---

yaml --- r: 126958 b: refs/heads/master c: bc37ae7 h: refs/heads/master v: v3
git-mirror · Jan 7, 2009 · ec4f5ce · ec4f5ce
1 parent de239f3
commit ec4f5ce
Show file tree

Hide file tree

Showing 283 changed files with 464 additions and 2,912 deletions.
diff --git a/[refs] b/[refs]
@@ -1,2 +1,2 @@
 ---
-refs/heads/master: fa7b906e7fef53b6c9eb3ecb8164b0a69e9e1a68
+refs/heads/master: bc37ae71207ca899efb93be1fe6b000366debc3a
diff --git a/trunk/CREDITS b/trunk/CREDITS
@@ -1681,7 +1681,7 @@ E: ajoshi@shell.unixbox.com
 D: fbdev hacking
 
 N: Jesper Juhl
-E: jj@chaosbits.net
+E: jesper.juhl@gmail.com
 D: Various fixes, cleanups and minor features all over the tree.
 D: Wrote initial version of the hdaps driver (since passed on to others).
 S: Lemnosvej 1, 3.tv

diff --git a/trunk/Documentation/dell_rbu.txt b/trunk/Documentation/dell_rbu.txt
@@ -81,8 +81,8 @@ Until this step is completed the driver cannot be unloaded.
 Also echoing either mono ,packet or init in to image_type will free up the
 memory allocated by the driver.
 
-If a user by accident executes steps 1 and 3 above without executing step 2;
-it will make the /sys/class/firmware/dell_rbu/ entries disappear.
+If an user by accident executes steps 1 and 3 above without executing step 2;
+it will make the /sys/class/firmware/dell_rbu/ entries to disappear.
 The entries can be recreated by doing the following
 echo init > /sys/devices/platform/dell_rbu/image_type
 NOTE: echoing init in image_type does not change it original value.

diff --git a/trunk/Documentation/hwmon/abituguru-datasheet b/trunk/Documentation/hwmon/abituguru-datasheet
@@ -74,7 +74,7 @@ a sensor.
 Notice that some banks have both a read and a write address this is how the
 uGuru determines if a read from or a write to the bank is taking place, thus
 when reading you should always use the read address and when writing the
-write address. The write address is always one (1) more than the read address.
+write address. The write address is always one (1) more then the read address.
 
 
 uGuru ready
@@ -224,7 +224,7 @@ Bit 3: Beep if alarm							(RW)
 Bit 4: 1 if alarm cause measured temp is over the warning threshold	(R)
 Bit 5: 1 if alarm cause measured volt is over the max threshold		(R)
 Bit 6: 1 if alarm cause measured volt is under the min threshold	(R)
-Bit 7: Volt sensor: Shutdown if alarm persist for more than 4 seconds	(RW)
+Bit 7: Volt sensor: Shutdown if alarm persist for more then 4 seconds	(RW)
        Temp sensor: Shutdown if temp is over the shutdown threshold	(RW)
 
 *  This bit is only honored/used by the uGuru if a temp sensor is connected
@@ -293,7 +293,7 @@ Byte 0:
 Alarm behaviour for the selected sensor. A 1 enables the described behaviour.
 Bit 0: Give an alarm if measured rpm is under the min threshold	(RW)
 Bit 3: Beep if alarm						(RW)
-Bit 7: Shutdown if alarm persist for more than 4 seconds	(RW)
+Bit 7: Shutdown if alarm persist for more then 4 seconds	(RW)
 
 Byte 1:
 min threshold (scale as bank 0x26)

diff --git a/trunk/Documentation/laptops/thinkpad-acpi.txt b/trunk/Documentation/laptops/thinkpad-acpi.txt
@@ -1475,7 +1475,7 @@ Sysfs interface changelog:
 
 0x020100:	Marker for thinkpad-acpi with hot key NVRAM polling
 		support.  If you must, use it to know you should not
-		start a userspace NVRAM poller (allows to detect when
+		start an userspace NVRAM poller (allows to detect when
 		NVRAM is compiled out by the user because it is
 		unneeded/undesired in the first place).
 0x020101:	Marker for thinkpad-acpi with hot key NVRAM polling

diff --git a/trunk/Documentation/networking/rxrpc.txt b/trunk/Documentation/networking/rxrpc.txt
@@ -540,7 +540,7 @@ A client would issue an operation by:
      MSG_MORE should be set in msghdr::msg_flags on all but the last part of
      the request.  Multiple requests may be made simultaneously.
 
