---

yaml
---
r: 103406
b: refs/heads/master
c: 2aec609
h: refs/heads/master
v: v3

[refs]

@@ -1,2 +1,2 @@
 ---
-refs/heads/master: 9076689ab07974a6f5d230fc241448f7a77e9078
+refs/heads/master: 2aec609fb45e84d65bc8eabc7b650bbecb1cc179

trunk/Documentation/feature-removal-schedule.txt

@@ -315,6 +315,18 @@ Who:	Matthew Wilcox <willy@linux.intel.com>
 
 ---------------------------
 
+What:	SCTP_GET_PEER_ADDRS_NUM_OLD, SCTP_GET_PEER_ADDRS_OLD,
+	SCTP_GET_LOCAL_ADDRS_NUM_OLD, SCTP_GET_LOCAL_ADDRS_OLD
+When: 	June 2009
+Why:    A newer version of the options have been introduced in 2005 that
+	removes the limitions of the old API.  The sctp library has been
+        converted to use these new options at the same time.  Any user
+	space app that directly uses the old options should convert to using
+	the new options.
+Who:	Vlad Yasevich <vladislav.yasevich@hp.com>
+
+---------------------------
+
 What:	CONFIG_THERMAL_HWMON
 When:	January 2009
 Why:	This option was introduced just to allow older lm-sensors userspace

trunk/Documentation/networking/bonding.txt

@@ -289,35 +289,73 @@ downdelay
 fail_over_mac
 
 	Specifies whether active-backup mode should set all slaves to
-	the same MAC address (the traditional behavior), or, when
-	enabled, change the bond's MAC address when changing the
-	active interface (i.e., fail over the MAC address itself).
-
-	Fail over MAC is useful for devices that cannot ever alter
-	their MAC address, or for devices that refuse incoming
-	broadcasts with their own source MAC (which interferes with
-	the ARP monitor).
-
-	The down side of fail over MAC is that every device on the
-	network must be updated via gratuitous ARP, vs. just updating
-	a switch or set of switches (which often takes place for any
-	traffic, not just ARP traffic, if the switch snoops incoming
-	traffic to update its tables) for the traditional method.  If
-	the gratuitous ARP is lost, communication may be disrupted.
-
-	When fail over MAC is used in conjuction with the mii monitor,
-	devices which assert link up prior to being able to actually
-	transmit and receive are particularly susecptible to loss of
-	the gratuitous ARP, and an appropriate updelay setting may be
-	required.
-
-	A value of 0 disables fail over MAC, and is the default.  A
-	value of 1 enables fail over MAC.  This option is enabled
-	automatically if the first slave added cannot change its MAC
-	address.  This option may be modified via sysfs only when no
-	slaves are present in the bond.
-
-	This option was added in bonding version 3.2.0.
+	the same MAC address at enslavement (the traditional
+	behavior), or, when enabled, perform special handling of the
+	bond's MAC address in accordance with the selected policy.
+
+	Possible values are:
+
+	none or 0
+
+		This setting disables fail_over_mac, and causes
+		bonding to set all slaves of an active-backup bond to
+		the same MAC address at enslavement time.  This is the
+		default.
+
+	active or 1
+
+		The "active" fail_over_mac policy indicates that the
+		MAC address of the bond should always be the MAC
+		address of the currently active slave.  The MAC
+		address of the slaves is not changed; instead, the MAC
+		address of the bond changes during a failover.
+
+		This policy is useful for devices that cannot ever
+		alter their MAC address, or for devices that refuse
+		incoming broadcasts with their own source MAC (which
+		interferes with the ARP monitor).
+
+		The down side of this policy is that every device on
+		the network must be updated via gratuitous ARP,
+		vs. just updating a switch or set of switches (which
+		often takes place for any traffic, not just ARP
+		traffic, if the switch snoops incoming traffic to
+		update its tables) for the traditional method.  If the
+		gratuitous ARP is lost, communication may be
+		disrupted.
+
+		When this policy is used in conjuction with the mii
+		monitor, devices which assert link up prior to being
+		able to actually transmit and receive are particularly
+		susecptible to loss of the gratuitous ARP, and an
+		appropriate updelay setting may be required.
+
+	follow or 2
+
+		The "follow" fail_over_mac policy causes the MAC
+		address of the bond to be selected normally (normally
+		the MAC address of the first slave added to the bond).
+		However, the second and subsequent slaves are not set
+		to this MAC address while they are in a backup role; a
+		slave is programmed with the bond's MAC address at
+		failover time (and the formerly active slave receives
+		the newly active slave's MAC address).
+
+		This policy is useful for multiport devices that
+		either become confused or incur a performance penalty
+		when multiple ports are programmed with the same MAC
+		address.
+
+
+	The default policy is none, unless the first slave cannot
+	change its MAC address, in which case the active policy is
+	selected by default.
+
+	This option may be modified via sysfs only when no slaves are
+	present in the bond.
+
+	This option was added in bonding version 3.2.0.  The "follow"
+	policy was added in bonding version 3.3.0.
 
