---

yaml
---
r: 355096
b: refs/heads/master
c: 9c95bb6
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: def1820d25fa93cf5fca10bf45f22cdb11be41f2
+refs/heads/master: 9c95bb6f25ff802081125f24bf0c756252fa27b2

trunk/drivers/w1/masters/ds2482.c

@@ -51,10 +51,10 @@
  * The top 4 bits always read 0.
  * To write, the top nibble must be the 1's compl. of the low nibble.
  */
-#define DS2482_REG_CFG_1WS		0x08
-#define DS2482_REG_CFG_SPU		0x04
-#define DS2482_REG_CFG_PPM		0x02
-#define DS2482_REG_CFG_APU		0x01
+#define DS2482_REG_CFG_1WS		0x08	/* 1-wire speed */
+#define DS2482_REG_CFG_SPU		0x04	/* strong pull-up */
+#define DS2482_REG_CFG_PPM		0x02	/* presence pulse masking */
+#define DS2482_REG_CFG_APU		0x01	/* active pull-up */
 
 
 /**
@@ -131,6 +131,17 @@ struct ds2482_data {
 };
 
 
+/**
+ * Helper to calculate values for configuration register
+ * @param conf the raw config value
+ * @return the value w/ complements that can be written to register
+ */
+static inline u8 ds2482_calculate_config(u8 conf)
+{
+	return conf | ((~conf & 0x0f) << 4);
+}
+
+
 /**
  * Sets the read pointer.
  * @param pdev		The ds2482 client pointer
@@ -399,14 +410,40 @@ static u8 ds2482_w1_reset_bus(void *data)
 		/* If the chip did reset since detect, re-config it */
 		if (err & DS2482_REG_STS_RST)
 			ds2482_send_cmd_data(pdev, DS2482_CMD_WRITE_CONFIG,
-					     0xF0);
+					     ds2482_calculate_config(0x00));
 	}
 
 	mutex_unlock(&pdev->access_lock);
 
 	return retval;
 }
 
+static u8 ds2482_w1_set_pullup(void *data, int delay)
+{
+	struct ds2482_w1_chan *pchan = data;
+	struct ds2482_data    *pdev = pchan->pdev;
+	u8 retval = 1;
+
+	/* if delay is non-zero activate the pullup,
+	 * the strong pullup will be automatically deactivated
+	 * by the master, so do not explicitly deactive it
+	 */
+	if (delay) {
+		/* both waits are crucial, otherwise devices might not be
+		 * powered long enough, causing e.g. a w1_therm sensor to
+		 * provide wrong conversion results
+		 */
+		ds2482_wait_1wire_idle(pdev);
+		/* note: it seems like both SPU and APU have to be set! */
+		retval = ds2482_send_cmd_data(pdev, DS2482_CMD_WRITE_CONFIG,
+			ds2482_calculate_config(DS2482_REG_CFG_SPU |
+						DS2482_REG_CFG_APU));
+		ds2482_wait_1wire_idle(pdev);
+	}
+
+	return retval;
+}
+
 
 static int ds2482_probe(struct i2c_client *client,
 			const struct i2c_device_id *id)
@@ -452,7 +489,8 @@ static int ds2482_probe(struct i2c_client *client,
 		data->w1_count = 8;
 
 	/* Set all config items to 0 (off) */
-	ds2482_send_cmd_data(data, DS2482_CMD_WRITE_CONFIG, 0xF0);
+	ds2482_send_cmd_data(data, DS2482_CMD_WRITE_CONFIG,
+		ds2482_calculate_config(0x00));
 
 	mutex_init(&data->access_lock);
 
@@ -468,6 +506,7 @@ static int ds2482_probe(struct i2c_client *client,
 		data->w1_ch[idx].w1_bm.touch_bit  = ds2482_w1_touch_bit;
 		data->w1_ch[idx].w1_bm.triplet    = ds2482_w1_triplet;
 		data->w1_ch[idx].w1_bm.reset_bus  = ds2482_w1_reset_bus;
+		data->w1_ch[idx].w1_bm.set_pullup = ds2482_w1_set_pullup;
 
 		err = w1_add_master_device(&data->w1_ch[idx].w1_bm);
 		if (err) {