-     If a call is intended to go to a destination other than the default
+     If a call is intended to go to a destination other then the default
      specified through connect(), then msghdr::msg_name should be set on the
      first request message of that call.
 

diff --git a/trunk/Documentation/networking/tuntap.txt b/trunk/Documentation/networking/tuntap.txt
@@ -118,7 +118,7 @@ As mentioned above, main purpose of TUN/TAP driver is tunneling.
 It is used by VTun (http://vtun.sourceforge.net).
 
 Another interesting application using TUN/TAP is pipsecd
-(http://perso.enst.fr/~beyssac/pipsec/), a userspace IPSec
+(http://perso.enst.fr/~beyssac/pipsec/), an userspace IPSec
 implementation that can use complete kernel routing (unlike FreeS/WAN).
 
 3. How does Virtual network device actually work ? 

diff --git a/trunk/Documentation/scsi/ChangeLog.lpfc b/trunk/Documentation/scsi/ChangeLog.lpfc
@@ -733,7 +733,7 @@ Changes from 20040920 to 20041018
 	  I/O completion path a little more, especially taking care of
 	  fast-pathing the non-error case.  Also removes tons of dead
 	  members and defines from lpfc_scsi.h - e.g. lpfc_target is down
-	  to nothing more than the lpfc_nodelist pointer.
+	  to nothing more then the lpfc_nodelist pointer.
 	* Added binary sysfs file to issue mbox commands
 	* Replaced #if __BIG_ENDIAN with #if __BIG_ENDIAN_BITFIELD for
 	  compatibility with the user space applications.

diff --git a/trunk/Documentation/scsi/ChangeLog.ncr53c8xx b/trunk/Documentation/scsi/ChangeLog.ncr53c8xx
@@ -19,7 +19,7 @@ Sun Sep 24 21:30 2000 Gerard Roudier (groudier@club-internet.fr)
 
 Wed Jul 26 23:30 2000 Gerard Roudier (groudier@club-internet.fr)
 	* version ncr53c8xx-3.4.1
-	- Provide OpenFirmware path through the proc FS on PPC.
+	- Provide OpenFirmare path through the proc FS on PPC.
 	- Remove trailing argument #2 from a couple of #undefs.
 
 Sun Jul 09 16:30 2000 Gerard Roudier (groudier@club-internet.fr)

diff --git a/trunk/Documentation/scsi/ChangeLog.sym53c8xx b/trunk/Documentation/scsi/ChangeLog.sym53c8xx
@@ -81,7 +81,7 @@ Sun Sep 24 21:30 2000 Gerard Roudier (groudier@club-internet.fr)
 
 Wed Jul 26 23:30 2000 Gerard Roudier (groudier@club-internet.fr)
 	* version sym53c8xx-1.7.1
-	- Provide OpenFirmware path through the proc FS on PPC.
+	- Provide OpenFirmare path through the proc FS on PPC.
 	- Download of on-chip SRAM using memcpy_toio() doesn't work 
 	  on PPC. Restore previous method (MEMORY MOVE from SCRIPTS).
 	- Remove trailing argument #2 from a couple of #undefs.

diff --git a/trunk/MAINTAINERS b/trunk/MAINTAINERS
@@ -4229,10 +4229,9 @@ L:	tpmdd-devel@lists.sourceforge.net (moderated for non-subscribers)
 S:	Maintained
 
 TRIVIAL PATCHES
-P:	Jiri Kosina
+P:	Jesper Juhl
 M:	trivial@kernel.org
 L:	linux-kernel@vger.kernel.org
-T:	git kernel.org:/pub/scm/linux/kernel/git/jikos/trivial.git
 S:	Maintained
 
 TTY LAYER

diff --git a/trunk/Makefile b/trunk/Makefile
@@ -1008,7 +1008,7 @@ define check-symlink
 endef
 