 lacp_rate
 
@@ -338,7 +376,8 @@ max_bonds
 	Specifies the number of bonding devices to create for this
 	instance of the bonding driver.  E.g., if max_bonds is 3, and
 	the bonding driver is not already loaded, then bond0, bond1
-	and bond2 will be created.  The default value is 1.
+	and bond2 will be created.  The default value is 1.  Specifying
+	a value of 0 will load bonding, but will not create any devices.
 
 miimon
 
@@ -501,6 +540,17 @@ mode
 		swapped with the new curr_active_slave that was
 		chosen.
 
+num_grat_arp
+
+	Specifies the number of gratuitous ARPs to be issued after a
+	failover event.  One gratuitous ARP is issued immediately after
+	the failover, subsequent ARPs are sent at a rate of one per link
+	monitor interval (arp_interval or miimon, whichever is active).
+
+	The valid range is 0 - 255; the default value is 1.  This option
+	affects only the active-backup mode.  This option was added for
+	bonding version 3.3.0.
+
 primary
 
 	A string (eth0, eth2, etc) specifying which slave is the

trunk/Documentation/networking/dm9000.txt

@@ -0,0 +1,167 @@
+DM9000 Network driver
+=====================
+
+Copyright 2008 Simtec Electronics,
+	  Ben Dooks <ben@simtec.co.uk> <ben-linux@fluff.org>
+
+
+Introduction
+------------
+
+This file describes how to use the DM9000 platform-device based network driver
+that is contained in the files drivers/net/dm9000.c and drivers/net/dm9000.h.
+
+The driver supports three DM9000 variants, the DM9000E which is the first chip
+supported as well as the newer DM9000A and DM9000B devices. It is currently
+maintained and tested by Ben Dooks, who should be CC: to any patches for this
+driver.
+
+
+Defining the platform device
+----------------------------
+
+The minimum set of resources attached to the platform device are as follows:
+
+    1) The physical address of the address register
+    2) The physical address of the data register
+    3) The IRQ line the device's interrupt pin is connected to.
+
+These resources should be specified in that order, as the ordering of the
+two address regions is important (the driver expects these to be address
+and then data).
+
+An example from arch/arm/mach-s3c2410/mach-bast.c is:
+
+static struct resource bast_dm9k_resource[] = {
+	[0] = {
+		.start = S3C2410_CS5 + BAST_PA_DM9000,
+		.end   = S3C2410_CS5 + BAST_PA_DM9000 + 3,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = S3C2410_CS5 + BAST_PA_DM9000 + 0x40,
+		.end   = S3C2410_CS5 + BAST_PA_DM9000 + 0x40 + 0x3f,
+		.flags = IORESOURCE_MEM,
+	},
+	[2] = {
+		.start = IRQ_DM9000,
+		.end   = IRQ_DM9000,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	}
+};
+
+static struct platform_device bast_device_dm9k = {
+	.name		= "dm9000",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(bast_dm9k_resource),
+	.resource	= bast_dm9k_resource,
+};
+
+Note the setting of the IRQ trigger flag in bast_dm9k_resource[2].flags,
+as this will generate a warning if it is not present. The trigger from
+the flags field will be passed to request_irq() when registering the IRQ
+handler to ensure that the IRQ is setup correctly.
+
+This shows a typical platform device, without the optional configuration
+platform data supplied. The next example uses the same resources, but adds
+the optional platform data to pass extra configuration data:
+
+static struct dm9000_plat_data bast_dm9k_platdata = {
+	.flags		= DM9000_PLATF_16BITONLY,
+};
+
+static struct platform_device bast_device_dm9k = {
+	.name		= "dm9000",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(bast_dm9k_resource),
+	.resource	= bast_dm9k_resource,
+	.dev		= {
+		.platform_data = &bast_dm9k_platdata,
+	}
+};
+
+The platform data is defined in include/linux/dm9000.h and described below.
+
+
+Platform data
+-------------
+
+Extra platform data for the DM9000 can describe the IO bus width to the
