---

yaml
---
r: 373907
b: refs/heads/master
c: 7c3c1b8
h: refs/heads/master
i:
  373905: ca09f97
  373903: df91c6b
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: f6940610c76e9a6dbb23cef51b64fd48877b68df
+refs/heads/master: 7c3c1b8c90e0f226610b9932cd66678d99e42176

trunk/Documentation/devicetree/bindings/gpio/gpio.txt

@@ -98,7 +98,7 @@ announce the pinrange to the pin ctrl subsystem. For example,
 		compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank";
 		reg = <0x1460 0x18>;
 		gpio-controller;
-		gpio-ranges = <&pinctrl1 0 20 10>, <&pinctrl2 10 50 20>;
+		gpio-ranges = <&pinctrl1 20 10>, <&pinctrl2 50 20>;
 
     }
 
@@ -107,8 +107,8 @@ where,
 
    Next values specify the base pin and number of pins for the range
    handled by 'qe_pio_e' gpio. In the given example from base pin 20 to
-   pin 29 under pinctrl1 with gpio offset 0 and pin 50 to pin 69 under
-   pinctrl2 with gpio offset 10 is handled by this gpio controller.
+   pin 29 under pinctrl1 and pin 50 to pin 69 under pinctrl2 is handled
+   by this gpio controller.
 
 The pinctrl node must have "#gpio-range-cells" property to show number of
 arguments to pass with phandle from gpio controllers node.

trunk/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt

@@ -1,9 +1,7 @@
 One-register-per-pin type device tree based pinctrl driver
 
 Required properties:
-- compatible : "pinctrl-single" or "pinconf-single".
-  "pinctrl-single" means that pinconf isn't supported.
-  "pinconf-single" means that generic pinconf is supported.
+- compatible : "pinctrl-single"
 
 - reg : offset and length of the register set for the mux registers
 
@@ -16,61 +14,9 @@ Optional properties:
 - pinctrl-single,function-off : function off mode for disabled state if
   available and same for all registers; if not specified, disabling of
   pin functions is ignored
-
 - pinctrl-single,bit-per-mux : boolean to indicate that one register controls
   more than one pin
 
-- pinctrl-single,drive-strength : array of value that are used to configure
-  drive strength in the pinmux register. They're value of drive strength
-  current and drive strength mask.
-
-		/* drive strength current, mask */
-		pinctrl-single,power-source = <0x30 0xf0>;
-
-- pinctrl-single,bias-pullup : array of value that are used to configure the
-  input bias pullup in the pinmux register.
-
-		/* input, enabled pullup bits, disabled pullup bits, mask */
-		pinctrl-single,bias-pullup = <0 1 0 1>;
-
-- pinctrl-single,bias-pulldown : array of value that are used to configure the
-  input bias pulldown in the pinmux register.
-
-		/* input, enabled pulldown bits, disabled pulldown bits, mask */
-		pinctrl-single,bias-pulldown = <2 2 0 2>;
-
-  * Two bits to control input bias pullup and pulldown: User should use
-    pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. One bit means
-    pullup, and the other one bit means pulldown.
-  * Three bits to control input bias enable, pullup and pulldown. User should
-    use pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. Input bias
-    enable bit should be included in pullup or pulldown bits.
-  * Although driver could set PIN_CONFIG_BIAS_DISABLE, there's no property as
-    pinctrl-single,bias-disable. Because pinctrl single driver could implement
-    it by calling pulldown, pullup disabled.
-
-- pinctrl-single,input-schmitt : array of value that are used to configure
-  input schmitt in the pinmux register. In some silicons, there're two input
-  schmitt value (rising-edge & falling-edge) in the pinmux register.
-
-		/* input schmitt value, mask */
-		pinctrl-single,input-schmitt = <0x30 0x70>;
-
-- pinctrl-single,input-schmitt-enable : array of value that are used to
-  configure input schmitt enable or disable in the pinmux register.
-
-		/* input, enable bits, disable bits, mask */
-		pinctrl-single,input-schmitt-enable = <0x30 0x40 0 0x70>;
-
-- pinctrl-single,gpio-range : list of value that are used to configure a GPIO
-  range. They're value of subnode phandle, pin base in pinctrl device, pin
-  number in this range, GPIO function value of this GPIO range.
-  The number of parameters is depend on #pinctrl-single,gpio-range-cells
-  property.
-
-		/* pin base, nr pins & gpio function */
-		pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1>;
-
 This driver assumes that there is only one register for each pin (unless the
 pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as
 specified in the pinctrl-bindings.txt document in this directory.
@@ -96,20 +42,6 @@ Where 0xdc is the offset from the pinctrl register base address for the
 device pinctrl register, 0x18 is the desired value, and 0xff is the sub mask to
 be used when applying this change to the register.
 