 # We create the target directory of the symlink if it does
-# not exist so the test in check-symlink works and we have a
+# not exist so the test in chack-symlink works and we have a
 # directory for generated filesas used by some architectures.
 define create-symlink
 	if [ ! -L include/asm ]; then                                      \

diff --git a/trunk/arch/avr32/Kconfig b/trunk/arch/avr32/Kconfig
@@ -122,24 +122,6 @@ config BOARD_ATNGW100
 	bool "ATNGW100 Network Gateway"
 	select CPU_AT32AP7000
 
-config BOARD_HAMMERHEAD
-	bool "Hammerhead board"
-	select CPU_AT32AP7000
-	select USB_ARCH_HAS_HCD
-	help
-	  The Hammerhead platform is built around a AVR32 32-bit microcontroller from Atmel.
-	  It offers versatile peripherals, such as ethernet, usb device, usb host etc.
-
-	  The board also incooperates a power supply and is a Power over Ethernet (PoE) Powered
-	  Device (PD).
-
-	  Additonally, a Cyclone III FPGA from Altera is integrated on the board. The FPGA is
-	  mapped into the 32-bit AVR memory bus. The FPGA offers two DDR2 SDRAM interfaces, which
-	  will cover even the most exceptional need of memory bandwidth. Together with the onboard
-	  video decoder the board is ready for video processing.
-
-	  For more information see: http://www.miromico.com/hammerhead
-
 config BOARD_FAVR_32
 	bool "Favr-32 LCD-board"
 	select CPU_AT32AP7000
@@ -151,7 +133,6 @@ endchoice
 
 source "arch/avr32/boards/atstk1000/Kconfig"
 source "arch/avr32/boards/atngw100/Kconfig"
-source "arch/avr32/boards/hammerhead/Kconfig"
 source "arch/avr32/boards/favr-32/Kconfig"
 
 choice

diff --git a/trunk/arch/avr32/Makefile b/trunk/arch/avr32/Makefile
@@ -33,7 +33,6 @@ head-y					+= arch/avr32/kernel/head.o
 core-y					+= $(machdirs)
 core-$(CONFIG_BOARD_ATSTK1000)		+= arch/avr32/boards/atstk1000/
 core-$(CONFIG_BOARD_ATNGW100)		+= arch/avr32/boards/atngw100/
-core-$(CONFIG_BOARD_HAMMERHEAD)		+= arch/avr32/boards/hammerhead/
 core-$(CONFIG_BOARD_FAVR_32)		+= arch/avr32/boards/favr-32/
 core-$(CONFIG_BOARD_MIMC200)		+= arch/avr32/boards/mimc200/
 core-$(CONFIG_LOADER_U_BOOT)		+= arch/avr32/boot/u-boot/

diff --git a/trunk/arch/avr32/boards/atngw100/setup.c b/trunk/arch/avr32/boards/atngw100/setup.c
@@ -19,8 +19,8 @@
 #include <linux/types.h>
 #include <linux/leds.h>
 #include <linux/spi/spi.h>
-#include <linux/atmel-mci.h>
 
+#include <asm/atmel-mci.h>
 #include <asm/io.h>
 #include <asm/setup.h>
 

diff --git a/trunk/arch/avr32/boards/atstk1000/atstk1002.c b/trunk/arch/avr32/boards/atstk1000/atstk1002.c
@@ -16,12 +16,12 @@
 #include <linux/types.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/at73c213.h>
-#include <linux/atmel-mci.h>
 