+device, whether or not an external PHY is attached to the device and
+the availability of an external configuration EEPROM.
+
+The flags for the platform data .flags field are as follows:
+
+DM9000_PLATF_8BITONLY
+
+	The IO should be done with 8bit operations.
+
+DM9000_PLATF_16BITONLY
+
+	The IO should be done with 16bit operations.
+
+DM9000_PLATF_32BITONLY
+
+	The IO should be done with 32bit operations.
+
+DM9000_PLATF_EXT_PHY
+
+	The chip is connected to an external PHY.
+
+DM9000_PLATF_NO_EEPROM
+
+	This can be used to signify that the board does not have an
+	EEPROM, or that the EEPROM should be hidden from the user.
+
+DM9000_PLATF_SIMPLE_PHY
+
+	Switch to using the simpler PHY polling method which does not
+	try and read the MII PHY state regularly. This is only available
+	when using the internal PHY. See the section on link state polling
+	for more information.
+
+	The config symbol DM9000_FORCE_SIMPLE_PHY_POLL, Kconfig entry
+	"Force simple NSR based PHY polling" allows this flag to be
+	forced on at build time.
+
+
+PHY Link state polling
+----------------------
+
+The driver keeps track of the link state and informs the network core
+about link (carrier) availablilty. This is managed by several methods
+depending on the version of the chip and on which PHY is being used.
+
+For the internal PHY, the original (and currently default) method is
+to read the MII state, either when the status changes if we have the
+necessary interrupt support in the chip or every two seconds via a
+periodic timer.
+
+To reduce the overhead for the internal PHY, there is now the option
+of using the DM9000_FORCE_SIMPLE_PHY_POLL config, or DM9000_PLATF_SIMPLE_PHY
+platform data option to read the summary information without the
+expensive MII accesses. This method is faster, but does not print
+as much information.
+
+When using an external PHY, the driver currently has to poll the MII
+link status as there is no method for getting an interrupt on link change.
+
+
+DM9000A / DM9000B
+-----------------
+
+These chips are functionally similar to the DM9000E and are supported easily
+by the same driver. The features are:
+
+   1) Interrupt on internal PHY state change. This means that the periodic
+      polling of the PHY status may be disabled on these devices when using
+      the internal PHY.
+
+   2) TCP/UDP checksum offloading, which the driver does not currently support.
+
+
+ethtool
+-------
+
+The driver supports the ethtool interface for access to the driver
+state information, the PHY state and the EEPROM.

trunk/Documentation/networking/ip-sysctl.txt

@@ -551,8 +551,9 @@ icmp_echo_ignore_broadcasts - BOOLEAN
 icmp_ratelimit - INTEGER
 	Limit the maximal rates for sending ICMP packets whose type matches
 	icmp_ratemask (see below) to specific targets.
-	0 to disable any limiting, otherwise the maximal rate in jiffies(1)
-	Default: 100
+	0 to disable any limiting,
+	otherwise the minimal space between responses in milliseconds.
+	Default: 1000
 
 icmp_ratemask - INTEGER
 	Mask made of ICMP types for which rates are being limited.
@@ -1023,11 +1024,23 @@ max_addresses - INTEGER
 	autoconfigured addresses.
 	Default: 16
 
+disable_ipv6 - BOOLEAN
+	Disable IPv6 operation.
+	Default: FALSE (enable IPv6 operation)
+
+accept_dad - INTEGER
+	Whether to accept DAD (Duplicate Address Detection).
+	0: Disable DAD
+	1: Enable DAD (default)
+	2: Enable DAD, and disable IPv6 operation if MAC-based duplicate
+	   link-local address has been found.
+
 icmp/*:
 ratelimit - INTEGER
 	Limit the maximal rates for sending ICMPv6 packets.
-	0 to disable any limiting, otherwise the maximal rate in jiffies(1)
-	Default: 100
+	0 to disable any limiting,
+	otherwise the minimal space between responses in milliseconds.
+	Default: 1000
 
 
 IPv6 Update by: