Merge branch 'next/dt' into next/multiplatform

* next/dt: (182 commits)
  ARM: tegra: Add Avionic Design Tamonten Evaluation Carrier support
  ARM: tegra: Add Avionic Design Medcom-Wide support
  ARM: tegra: Add Avionic Design Plutux support
  ARM: tegra: Add Avionic Design Tamonten support
  ARM: tegra: dts: Add pwm label
  ARM: dt: tegra: whistler: configure power off
  ARM: mxs: m28evk: Disable OCOTP OUI loading
  ARM: imx6q: use pll2_pfd2_396m as the enfc_sel's parent
  ARM: dts: imx6q-sabrelite: add usbotg pinctrl support
  ARM: dts: imx23-olinuxino: Add USB host support
  ARM: dts: imx6q-sabrelite: add usbmisc device
  ARM: dts: mx23: Add USB resources
  ARM: dts: mxs: Add ethernetX to macX aliases
  ARM: msm: Remove non-DT targets from 8960
  ARM: msm: Add DT support for 8960
  ARM: msm: Move io mapping prototypes to common.h
  ARM: msm: Rename board-msm8x60 to signify its DT only status
  ARM: msm: Make 8660 a DT only target
  ARM: msm: Move 8660 to DT timer
  ARM: msm: Add DT support to msm_timer
  ...

Documentation/devicetree/bindings/arm/mrvl/tauros2.txt

@@ -0,0 +1,17 @@
+* Marvell Tauros2 Cache
+
+Required properties:
+- compatible : Should be "marvell,tauros2-cache".
+- marvell,tauros2-cache-features : Specify the features supported for the
+  tauros2 cache.
+  The features including
+    CACHE_TAUROS2_PREFETCH_ON       (1 << 0)
+    CACHE_TAUROS2_LINEFILL_BURST8   (1 << 1)
+  The definition can be found at
+  arch/arm/include/asm/hardware/cache-tauros2.h
+
+Example:
+	L2: l2-cache {
+		compatible = "marvell,tauros2-cache";
+		marvell,tauros2-cache-features = <0x3>;
+	};

Documentation/devicetree/bindings/arm/msm/timer.txt

@@ -0,0 +1,38 @@
+* MSM Timer
+
+Properties:
+
+- compatible : Should at least contain "qcom,msm-timer". More specific
+  properties such as "qcom,msm-gpt" and "qcom,msm-dgt" specify a general
+  purpose timer and a debug timer respectively.
+
+- interrupts : Interrupt indicating a match event.
+
+- reg : Specifies the base address of the timer registers. The second region
+  specifies an optional register used to configure the clock divider.
+
+- clock-frequency : The frequency of the timer in Hz.
+
+Optional:
+
+- cpu-offset : per-cpu offset used when the timer is accessed without the
+  CPU remapping facilities. The offset is cpu-offset * cpu-nr.
+
+Example:
+
+       timer@200a004 {
+               compatible = "qcom,msm-gpt", "qcom,msm-timer";
+               interrupts = <1 2 0x301>;
+               reg = <0x0200a004 0x10>;
+               clock-frequency = <32768>;
+               cpu-offset = <0x40000>;
+       };
+
+       timer@200a024 {
+               compatible = "qcom,msm-dgt", "qcom,msm-timer";
+               interrupts = <1 3 0x301>;
+               reg = <0x0200a024 0x10>,
+                     <0x0200a034 0x4>;
+               clock-frequency = <6750000>;
+               cpu-offset = <0x40000>;
+       };

Documentation/devicetree/bindings/arm/omap/omap.txt

@@ -36,6 +36,9 @@ Boards:
 - OMAP3 BeagleBoard : Low cost community board
   compatible = "ti,omap3-beagle", "ti,omap3"
 
+- OMAP3 Tobi with Overo : Commercial expansion board with daughter board
+  compatible = "ti,omap3-tobi", "ti,omap3-overo", "ti,omap3"
+
 - OMAP4 SDP : Software Developement Board
   compatible = "ti,omap4-sdp", "ti,omap4430"
 