 #include <video/atmel_lcdc.h>
 
 #include <asm/io.h>
 #include <asm/setup.h>
+#include <asm/atmel-mci.h>
 
 #include <mach/at32ap700x.h>
 #include <mach/board.h>
@@ -287,7 +287,23 @@ static int __init atstk1002_init(void)
 	 * ATSTK1000 uses 32-bit SDRAM interface. Reserve the
 	 * SDRAM-specific pins so that nobody messes with them.
 	 */
-	at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL);
+	at32_reserve_pin(GPIO_PIN_PE(0));	/* DATA[16]	*/
+	at32_reserve_pin(GPIO_PIN_PE(1));	/* DATA[17]	*/
+	at32_reserve_pin(GPIO_PIN_PE(2));	/* DATA[18]	*/
+	at32_reserve_pin(GPIO_PIN_PE(3));	/* DATA[19]	*/
+	at32_reserve_pin(GPIO_PIN_PE(4));	/* DATA[20]	*/
+	at32_reserve_pin(GPIO_PIN_PE(5));	/* DATA[21]	*/
+	at32_reserve_pin(GPIO_PIN_PE(6));	/* DATA[22]	*/
+	at32_reserve_pin(GPIO_PIN_PE(7));	/* DATA[23]	*/
+	at32_reserve_pin(GPIO_PIN_PE(8));	/* DATA[24]	*/
+	at32_reserve_pin(GPIO_PIN_PE(9));	/* DATA[25]	*/
+	at32_reserve_pin(GPIO_PIN_PE(10));	/* DATA[26]	*/
+	at32_reserve_pin(GPIO_PIN_PE(11));	/* DATA[27]	*/
+	at32_reserve_pin(GPIO_PIN_PE(12));	/* DATA[28]	*/
+	at32_reserve_pin(GPIO_PIN_PE(13));	/* DATA[29]	*/
+	at32_reserve_pin(GPIO_PIN_PE(14));	/* DATA[30]	*/
+	at32_reserve_pin(GPIO_PIN_PE(15));	/* DATA[31]	*/
+	at32_reserve_pin(GPIO_PIN_PE(26));	/* SDCS		*/
 
 #ifdef CONFIG_BOARD_ATSTK1006
 	smc_set_timing(&nand_config, &nand_timing);

diff --git a/trunk/arch/avr32/boards/atstk1000/atstk1003.c b/trunk/arch/avr32/boards/atstk1000/atstk1003.c
@@ -17,9 +17,9 @@
 
 #include <linux/spi/at73c213.h>
 #include <linux/spi/spi.h>
-#include <linux/atmel-mci.h>
 
 #include <asm/setup.h>
+#include <asm/atmel-mci.h>
 
 #include <mach/at32ap700x.h>
 #include <mach/board.h>
@@ -131,7 +131,23 @@ static int __init atstk1003_init(void)
 	 * ATSTK1000 uses 32-bit SDRAM interface. Reserve the
 	 * SDRAM-specific pins so that nobody messes with them.
 	 */
-	at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL);
+	at32_reserve_pin(GPIO_PIN_PE(0));	/* DATA[16]	*/
+	at32_reserve_pin(GPIO_PIN_PE(1));	/* DATA[17]	*/
+	at32_reserve_pin(GPIO_PIN_PE(2));	/* DATA[18]	*/
+	at32_reserve_pin(GPIO_PIN_PE(3));	/* DATA[19]	*/
+	at32_reserve_pin(GPIO_PIN_PE(4));	/* DATA[20]	*/
+	at32_reserve_pin(GPIO_PIN_PE(5));	/* DATA[21]	*/
+	at32_reserve_pin(GPIO_PIN_PE(6));	/* DATA[22]	*/
+	at32_reserve_pin(GPIO_PIN_PE(7));	/* DATA[23]	*/
+	at32_reserve_pin(GPIO_PIN_PE(8));	/* DATA[24]	*/
+	at32_reserve_pin(GPIO_PIN_PE(9));	/* DATA[25]	*/
+	at32_reserve_pin(GPIO_PIN_PE(10));	/* DATA[26]	*/
+	at32_reserve_pin(GPIO_PIN_PE(11));	/* DATA[27]	*/
+	at32_reserve_pin(GPIO_PIN_PE(12));	/* DATA[28]	*/
+	at32_reserve_pin(GPIO_PIN_PE(13));	/* DATA[29]	*/
+	at32_reserve_pin(GPIO_PIN_PE(14));	/* DATA[30]	*/
+	at32_reserve_pin(GPIO_PIN_PE(15));	/* DATA[31]	*/
+	at32_reserve_pin(GPIO_PIN_PE(26));	/* SDCS		*/
 
 #ifdef	CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
 	at32_add_device_usart(1);

diff --git a/trunk/arch/avr32/boards/atstk1000/atstk1004.c b/trunk/arch/avr32/boards/atstk1000/atstk1004.c
@@ -17,11 +17,11 @@
 
