Merge branch 'omap-serial' of git://git.linaro.org/people/rmk/linux-arm

Pull ARM OMAP serial updates from Russell King:
 "This series is a major reworking of the OMAP serial driver code fixing
  various bugs in the hardware-assisted flow control, extending up into
  serial_core for a couple of issues.  These fixes have been done as a
  set of progressive changes and transformations in the hope that no new
  bugs will be introduced by this series.

  The problems are many-fold, from the driver not being informed about
  updated settings, to the driver not knowing what the intentions of the
  upper layers are.

  The first four patches tackle the serial_core layer, allowing it to
  provide the necessary information to drivers, and the remaining
  patches allow the OMAP serial driver to take advantage of this.

  This brings hardware assisted RTS/CTS and XON/OFF flow control into a
  useful state.

  These patches have been in linux-next for most of the last cycle;
  indeed they predate the previous merge window.  They've also been
  posted to the OMAP people."

* 'omap-serial' of git://git.linaro.org/people/rmk/linux-arm: (21 commits)
  SERIAL: omap: fix hardware assisted flow control
  SERIAL: omap: simplify (2)
  SERIAL: omap: move xon/xoff setting earlier
  SERIAL: omap: always set TCR
  SERIAL: omap: simplify
  SERIAL: omap: don't read back LCR/MCR/EFR
  SERIAL: omap: serial_omap_configure_xonxoff() contents into set_termios
  SERIAL: omap: configure xon/xoff before setting modem control lines
  SERIAL: omap: remove OMAP_UART_SYSC_RESET and OMAP_UART_FIFO_CLR
  SERIAL: omap: move driver private definitions and structures to driver
  SERIAL: omap: remove 'irq_pending' bitfield
  SERIAL: omap: fix MCR TCRTLR bit handling
  SERIAL: omap: fix set_mctrl() breakage
  SERIAL: omap: no need to re-read EFR
  SERIAL: omap: remove setting of EFR SCD bit
  SERIAL: omap: allow hardware assisted IXANY mode to be disabled
  SERIAL: omap: allow hardware assisted rts/cts modes to be disabled
  SERIAL: core: add throttle/unthrottle callbacks for hardware assisted flow control
  SERIAL: core: add hardware assisted h/w flow control support
  SERIAL: core: add hardware assisted s/w flow control support
  ...

Conflicts:
	drivers/tty/serial/omap-serial.c

arch/arm/plat-omap/include/plat/omap-serial.h

@@ -30,35 +30,6 @@
  */
 #define OMAP_SERIAL_NAME	"ttyO"
 
-#define OMAP_MODE13X_SPEED	230400
-
-#define OMAP_UART_SCR_TX_EMPTY	0x08
-
-/* WER = 0x7F
- * Enable module level wakeup in WER reg
- */
-#define OMAP_UART_WER_MOD_WKUP	0X7F
-
-/* Enable XON/XOFF flow control on output */
-#define OMAP_UART_SW_TX		0x04
-
-/* Enable XON/XOFF flow control on input */
-#define OMAP_UART_SW_RX		0x04
-
-#define OMAP_UART_SYSC_RESET	0X07
-#define OMAP_UART_TCR_TRIG	0X0F
-#define OMAP_UART_SW_CLR	0XF0
-#define OMAP_UART_FIFO_CLR	0X06
-
-#define OMAP_UART_DMA_CH_FREE	-1
-
-#define OMAP_MAX_HSUART_PORTS	6
-
-#define MSR_SAVE_FLAGS		UART_MSR_ANY_DELTA
-
-#define UART_ERRATA_i202_MDR1_ACCESS	BIT(0)
-#define UART_ERRATA_i291_DMA_FORCEIDLE	BIT(1)
-
 struct omap_uart_port_info {
 	bool			dma_enabled;	/* To specify DMA Mode */
 	unsigned int		uartclk;	/* UART clock rate */
@@ -77,30 +48,4 @@ struct omap_uart_port_info {
 	void (*enable_wakeup)(struct device *, bool);
 };
 
-struct uart_omap_dma {
-	u8			uart_dma_tx;
-	u8			uart_dma_rx;
-	int			rx_dma_channel;
-	int			tx_dma_channel;
-	dma_addr_t		rx_buf_dma_phys;
-	dma_addr_t		tx_buf_dma_phys;
-	unsigned int		uart_base;
-	/*
-	 * Buffer for rx dma.It is not required for tx because the buffer
-	 * comes from port structure.
-	 */
-	unsigned char		*rx_buf;
-	unsigned int		prev_rx_dma_pos;
-	int			tx_buf_size;
-	int			tx_dma_used;
-	int			rx_dma_used;
-	spinlock_t		tx_lock;
-	spinlock_t		rx_lock;
-	/* timer to poll activity on rx dma */
-	struct timer_list	rx_timer;
-	unsigned int		rx_buf_size;
-	unsigned int		rx_poll_rate;
-	unsigned int		rx_timeout;
-};
-
 #endif /* __OMAP_SERIAL_H__ */