Documentation/devicetree/bindings/clock/imx23-clock.txt

@@ -0,0 +1,76 @@
+* Clock bindings for Freescale i.MX23
+
+Required properties:
+- compatible: Should be "fsl,imx23-clkctrl"
+- reg: Address and length of the register set
+- #clock-cells: Should be <1>
+
+The clock consumer should specify the desired clock by having the clock
+ID in its "clocks" phandle cell.  The following is a full list of i.MX23
+clocks and IDs.
+
+	Clock		ID
+	------------------
+	ref_xtal	0
+	pll		1
+	ref_cpu		2
+	ref_emi		3
+	ref_pix		4
+	ref_io		5
+	saif_sel	6
+	lcdif_sel	7
+	gpmi_sel	8
+	ssp_sel		9
+	emi_sel		10
+	cpu		11
+	etm_sel		12
+	cpu_pll		13
+	cpu_xtal	14
+	hbus		15
+	xbus		16
+	lcdif_div	17
+	ssp_div		18
+	gpmi_div	19
+	emi_pll		20
+	emi_xtal	21
+	etm_div		22
+	saif_div	23
+	clk32k_div	24
+	rtc		25
+	adc		26
+	spdif_div	27
+	clk32k		28
+	dri		29
+	pwm		30
+	filt		31
+	uart		32
+	ssp		33
+	gpmi		34
+	spdif		35
+	emi		36
+	saif		37
+	lcdif		38
+	etm		39
+	usb		40
+	usb_pwr		41
+
+Examples:
+
+clks: clkctrl@80040000 {
+	compatible = "fsl,imx23-clkctrl";
+	reg = <0x80040000 0x2000>;
+	#clock-cells = <1>;
+	clock-output-names =
+		...
+		"uart",		/* 32 */
+		...
+		"end_of_list";
+};
+
+auart0: serial@8006c000 {
+	compatible = "fsl,imx23-auart";
+	reg = <0x8006c000 0x2000>;
+	interrupts = <24 25 23>;
+	clocks = <&clks 32>;
+	status = "disabled";
+};

Documentation/devicetree/bindings/clock/imx28-clock.txt

@@ -0,0 +1,99 @@
+* Clock bindings for Freescale i.MX28
+
+Required properties:
+- compatible: Should be "fsl,imx28-clkctrl"
+- reg: Address and length of the register set
+- #clock-cells: Should be <1>
+
+The clock consumer should specify the desired clock by having the clock
+ID in its "clocks" phandle cell.  The following is a full list of i.MX28
+clocks and IDs.
+
+	Clock		ID
+	------------------
+	ref_xtal	0
+	pll0		1
+	pll1		2
+	pll2		3
+	ref_cpu		4
+	ref_emi		5
+	ref_io0		6
+	ref_io1		7
+	ref_pix		8
+	ref_hsadc	9
+	ref_gpmi	10
+	saif0_sel	11
+	saif1_sel	12
+	gpmi_sel	13
+	ssp0_sel	14
+	ssp1_sel	15
+	ssp2_sel	16
+	ssp3_sel	17
+	emi_sel		18
+	etm_sel		19
+	lcdif_sel	20
+	cpu		21
+	ptp_sel		22
+	cpu_pll		23
+	cpu_xtal	24
+	hbus		25
+	xbus		26
+	ssp0_div	27
+	ssp1_div	28
+	ssp2_div	29
+	ssp3_div	30
+	gpmi_div	31
+	emi_pll		32
+	emi_xtal	33
+	lcdif_div	34
+	etm_div		35
+	ptp		36
+	saif0_div	37
+	saif1_div	38
+	clk32k_div	39
+	rtc		40
+	lradc		41
+	spdif_div	42
+	clk32k		43
+	pwm		44
+	uart		45
+	ssp0		46
+	ssp1		47
+	ssp2		48
+	ssp3		49
+	gpmi		50
+	spdif		51
+	emi		52
+	saif0		53
+	saif1		54
+	lcdif		55
+	etm		56
+	fec		57
+	can0		58
+	can1		59
+	usb0		60
+	usb1		61
+	usb0_pwr	62
+	usb1_pwr	63
+	enet_out	64
+
+Examples:
+
+clks: clkctrl@80040000 {
+	compatible = "fsl,imx28-clkctrl";
+	reg = <0x80040000 0x2000>;
+	#clock-cells = <1>;
+	clock-output-names =
+		...
+		"uart",		/* 45 */
+		...
+		"end_of_list";
+};
+
+auart0: serial@8006a000 {
+	compatible = "fsl,imx28-auart", "fsl,imx23-auart";
+	reg = <0x8006a000 0x2000>;
+	interrupts = <112 70 71>;
+	clocks = <&clks 45>;
+	status = "disabled";
+};