Merge branch 'gmac-next'

Roger Chen says: ==================== support GMAC driver for RK3288 Roger Chen (6): patch1: add driver for Rockchip RK3288 SoCs integrated GMAC patch2: define clock ID used for GMAC patch3: modify CRU config for Rockchip RK3288 SoCs integrated GMAC patch4: dts: rockchip: add gmac info for rk3288 patch5: dts: rockchip: enable gmac on RK3288 evb board patch6: add document for Rockchip RK3288 GMAC Tested on rk3288 evb board: Execute the following command to enable ethernet, set local IP and ping a remote host. busybox ifconfig eth0 up busybox ifconfig eth0 192.168.1.111 ping 192.168.1.1 ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
mariux64 · Jan 1, 2015 · 01aa299 · 01aa299
2 parents 9aacfb2 + 53a8393
commit 01aa299
Show file tree

Hide file tree

Showing 10 changed files with 633 additions and 8 deletions.
diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
@@ -0,0 +1,67 @@
+Rockchip SoC RK3288 10/100/1000 Ethernet driver(GMAC)
+
+The device node has following properties.
+
+Required properties:
+ - compatible: Can be "rockchip,rk3288-gmac".
+ - reg: addresses and length of the register sets for the device.
+ - interrupts: Should contain the GMAC interrupts.
+ - interrupt-names: Should contain the interrupt names "macirq".
+ - rockchip,grf: phandle to the syscon grf used to control speed and mode.
+ - clocks: <&cru SCLK_MAC>: clock selector for main clock, from PLL or PHY.
+	   <&cru SCLK_MAC_PLL>: PLL clock for SCLK_MAC
+	   <&cru SCLK_MAC_RX>: clock gate for RX
+	   <&cru SCLK_MAC_TX>: clock gate for TX
+	   <&cru SCLK_MACREF>: clock gate for RMII referce clock
+	   <&cru SCLK_MACREF_OUT> clock gate for RMII reference clock output
+	   <&cru ACLK_GMAC>: AXI clock gate for GMAC
+	   <&cru PCLK_GMAC>: APB clock gate for GMAC
+ - clock-names: One name for each entry in the clocks property.
+ - phy-mode: See ethernet.txt file in the same directory.
+ - pinctrl-names: Names corresponding to the numbered pinctrl states.
+ - pinctrl-0: pin-control mode. can be <&rgmii_pins> or <&rmii_pins>.
+ - clock_in_out: For RGMII, it must be "input", means main clock(125MHz)
+   is not sourced from SoC's PLL, but input from PHY; For RMII, "input" means
+   PHY provides the reference clock(50MHz), "output" means GMAC provides the
+   reference clock.
+ - snps,reset-gpio       gpio number for phy reset.
+ - snps,reset-active-low boolean flag to indicate if phy reset is active low.
+ - assigned-clocks: main clock, should be <&cru SCLK_MAC>;
+ - assigned-clock-parents = parent of main clock.
+   can be <&ext_gmac> or <&cru SCLK_MAC_PLL>.
+
+Optional properties:
+ - tx_delay: Delay value for TXD timing. Range value is 0~0x7F, 0x30 as default.
+ - rx_delay: Delay value for RXD timing. Range value is 0~0x7F, 0x10 as default.
+
+Example:
+
+gmac: ethernet@ff290000 {
+	compatible = "rockchip,rk3288-gmac";
+	reg = <0xff290000 0x10000>;
+	interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+	interrupt-names = "macirq";
+	rockchip,grf = <&grf>;
+	clocks = <&cru SCLK_MAC>,
+		<&cru SCLK_MAC_RX>, <&cru SCLK_MAC_TX>,
+		<&cru SCLK_MACREF>, <&cru SCLK_MACREF_OUT>,
+		<&cru ACLK_GMAC>, <&cru PCLK_GMAC>;
+	clock-names = "stmmaceth",
+		"mac_clk_rx", "mac_clk_tx",
+		"clk_mac_ref", "clk_mac_refout",
+		"aclk_mac", "pclk_mac";
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins /*&rmii_pins*/>;
+
+	clock_in_out = "input";
+	snps,reset-gpio = <&gpio4 7 0>;
+	snps,reset-active-low;
+
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+
+	status = "ok";
+};
diff --git a/arch/arm/boot/dts/rk3288-evb-rk808.dts b/arch/arm/boot/dts/rk3288-evb-rk808.dts
@@ -15,6 +15,13 @@
 
 / {
 	compatible = "rockchip,rk3288-evb-rk808", "rockchip,rk3288";
+
+	ext_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "ext_gmac";
+		#clock-cells = <0>;
+	};
 };
 
 &cpu0 {
@@ -152,3 +159,19 @@
 		};
 	};
 };
+
+&gmac {
+	phy_regulator = "vcc_phy";
+	phy-mode = "rgmii";
+	clock_in_out = "input";
+	snps,reset-gpio = <&gpio4 7 0>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 1000000>;
+	assigned-clocks = <&cru SCLK_MAC>;
+	assigned-clock-parents = <&ext_gmac>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	status = "ok";
+};
diff --git a/arch/arm/boot/dts/rk3288-evb.dtsi b/arch/arm/boot/dts/rk3288-evb.dtsi
@@ -90,6 +90,17 @@
 		regulator-always-on;
 		regulator-boot-on;
 	};
+
+	vcc_phy: vcc-phy-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&eth_phy_pwr>;
+		regulator-name = "vcc_phy";
+		regulator-always-on;
+		regulator-boot-on;
+	};
 };
 
