Merge branch 'kirkwood_dt_for_3.4_v3' of git://git.infradead.org/user…

…s/jcooper/linux-kirkwood into kirkwood/dt

* 'kirkwood_dt_for_3.4_v3' of git://git.infradead.org/users/jcooper/linux-kirkwood:
  ARM: kirkwood: use devicetree for rtc-mv
  ARM: kirkwood: rtc-mv devicetree bindings
  ARM: kirkwood: fdt: define uart[01] as disabled, enable uart0
  ARM: kirkwood: fdt: facilitate new boards during fdt migration
  ARM: kirkwood: fdt: absorb kirkwood_init()
  ARM: kirkwood: fdt: use mrvl ticker symbol
  ARM: orion: wdt: use resource vice direct access
  ARM: Kirkwood: Remove tclk from kirkwood_asoc_platform_data.
  ARM: orion: spi: remove enable_clock_fix which is not used

arch/arm/boot/dts/kirkwood-dreamplug.dts

@@ -4,7 +4,7 @@
 
 / {
 	model = "Globalscale Technologies Dreamplug";
-	compatible = "globalscale,dreamplug-003-ds2001", "globalscale,dreamplug", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+	compatible = "globalscale,dreamplug-003-ds2001", "globalscale,dreamplug", "mrvl,kirkwood-88f6281", "mrvl,kirkwood";
 
 	memory {
 		device_type = "memory";
@@ -15,11 +15,10 @@
 		bootargs = "console=ttyS0,115200n8 earlyprintk";
 	};
 
-	serial@f1012000 {
-		compatible = "ns16550a";
-		reg = <0xf1012000 0xff>;
-		reg-shift = <2>;
-		interrupts = <33>;
-		clock-frequency = <200000000>;
+	ocp@f1000000 {
+		serial@12000 {
+			clock-frequency = <200000000>;
+			status = "ok";
+		};
 	};
 };

arch/arm/boot/dts/kirkwood.dtsi

@@ -1,6 +1,36 @@
 /include/ "skeleton.dtsi"
 
 / {
-	compatible = "marvell,kirkwood";
-};
+	compatible = "mrvl,kirkwood";
+
+	ocp@f1000000 {
+		compatible = "simple-bus";
+		ranges = <0 0xf1000000 0x1000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		serial@12000 {
+			compatible = "ns16550a";
+			reg = <0x12000 0x100>;
+			reg-shift = <2>;
+			interrupts = <33>;
+			/* set clock-frequency in board dts */
+			status = "disabled";
+		};
 
+		serial@12100 {
+			compatible = "ns16550a";
+			reg = <0x12100 0x100>;
+			reg-shift = <2>;
+			interrupts = <34>;
+			/* set clock-frequency in board dts */
+			status = "disabled";
+		};
+
+		rtc@10300 {
+			compatible = "mrvl,kirkwood-rtc", "mrvl,orion-rtc";
+			reg = <0x10300 0x20>;
+			interrupts = <53>;
+		};
+	};
+};

arch/arm/mach-kirkwood/Makefile

@@ -21,3 +21,4 @@ obj-$(CONFIG_MACH_T5325)		+= t5325-setup.o
 
 obj-$(CONFIG_CPU_IDLE)			+= cpuidle.o
 obj-$(CONFIG_ARCH_KIRKWOOD_DT)		+= board-dt.o
+obj-$(CONFIG_MACH_DREAMPLUG_DT)		+= board-dreamplug.o