-
-Optional sub-node: In case some pins could be configured as GPIO in the pinmux
-register, those pins could be defined as a GPIO range. This sub-node is required
-by pinctrl-single,gpio-range property.
-
-Required properties in sub-node:
-- #pinctrl-single,gpio-range-cells : the number of parameters after phandle in
-  pinctrl-single,gpio-range property.
-
-	range: gpio-range {
-		#pinctrl-single,gpio-range-cells = <3>;
-	};
-
-
 Example:
 
 /* SoC common file */
@@ -144,29 +76,6 @@ control_devconf0: pinmux@48002274 {
 	pinctrl-single,function-mask = <0x5F>;
 };
 
-/* third controller instance for pins in gpio domain */
-pmx_gpio: pinmux@d401e000 {
-	compatible = "pinconf-single";
-	reg = <0xd401e000 0x0330>;
-	#address-cells = <1>;
-	#size-cells = <1>;
-	ranges;
-
-	pinctrl-single,register-width = <32>;
-	pinctrl-single,function-mask = <7>;
-
-	/* sparse GPIO range could be supported */
-	pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1
-				&range 12 1 0 &range 13 29 1
-				&range 43 1 0 &range 44 49 1
-				&range 94 1 1 &range 96 2 1>;
-
-	range: gpio-range {
-		#pinctrl-single,gpio-range-cells = <3>;
-	};
-};
-
-
 /* board specific .dts file */
 
 &pmx_core {
@@ -187,15 +96,6 @@ pmx_gpio: pinmux@d401e000 {
 		>;
 	};
 
-	uart0_pins: pinmux_uart0_pins {
-		pinctrl-single,pins = <
-			0x208 0		/* UART0_RXD (IOCFG138) */
-			0x20c 0		/* UART0_TXD (IOCFG139) */
-		>;
-		pinctrl-single,bias-pulldown = <0 2 2>;
-		pinctrl-single,bias-pullup = <0 1 1>;
-	};
-
 	/* map uart2 pins */
 	uart2_pins: pinmux_uart2_pins {
 		pinctrl-single,pins = <
@@ -222,11 +122,6 @@ pmx_gpio: pinmux@d401e000 {
 
 };
 
-&uart1 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&uart0_pins>;
-};
-
 &uart2 {
        pinctrl-names = "default";
        pinctrl-0 = <&uart2_pins>;

trunk/Documentation/sound/alsa/ALSA-Configuration.txt

@@ -890,9 +890,8 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
     enable_msi	- Enable Message Signaled Interrupt (MSI) (default = off)
     power_save	- Automatic power-saving timeout (in second, 0 =
 		disable)
-    power_save_controller - Support runtime D3 of HD-audio controller
-		(-1 = on for supported chip (default), false = off,
-		 true = force to on even for unsupported hardware)
+    power_save_controller - Reset HD-audio controller in power-saving mode
+		(default = on)
     align_buffer_size - Force rounding of buffer/period sizes to multiples
     		      of 128 bytes. This is more efficient in terms of memory
 		      access but isn't required by the HDA spec and prevents

trunk/MAINTAINERS

@@ -5065,9 +5065,8 @@ S:	Maintained
 F:	drivers/net/ethernet/marvell/sk*
 
 MARVELL LIBERTAS WIRELESS DRIVER
-M:	Dan Williams <dcbw@redhat.com>
 L:	libertas-dev@lists.infradead.org
-S:	Maintained
+S:	Orphan
 F:	drivers/net/wireless/libertas/
 
