Skip to content

Commit

Permalink
V4L/DVB (12182): cx18: Add DVB-T support for Yuan MPC-718 cards with …
Browse files Browse the repository at this point in the history 
…an MT352 or ZL10353

Add DVB-T support for Yuan MPC-718 cards with an MT352 or ZL10353 demodulator.

There are apparently some units with a DiBcom demodulator which could be
supported by one of the dib7000 modules - but this is not implemented in the
cx18 driver (yet).

Due to lack of porgramming details for the MT352 and the mt352 module requiring
a "demod_init" function, a "firmware" must be obtained and loaded to get
DVB-T working for Yuan MPC-718 cards with an MT352.

Tested-by: Steve Firth <firth650@btinternet.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
  • Loading branch information
Andy Walls authored and Mauro Carvalho Chehab committed Jul 5, 2009
1 parent 9f38a92 commit ff861fb
Show file tree
Hide file tree
Showing 2 changed files with 162 additions and 2 deletions.
4 changes: 2 additions & 2 deletions drivers/media/video/cx18/cx18-cards.c
View file
Original file line number Diff line number Diff line change
Expand Up @@ -204,8 +204,8 @@ static const struct cx18_card cx18_card_mpc718 = {
.v4l2_capabilities = CX18_CAP_ENCODER,
.hw_audio_ctrl = CX18_HW_418_AV,
.hw_muxer = CX18_HW_GPIO_MUX,
.hw_all = CX18_HW_418_AV | CX18_HW_TUNER | CX18_HW_GPIO_MUX |
CX18_HW_GPIO_RESET_CTRL,
.hw_all = CX18_HW_418_AV | CX18_HW_TUNER |
CX18_HW_GPIO_MUX | CX18_HW_DVB | CX18_HW_GPIO_RESET_CTRL,
.video_inputs = {
{ CX18_CARD_INPUT_VID_TUNER, 0, CX18_AV_COMPOSITE2 },
{ CX18_CARD_INPUT_SVIDEO1, 1,
Expand Down
160 changes: 160 additions & 0 deletions drivers/media/video/cx18/cx18-dvb.c
View file
Original file line number Diff line number Diff line change
Expand Up @@ -30,6 +30,10 @@
#include "s5h1409.h"
#include "mxl5005s.h"
#include "zl10353.h"

#include <linux/firmware.h>
#include "mt352.h"
#include "mt352_priv.h"
#include "tuner-xc2028.h"

DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr);
Expand All @@ -38,6 +42,11 @@ DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr);
#define CX18_CLOCK_ENABLE2 0xc71024
#define CX18_DMUX_CLK_MASK 0x0080

/*
* CX18_CARD_HVR_1600_ESMT
* CX18_CARD_HVR_1600_SAMSUNG
*/

static struct mxl5005s_config hauppauge_hvr1600_tuner = {
.i2c_address = 0xC6 >> 1,
.if_freq = IF_FREQ_5380000HZ,
Expand Down Expand Up @@ -65,6 +74,9 @@ static struct s5h1409_config hauppauge_hvr1600_config = {
.mpeg_timing = S5H1409_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK
};

/*
* CX18_CARD_LEADTEK_DVR3100H
*/
/* Information/confirmation of proper config values provided by Terry Wu */
static struct zl10353_config leadtek_dvr3100h_demod = {
.demod_address = 0x1e >> 1, /* Datasheet suggested straps */
Expand All @@ -74,6 +86,121 @@ static struct zl10353_config leadtek_dvr3100h_demod = {
.disable_i2c_gate_ctrl = 1, /* Disable the I2C gate */
};

/*
* CX18_CARD_YUAN_MPC718
*/
/*
* Due to
*
* 1. an absence of information on how to prgram the MT352
* 2. the Linux mt352 module pushing MT352 initialzation off onto us here
*
* We have to use an init sequence that *you* must extract from the Windows
* driver (yuanrap.sys) and which we load as a firmware.
*
* If someone can provide me with a Zarlink MT352 (Intel CE6352?) Design Manual
* with chip programming details, then I can remove this annoyance.
*/
static int yuan_mpc718_mt352_reqfw(struct cx18_stream *stream,
const struct firmware **fw)
{
struct cx18 *cx = stream->cx;
const char *fn = "dvb-cx18-mpc718-mt352.fw";
int ret;

ret = request_firmware(fw, fn, &cx->pci_dev->dev);
if (ret)
CX18_ERR("Unable to open firmware file %s\n", fn);
else {
size_t sz = (*fw)->size;
if (sz < 2 || sz > 64 || (sz % 2) != 0) {
CX18_ERR("Firmware %s has a bad size: %lu bytes\n",
fn, (unsigned long) sz);
ret = -EILSEQ;
release_firmware(*fw);
*fw = NULL;
}
}

if (ret) {
CX18_ERR("The MPC718 board variant with the MT352 DVB-T"
"demodualtor will not work without it\n");
CX18_ERR("Run 'linux/Documentation/dvb/get_dvb_firmware "
"mpc718' if you need the firmware\n");
}
return ret;
}

static int yuan_mpc718_mt352_init(struct dvb_frontend *fe)
{
struct cx18_dvb *dvb = container_of(fe->dvb,
struct cx18_dvb, dvb_adapter);
struct cx18_stream *stream = container_of(dvb, struct cx18_stream, dvb);
const struct firmware *fw = NULL;
int ret;
int i;
u8 buf[3];

ret = yuan_mpc718_mt352_reqfw(stream, &fw);
if (ret)
return ret;