arch/arm/mach-kirkwood/board-dreamplug.c

@@ -0,0 +1,152 @@
+/*
+ * Copyright 2012 (C), Jason Cooper <jason@lakedaemon.net>
+ *
+ * arch/arm/mach-kirkwood/board-dreamplug.c
+ *
+ * Marvell DreamPlug Reference Board Init for drivers not converted to
+ * flattened device tree yet.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/partitions.h>
+#include <linux/ata_platform.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_fdt.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/flash.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/orion_spi.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <mach/kirkwood.h>
+#include <mach/bridge-regs.h>
+#include <plat/mvsdio.h>
+#include "common.h"
+#include "mpp.h"
+
+struct mtd_partition dreamplug_partitions[] = {
+	{
+		.name	= "u-boot",
+		.size	= SZ_512K,
+		.offset = 0,
+	},
+	{
+		.name	= "u-boot env",
+		.size	= SZ_64K,
+		.offset = SZ_512K + SZ_512K,
+	},
+	{
+		.name	= "dtb",
+		.size	= SZ_64K,
+		.offset = SZ_512K + SZ_512K + SZ_512K,
+	},
+};
+
+static const struct flash_platform_data dreamplug_spi_slave_data = {
+	.type		= "mx25l1606e",
+	.name		= "spi_flash",
+	.parts		= dreamplug_partitions,
+	.nr_parts	= ARRAY_SIZE(dreamplug_partitions),
+};
+
+static struct spi_board_info __initdata dreamplug_spi_slave_info[] = {
+	{
+		.modalias	= "m25p80",
+		.platform_data	= &dreamplug_spi_slave_data,
+		.irq		= -1,
+		.max_speed_hz	= 50000000,
+		.bus_num	= 0,
+		.chip_select	= 0,
+	},
+};
+
+static struct mv643xx_eth_platform_data dreamplug_ge00_data = {
+	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
+};
+
+static struct mv643xx_eth_platform_data dreamplug_ge01_data = {
+	.phy_addr	= MV643XX_ETH_PHY_ADDR(1),
+};
+
+static struct mv_sata_platform_data dreamplug_sata_data = {
+	.n_ports	= 1,
+};
+
+static struct mvsdio_platform_data dreamplug_mvsdio_data = {
+	/* unfortunately the CD signal has not been connected */
+};
+
+static struct gpio_led dreamplug_led_pins[] = {
+	{
+		.name			= "dreamplug:blue:bluetooth",
+		.gpio			= 47,
+		.active_low		= 1,
+	},
+	{
+		.name			= "dreamplug:green:wifi",
+		.gpio			= 48,
+		.active_low		= 1,
+	},
+	{
+		.name			= "dreamplug:green:wifi_ap",
+		.gpio			= 49,
+		.active_low		= 1,
+	},
+};
+
+static struct gpio_led_platform_data dreamplug_led_data = {
+	.leds		= dreamplug_led_pins,
+	.num_leds	= ARRAY_SIZE(dreamplug_led_pins),
+};
+
+static struct platform_device dreamplug_leds = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data	= &dreamplug_led_data,
+	}
+};
+
+static unsigned int dreamplug_mpp_config[] __initdata = {
+	MPP0_SPI_SCn,
+	MPP1_SPI_MOSI,
+	MPP2_SPI_SCK,
+	MPP3_SPI_MISO,
+	MPP47_GPIO,	/* Bluetooth LED */
+	MPP48_GPIO,	/* Wifi LED */
+	MPP49_GPIO,	/* Wifi AP LED */
+	0
+};
+
+void __init dreamplug_init(void)
+{
+	/*
+	 * Basic setup. Needs to be called early.
+	 */
+	kirkwood_mpp_conf(dreamplug_mpp_config);
+
+	spi_register_board_info(dreamplug_spi_slave_info,
+				ARRAY_SIZE(dreamplug_spi_slave_info));
+	kirkwood_spi_init();
+
+	kirkwood_ehci_init();
+	kirkwood_ge00_init(&dreamplug_ge00_data);
+	kirkwood_ge01_init(&dreamplug_ge01_data);
+	kirkwood_sata_init(&dreamplug_sata_data);
+	kirkwood_sdio_init(&dreamplug_mvsdio_data);
+
+	platform_device_register(&dreamplug_leds);
+}