 MARVELL MV643XX ETHERNET DRIVER
@@ -5569,6 +5568,7 @@ F:	include/uapi/linux/if_*
 F:	include/uapi/linux/netdevice.h
 
 NETXEN (1/10) GbE SUPPORT
+M:	Manish Chopra <manish.chopra@qlogic.com>
 M:	Sony Chacko <sony.chacko@qlogic.com>
 M:	Rajesh Borundia <rajesh.borundia@qlogic.com>
 L:	netdev@vger.kernel.org

trunk/Makefile

@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 9
 SUBLEVEL = 0
-EXTRAVERSION = -rc5
+EXTRAVERSION = -rc6
 NAME = Unicycling Gorilla
 
 # *DOCUMENTATION*

trunk/arch/alpha/Makefile

@@ -12,7 +12,7 @@ NM := $(NM) -B
 
 LDFLAGS_vmlinux	:= -static -N #-relax
 CHECKFLAGS	+= -D__alpha__ -m64
-cflags-y	:= -pipe -mno-fp-regs -ffixed-8 -msmall-data
+cflags-y	:= -pipe -mno-fp-regs -ffixed-8
 cflags-y	+= $(call cc-option, -fno-jump-tables)
 
 cpuflags-$(CONFIG_ALPHA_EV4)		:= -mcpu=ev4

trunk/arch/alpha/include/asm/floppy.h

@@ -26,7 +26,7 @@
 #define fd_disable_irq()        disable_irq(FLOPPY_IRQ)
 #define fd_cacheflush(addr,size) /* nothing */
 #define fd_request_irq()        request_irq(FLOPPY_IRQ, floppy_interrupt,\
-					    IRQF_DISABLED, "floppy", NULL)
+					    0, "floppy", NULL)
 #define fd_free_irq()           free_irq(FLOPPY_IRQ, NULL)
 
 #ifdef CONFIG_PCI

trunk/arch/alpha/kernel/irq.c

@@ -117,13 +117,6 @@ handle_irq(int irq)
 		return;
 	}
 
-	/*
-	 * From here we must proceed with IPL_MAX. Note that we do not
-	 * explicitly enable interrupts afterwards - some MILO PALcode
-	 * (namely LX164 one) seems to have severe problems with RTI
-	 * at IPL 0.
-	 */
-	local_irq_disable();
 	irq_enter();
 	generic_handle_irq_desc(irq, desc);
 	irq_exit();

trunk/arch/alpha/kernel/irq_alpha.c

@@ -45,6 +45,14 @@ do_entInt(unsigned long type, unsigned long vector,
 	  unsigned long la_ptr, struct pt_regs *regs)
 {
 	struct pt_regs *old_regs;
+
+	/*
+	 * Disable interrupts during IRQ handling.
+	 * Note that there is no matching local_irq_enable() due to
+	 * severe problems with RTI at IPL0 and some MILO PALcode
+	 * (namely LX164).
+	 */
+	local_irq_disable();
 	switch (type) {
 	case 0:
 #ifdef CONFIG_SMP
@@ -62,7 +70,6 @@ do_entInt(unsigned long type, unsigned long vector,
 	  {
 		long cpu;
 
-		local_irq_disable();
 		smp_percpu_timer_interrupt(regs);
 		cpu = smp_processor_id();
 		if (cpu != boot_cpuid) {
@@ -222,7 +229,6 @@ process_mcheck_info(unsigned long vector, unsigned long la_ptr,
 
 struct irqaction timer_irqaction = {
 	.handler	= timer_interrupt,
-	.flags		= IRQF_DISABLED,
 	.name		= "timer",
 };
 

trunk/arch/alpha/kernel/sys_nautilus.c

@@ -188,6 +188,10 @@ nautilus_machine_check(unsigned long vector, unsigned long la_ptr)
 extern void free_reserved_mem(void *, void *);
 extern void pcibios_claim_one_bus(struct pci_bus *);
 