 #include <linux/spi/at73c213.h>
 #include <linux/spi/spi.h>
-#include <linux/atmel-mci.h>
 
 #include <video/atmel_lcdc.h>
 
 #include <asm/setup.h>
+#include <asm/atmel-mci.h>
 
 #include <mach/at32ap700x.h>
 #include <mach/board.h>

diff --git a/trunk/arch/avr32/boards/favr-32/setup.c b/trunk/arch/avr32/boards/favr-32/setup.c
@@ -17,7 +17,6 @@
 #include <linux/linkage.h>
 #include <linux/gpio.h>
 #include <linux/leds.h>
-#include <linux/atmel-mci.h>
 #include <linux/atmel-pwm-bl.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
@@ -80,14 +79,6 @@ static struct spi_board_info __initdata spi1_board_info[] = {
 	},
 };
 
-static struct mci_platform_data __initdata mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= -ENODEV,
-		.wp_pin		= -ENODEV,
-	},
-};
-
 static struct fb_videomode __initdata lb104v03_modes[] = {
 	{
 		.name		= "640x480 @ 50",
@@ -316,10 +307,28 @@ static int __init favr32_init(void)
 	 * Favr-32 uses 32-bit SDRAM interface. Reserve the SDRAM-specific
 	 * pins so that nobody messes with them.
 	 */
-	at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL);
+	at32_reserve_pin(GPIO_PIN_PE(0));	/* DATA[16]	*/
+	at32_reserve_pin(GPIO_PIN_PE(1));	/* DATA[17]	*/
+	at32_reserve_pin(GPIO_PIN_PE(2));	/* DATA[18]	*/
+	at32_reserve_pin(GPIO_PIN_PE(3));	/* DATA[19]	*/
+	at32_reserve_pin(GPIO_PIN_PE(4));	/* DATA[20]	*/
+	at32_reserve_pin(GPIO_PIN_PE(5));	/* DATA[21]	*/
+	at32_reserve_pin(GPIO_PIN_PE(6));	/* DATA[22]	*/
+	at32_reserve_pin(GPIO_PIN_PE(7));	/* DATA[23]	*/
+	at32_reserve_pin(GPIO_PIN_PE(8));	/* DATA[24]	*/
+	at32_reserve_pin(GPIO_PIN_PE(9));	/* DATA[25]	*/
+	at32_reserve_pin(GPIO_PIN_PE(10));	/* DATA[26]	*/
+	at32_reserve_pin(GPIO_PIN_PE(11));	/* DATA[27]	*/
+	at32_reserve_pin(GPIO_PIN_PE(12));	/* DATA[28]	*/
+	at32_reserve_pin(GPIO_PIN_PE(13));	/* DATA[29]	*/
+	at32_reserve_pin(GPIO_PIN_PE(14));	/* DATA[30]	*/
+	at32_reserve_pin(GPIO_PIN_PE(15));	/* DATA[31]	*/
+	at32_reserve_pin(GPIO_PIN_PE(26));	/* SDCS		*/
 
 	at32_select_gpio(GPIO_PIN_PB(3), 0);	/* IRQ from ADS7843 */
 
+	at32_add_system_devices();
+
 	at32_add_device_usart(0);
 
 	set_hw_addr(at32_add_device_eth(0, &eth_data[0]));
@@ -330,7 +339,7 @@ static int __init favr32_init(void)
 
 	at32_add_device_pwm(1 << atmel_pwm_bl_pdata.pwm_channel);
 	at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info));
-	at32_add_device_mci(0, &mci0_data);
+	at32_add_device_mci(0, NULL);
 	at32_add_device_usba(0, NULL);
 	at32_add_device_lcdc(0, &favr32_lcdc_data, fbmem_start, fbmem_size, 0);
 

diff --git a/trunk/arch/avr32/boards/hammerhead/Kconfig b/trunk/arch/avr32/boards/hammerhead/Kconfig
diff --git a/trunk/arch/avr32/boards/hammerhead/Makefile b/trunk/arch/avr32/boards/hammerhead/Makefile