Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Conflicts:
	net/bridge/br_mdb.c

br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.

Signed-off-by: David S. Miller <davem@davemloft.net>

.mailmap

@@ -116,6 +116,7 @@ Shiraz Hashim <shiraz.linux.kernel@gmail.com> <shiraz.hashim@st.com>
 Simon Kelley <simon@thekelleys.org.uk>
 Stéphane Witzmann <stephane.witzmann@ubpmes.univ-bpclermont.fr>
 Stephen Hemminger <shemminger@osdl.org>
+Sudeep Holla <sudeep.holla@arm.com> Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
 Sumit Semwal <sumit.semwal@ti.com>
 Tejun Heo <htejun@gmail.com>
 Thomas Graf <tgraf@suug.ch>
@@ -125,7 +126,9 @@ Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
 Uwe Kleine-König <ukl@pengutronix.de>
 Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
 Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
-Viresh Kumar <viresh.linux@gmail.com> <viresh.kumar@st.com>
+Viresh Kumar <vireshk@kernel.org> <viresh.kumar@st.com>
+Viresh Kumar <vireshk@kernel.org> <viresh.linux@gmail.com>
+Viresh Kumar <vireshk@kernel.org> <viresh.kumar2@arm.com>
 Takashi YOSHII <takashi.yoshii.zj@renesas.com>
 Yusuke Goda <goda.yusuke@renesas.com>
 Gustavo Padovan <gustavo@las.ic.unicamp.br>

Documentation/ABI/testing/sysfs-bus-iio

@@ -1234,10 +1234,8 @@ Description:
 		object is near the sensor, usually be observing
 		reflectivity of infrared or ultrasound emitted.
 		Often these sensors are unit less and as such conversion
-		to SI units is not possible.  Where it is, the units should
-		be meters.  If such a conversion is not possible, the reported
-		values should behave in the same way as a distance, i.e. lower
-		values indicate something is closer to the sensor.
+		to SI units is not possible. Higher proximity measurements
+		indicate closer objects, and vice versa.
 
 What:		/sys/.../iio:deviceX/in_illuminance_input
 What:		/sys/.../iio:deviceX/in_illuminance_raw

Documentation/DocBook/drm.tmpl

@@ -3383,7 +3383,7 @@ void intel_crt_init(struct drm_device *dev)
 	<td valign="top" >TBD</td>
 	</tr>
 	<tr>
-	<td rowspan="2" valign="top" >omap</td>
+	<td valign="top" >omap</td>
 	<td valign="top" >Generic</td>
 	<td valign="top" >“zorder”</td>
 	<td valign="top" >RANGE</td>

Documentation/arm/SPEAr/overview.txt

@@ -60,4 +60,4 @@ Introduction
   Document Author
   ---------------
 
-  Viresh Kumar <viresh.linux@gmail.com>, (c) 2010-2012 ST Microelectronics
+  Viresh Kumar <vireshk@kernel.org>, (c) 2010-2012 ST Microelectronics

Documentation/device-mapper/cache.txt

@@ -258,6 +258,12 @@ cache metadata mode      : ro if read-only, rw if read-write
 	no further I/O will be permitted and the status will just
 	contain the string 'Fail'.  The userspace recovery tools
 	should then be used.
+needs_check		 : 'needs_check' if set, '-' if not set
+	A metadata operation has failed, resulting in the needs_check
+	flag being set in the metadata's superblock.  The metadata
+	device must be deactivated and checked/repaired before the
+	cache can be made fully operational again.  '-' indicates
+	needs_check is not set.
 
 Messages
 --------

Documentation/device-mapper/thin-provisioning.txt

@@ -296,7 +296,7 @@ ii) Status
 	underlying device.  When this is enabled when loading the table,
 	it can get disabled if the underlying device doesn't support it.
 
-    ro|rw
+    ro|rw|out_of_data_space
 	If the pool encounters certain types of device failures it will
 	drop into a read-only metadata mode in which no changes to
 	the pool metadata (like allocating new blocks) are permitted.
@@ -314,6 +314,13 @@ ii) Status
 	module parameter can be used to change this timeout -- it
 	defaults to 60 seconds but may be disabled using a value of 0.
 
+    needs_check
+	A metadata operation has failed, resulting in the needs_check
+	flag being set in the metadata's superblock.  The metadata
+	device must be deactivated and checked/repaired before the
+	thin-pool can be made fully operational again.  '-' indicates
+	needs_check is not set.
+
 iii) Messages
 
     create_thin <dev id>

Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt

@@ -65,8 +65,10 @@ Optional properties:
 - edid: verbatim EDID data block describing attached display.
 - ddc: phandle describing the i2c bus handling the display data
   channel
-- port: A port node with endpoint definitions as defined in
+- port@[0-1]: Port nodes with endpoint definitions as defined in
   Documentation/devicetree/bindings/media/video-interfaces.txt.
+  Port 0 is the input port connected to the IPU display interface,
+  port 1 is the output port connected to a panel.
 
 example:
 
@@ -75,9 +77,29 @@ display@di0 {
 	edid = [edid-data];
 	interface-pix-fmt = "rgb24";
 
-	port {
+	port@0 {
+		reg = <0>;
+
 		display_in: endpoint {
 			remote-endpoint = <&ipu_di0_disp0>;
 		};
 	};
+
+	port@1 {
+		reg = <1>;
+
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+panel {
+	...
+
+	port {
+		panel_in: endpoint {
+			remote-endpoint = <&display_out>;
+		};
+	};
 };

Documentation/kbuild/makefiles.txt

@@ -952,6 +952,14 @@ When kbuild executes, the following steps are followed (roughly):
 	$(KBUILD_ARFLAGS) set by the top level Makefile to "D" (deterministic
 	mode) if this option is supported by $(AR).
 
+    ARCH_CPPFLAGS, ARCH_AFLAGS, ARCH_CFLAGS   Overrides the kbuild defaults
+
+	These variables are appended to the KBUILD_CPPFLAGS,
+	KBUILD_AFLAGS, and KBUILD_CFLAGS, respectively, after the
+	top-level Makefile has set any other flags. This provides a
+	means for an architecture to override the defaults.
+
+
 --- 6.2 Add prerequisites to archheaders:
 
 	The archheaders: rule is used to generate header files that