+static struct resource irongate_io = {
+	.name	= "Irongate PCI IO",
+	.flags	= IORESOURCE_IO,
+};
 static struct resource irongate_mem = {
 	.name	= "Irongate PCI MEM",
 	.flags	= IORESOURCE_MEM,
@@ -209,6 +213,7 @@ nautilus_init_pci(void)
 
 	irongate = pci_get_bus_and_slot(0, 0);
 	bus->self = irongate;
+	bus->resource[0] = &irongate_io;
 	bus->resource[1] = &irongate_mem;
 
 	pci_bus_size_bridges(bus);

trunk/arch/alpha/kernel/sys_titan.c

@@ -280,15 +280,15 @@ titan_late_init(void)
 	 * all reported to the kernel as machine checks, so the handler
 	 * is a nop so it can be called to count the individual events.
 	 */
-	titan_request_irq(63+16, titan_intr_nop, IRQF_DISABLED,
+	titan_request_irq(63+16, titan_intr_nop, 0,
 		    "CChip Error", NULL);
-	titan_request_irq(62+16, titan_intr_nop, IRQF_DISABLED,
+	titan_request_irq(62+16, titan_intr_nop, 0,
 		    "PChip 0 H_Error", NULL);
-	titan_request_irq(61+16, titan_intr_nop, IRQF_DISABLED,
+	titan_request_irq(61+16, titan_intr_nop, 0,
 		    "PChip 1 H_Error", NULL);
-	titan_request_irq(60+16, titan_intr_nop, IRQF_DISABLED,
+	titan_request_irq(60+16, titan_intr_nop, 0,
 		    "PChip 0 C_Error", NULL);
-	titan_request_irq(59+16, titan_intr_nop, IRQF_DISABLED,
+	titan_request_irq(59+16, titan_intr_nop, 0,
 		    "PChip 1 C_Error", NULL);
 
 	/* 
@@ -348,9 +348,9 @@ privateer_init_pci(void)
 	 * Hook a couple of extra err interrupts that the
 	 * common titan code won't.
 	 */
-	titan_request_irq(53+16, titan_intr_nop, IRQF_DISABLED,
+	titan_request_irq(53+16, titan_intr_nop, 0,
 		    "NMI", NULL);
-	titan_request_irq(50+16, titan_intr_nop, IRQF_DISABLED,
+	titan_request_irq(50+16, titan_intr_nop, 0,
 		    "Temperature Warning", NULL);
 
 	/*

trunk/arch/arm/Kconfig

@@ -723,7 +723,7 @@ config ARCH_SHMOBILE
 	select MULTI_IRQ_HANDLER
 	select NEED_MACH_MEMORY_H
 	select NO_IOPORT
-	select PINCTRL if ARCH_WANT_OPTIONAL_GPIOLIB
+	select PINCTRL
 	select PM_GENERIC_DOMAINS if PM
 	select SPARSE_IRQ
 	help
@@ -1183,9 +1183,9 @@ config ARM_NR_BANKS
 	default 8
 
 config IWMMXT
-	bool "Enable iWMMXt support"
+	bool "Enable iWMMXt support" if !CPU_PJ4
 	depends on CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_PJ4
-	default y if PXA27x || PXA3xx || ARCH_MMP
+	default y if PXA27x || PXA3xx || ARCH_MMP || CPU_PJ4
 	help
 	  Enable support for iWMMXt context switching at run time if
 	  running on a CPU that supports it.
@@ -1439,6 +1439,16 @@ config ARM_ERRATA_775420
 	 to deadlock. This workaround puts DSB before executing ISB if
 	 an abort may occur on cache maintenance.
 
+config ARM_ERRATA_798181
+	bool "ARM errata: TLBI/DSB failure on Cortex-A15"
+	depends on CPU_V7 && SMP
+	help
+	  On Cortex-A15 (r0p0..r3p2) the TLBI*IS/DSB operations are not
+	  adequately shooting down all use of the old entries. This
+	  option enables the Linux kernel workaround for this erratum
+	  which sends an IPI to the CPUs that are running the same ASID
+	  as the one being invalidated.
+
 endmenu
 
 source "arch/arm/common/Kconfig"
@@ -1593,7 +1603,6 @@ config HAVE_ARM_ARCH_TIMER
 config HAVE_ARM_TWD
 	bool
 	depends on SMP
-	select CLKSRC_OF if OF
 	help
 	  This options enables support for the ARM timer and watchdog unit