";
+		perst-gpio = <&tlmm 70 GPIO_ACTIVE_LOW>;
+		pinctrl-0 = <&pcie0_pins_default>;
+		pinctrl-names = "default";
+	};

MAINTAINERS

@@ -8240,11 +8240,19 @@ F:	drivers/pci/host/pci-xgene-msi.c
 
 PCIE DRIVER FOR HISILICON
 M:	Zhou Wang <wangzhou1@hisilicon.com>
+M:	Gabriele Paoloni <gabriele.paoloni@huawei.com>
 L:	linux-pci@vger.kernel.org
 S:	Maintained
 F:	Documentation/devicetree/bindings/pci/hisilicon-pcie.txt
 F:	drivers/pci/host/pcie-hisi.c
 
+PCIE DRIVER FOR QUALCOMM MSM
+M:     Stanimir Varbanov <svarbanov@mm-sol.com>
+L:     linux-pci@vger.kernel.org
+L:     linux-arm-msm@vger.kernel.org
+S:     Maintained
+F:     drivers/pci/host/*qcom*
+
 PCMCIA SUBSYSTEM
 P:	Linux PCMCIA Team
 L:	linux-pcmcia@lists.infradead.org

arch/arm/boot/dts/qcom-apq8064-ifc6410.dts

@@ -47,6 +47,18 @@
 					bias-disable;
 				};
 			};
+
+			pcie_pins: pcie_pinmux {
+				mux {
+					pins = "gpio27";
+					function = "gpio";
+				};
+				conf {
+					pins = "gpio27";
+					drive-strength = <12>;
+					bias-disable;
+				};
+			};
 		};
 
 		rpm@108000 {
@@ -123,6 +135,10 @@
 				pm8921_lvs1: lvs1 {
 					bias-pull-down;
 				};
+
+				lvs6 {
+					bias-pull-down;
+				};
 			};
 		};
 
@@ -231,6 +247,16 @@
 			status = "okay";
 		};
 
+		pci@1b500000 {
+			status = "ok";
+			vdda-supply = <&pm8921_s3>;
+			vdda_phy-supply = <&pm8921_lvs6>;
+			vdda_refclk-supply = <&ext_3p3v>;
+			pinctrl-0 = <&pcie_pins>;
+			pinctrl-names = "default";
+			perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+		};
+
 		qcom,ssbi@500000 {
 			pmic@0 {
 				gpio@150 {

arch/arm/boot/dts/qcom-apq8064.dtsi

@@ -659,5 +659,41 @@
 			compatible = "qcom,tcsr-apq8064", "syscon";
 			reg = <0x1a400000 0x100>;
 		};
+
+		pcie: pci@1b500000 {
+			compatible = "qcom,pcie-apq8064", "snps,dw-pcie";
+			reg = <0x1b500000 0x1000
+			       0x1b502000 0x80
+			       0x1b600000 0x100
+			       0x0ff00000 0x100000>;
+			reg-names = "dbi", "elbi", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <0>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges = <0x81000000 0 0 0x0fe00000 0 0x00100000   /* I/O */
+				  0x82000000 0 0 0x08000000 0 0x07e00000>; /* memory */
+			interrupts = <GIC_SPI 238 IRQ_TYPE_NONE>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+			clocks = <&gcc PCIE_A_CLK>,
+				 <&gcc PCIE_H_CLK>,
+				 <&gcc PCIE_PHY_REF_CLK>;
+			clock-names = "core", "iface", "phy";
+			resets = <&gcc PCIE_ACLK_RESET>,
+				 <&gcc PCIE_HCLK_RESET>,
+				 <&gcc PCIE_POR_RESET>,
+				 <&gcc PCIE_PCI_RESET>,
+				 <&gcc PCIE_PHY_RESET>;
+			reset-names = "axi", "ahb", "por", "pci", "phy";
+			status = "disabled";
+		};
 	};
 };

drivers/pci/host/Kconfig

@@ -173,10 +173,21 @@ config PCIE_ALTERA_MSI
 
 config PCI_HISI
 	depends on OF && ARM64
-	bool "HiSilicon SoC HIP05 PCIe controller"
+	bool "HiSilicon Hip05 and Hip06 SoCs PCIe controllers"
 	select PCIEPORTBUS
 	select PCIE_DW
 	help
-	  Say Y here if you want PCIe controller support on HiSilicon HIP05 SoC
+	  Say Y here if you want PCIe controller support on HiSilicon
+	  Hip05 and Hip06 SoCs
+
+config PCIE_QCOM
+	bool "Qualcomm PCIe controller"
+	depends on ARCH_QCOM && OF
+	select PCIE_DW
+	select PCIEPORTBUS
+	help
+	  Say Y here to enable PCIe controller support on Qualcomm SoCs. The
+	  PCIe controller uses the Designware core plus Qualcomm-specific
+	  hardware wrappers.
 
 endmenu

drivers/pci/host/Makefile

@@ -21,3 +21,4 @@ obj-$(CONFIG_PCIE_IPROC_BCMA) += pcie-iproc-bcma.o
 obj-$(CONFIG_PCIE_ALTERA) += pcie-altera.o
 obj-$(CONFIG_PCIE_ALTERA_MSI) += pcie-altera-msi.o
 obj-$(CONFIG_PCI_HISI) += pcie-hisi.o
+obj-$(CONFIG_PCIE_QCOM) += pcie-qcom.o