/* Loop through all the register-value pairs in the firmware file */
for (i = 0; i < fw->size; i += 2) {
buf[0] = fw->data[i];
/* Intercept a few registers we want to set ourselves */
switch (buf[0]) {
case TRL_NOMINAL_RATE_0:
/* Set our custom OFDM bandwidth in the case below */
break;
case TRL_NOMINAL_RATE_1:
/* 6 MHz: 64/7 * 6/8 / 20.48 * 2^16 = 0x55b6.db6 */
/* 7 MHz: 64/7 * 7/8 / 20.48 * 2^16 = 0x6400 */
/* 8 MHz: 64/7 * 8/8 / 20.48 * 2^16 = 0x7249.249 */
buf[1] = 0x72;
buf[2] = 0x49;
mt352_write(fe, buf, 3);
break;
case INPUT_FREQ_0:
/* Set our custom IF in the case below */
break;
case INPUT_FREQ_1:
/* 4.56 MHz IF: (20.48 - 4.56)/20.48 * 2^14 = 0x31c0 */
buf[1] = 0x31;
buf[2] = 0xc0;
mt352_write(fe, buf, 3);
break;
default:
/* Pass through the register-value pair from the fw */
buf[1] = fw->data[i+1];
mt352_write(fe, buf, 2);
break;
}
}

buf[0] = (u8) TUNER_GO;
buf[1] = 0x01; /* Go */
mt352_write(fe, buf, 2);
release_firmware(fw);
return 0;
}

static struct mt352_config yuan_mpc718_mt352_demod = {
.demod_address = 0x1e >> 1,
.adc_clock = 20480, /* 20.480 MHz */
.if2 = 4560, /* 4.560 MHz */
.no_tuner = 1, /* XC3028 is not behind the gate */
.demod_init = yuan_mpc718_mt352_init,
};

static struct zl10353_config yuan_mpc718_zl10353_demod = {
.demod_address = 0x1e >> 1, /* Datasheet suggested straps */
.if2 = 45600, /* 4.560 MHz IF from the XC3028 */
.parallel_ts = 1, /* Not a serial TS */
.no_tuner = 1, /* XC3028 is not behind the gate */
.disable_i2c_gate_ctrl = 1, /* Disable the I2C gate */
};

static int dvb_register(struct cx18_stream *stream);

/* Kernel DVB framework calls this when the feed needs to start.
Expand Down Expand Up @@ -113,6 +240,7 @@ static int cx18_dvb_start_feed(struct dvb_demux_feed *feed)
break;

case CX18_CARD_LEADTEK_DVR3100H:
case CX18_CARD_YUAN_MPC718:
default:
/* Assumption - Parallel transport - Signalling
* undefined or default.
Expand Down Expand Up @@ -326,6 +454,38 @@ static int dvb_register(struct cx18_stream *stream)
fe->ops.tuner_ops.set_config(fe, &ctrl);
}
break;
case CX18_CARD_YUAN_MPC718:
/*
* TODO
* Apparently, these cards also could instead have a
* DiBcom demod supported by one of the db7000 drivers
*/
dvb->fe = dvb_attach(mt352_attach,
&yuan_mpc718_mt352_demod,
&cx->i2c_adap[1]);
if (dvb->fe == NULL)
dvb->fe = dvb_attach(zl10353_attach,
&yuan_mpc718_zl10353_demod,
&cx->i2c_adap[1]);
if (dvb->fe != NULL) {
struct dvb_frontend *fe;
struct xc2028_config cfg = {
.i2c_adap = &cx->i2c_adap[1],
.i2c_addr = 0xc2 >> 1,
.ctrl = NULL,
};
static struct xc2028_ctrl ctrl = {
.fname = XC2028_DEFAULT_FIRMWARE,
.max_len = 64,
.demod = XC3028_FE_ZARLINK456,
.type = XC2028_AUTO,
};

fe = dvb_attach(xc2028_attach, dvb->fe, &cfg);
if (fe != NULL && fe->ops.tuner_ops.set_config != NULL)
fe->ops.tuner_ops.set_config(fe, &ctrl);
}
break;
default:
/* No Digital Tv Support */
break;
Expand Down

0 comments on commit ff861fb

Please sign in to comment.