 &emmc {
@@ -178,6 +189,12 @@
 			rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
+
+	eth_phy {
+		eth_phy_pwr: eth-phy-pwr {
+			rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
 };
 
 &usb_host0_ehci {

diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi
@@ -380,6 +380,22 @@
 		status = "disabled";
 	};
 
+	gmac: ethernet@ff290000 {
+		compatible = "rockchip,rk3288-gmac";
+		reg = <0xff290000 0x10000>;
+		interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "macirq";
+		rockchip,grf = <&grf>;
+		clocks = <&cru SCLK_MAC>,
+			<&cru SCLK_MAC_RX>, <&cru SCLK_MAC_TX>,
+			<&cru SCLK_MACREF>, <&cru SCLK_MACREF_OUT>,
+			<&cru ACLK_GMAC>, <&cru PCLK_GMAC>;
+		clock-names = "stmmaceth",
+			"mac_clk_rx", "mac_clk_tx",
+			"clk_mac_ref", "clk_mac_refout",
+			"aclk_mac", "pclk_mac";
+	};
+
 	usb_host0_ehci: usb@ff500000 {
 		compatible = "generic-ehci";
 		reg = <0xff500000 0x100>;
@@ -725,6 +741,11 @@
 			bias-disable;
 		};
 
+		pcfg_pull_none_12ma: pcfg-pull-none-12ma {
+			bias-disable;
+			drive-strength = <12>;
+		};
+
 		i2c0 {
 			i2c0_xfer: i2c0-xfer {
 				rockchip,pins = <0 15 RK_FUNC_1 &pcfg_pull_none>,
@@ -1068,5 +1089,38 @@
 				rockchip,pins = <7 23 3 &pcfg_pull_none>;
 			};
 		};
+
+		gmac {
+			rgmii_pins: rgmii-pins {
+				rockchip,pins = <3 30 3 &pcfg_pull_none>,
+						<3 31 3 &pcfg_pull_none>,
+						<3 26 3 &pcfg_pull_none>,
+						<3 27 3 &pcfg_pull_none>,
+						<3 28 3 &pcfg_pull_none_12ma>,
+						<3 29 3 &pcfg_pull_none_12ma>,
+						<3 24 3 &pcfg_pull_none_12ma>,
+						<3 25 3 &pcfg_pull_none_12ma>,
+						<4 0 3 &pcfg_pull_none>,
+						<4 5 3 &pcfg_pull_none>,
+						<4 6 3 &pcfg_pull_none>,
+						<4 9 3 &pcfg_pull_none_12ma>,
+						<4 4 3 &pcfg_pull_none_12ma>,
+						<4 1 3 &pcfg_pull_none>,
+						<4 3 3 &pcfg_pull_none>;
+			};
+
+			rmii_pins: rmii-pins {
+				rockchip,pins = <3 30 3 &pcfg_pull_none>,
+						<3 31 3 &pcfg_pull_none>,
+						<3 28 3 &pcfg_pull_none>,
+						<3 29 3 &pcfg_pull_none>,
+						<4 0 3 &pcfg_pull_none>,
+						<4 5 3 &pcfg_pull_none>,
+						<4 4 3 &pcfg_pull_none>,
+						<4 1 3 &pcfg_pull_none>,
+						<4 2 3 &pcfg_pull_none>,
+						<4 3 3 &pcfg_pull_none>;
+			};
+		};
 	};
 };
diff --git a/drivers/clk/rockchip/clk-rk3288.c b/drivers/clk/rockchip/clk-rk3288.c
@@ -190,7 +190,7 @@ PNAME(mux_uart2_p)	= { "uart2_src", "uart2_frac", "xin24m" };
 PNAME(mux_uart3_p)	= { "uart3_src", "uart3_frac", "xin24m" };
 PNAME(mux_uart4_p)	= { "uart4_src", "uart4_frac", "xin24m" };
 PNAME(mux_cif_out_p)	= { "cif_src", "xin24m" };
-PNAME(mux_macref_p)	= { "mac_src", "ext_gmac" };
+PNAME(mux_mac_p)	= { "mac_pll_src", "ext_gmac" };
 PNAME(mux_hsadcout_p)	= { "hsadc_src", "ext_hsadc" };
 PNAME(mux_edp_24m_p)	= { "ext_edp_24m", "xin24m" };
 PNAME(mux_tspout_p)	= { "cpll", "gpll", "npll", "xin27m" };
@@ -575,18 +575,18 @@ static struct rockchip_clk_branch rk3288_clk_branches[] __initdata = {
 	MUX(SCLK_UART4, "sclk_uart4", mux_uart4_p, 0,
 			RK3288_CLKSEL_CON(3), 8, 2, MFLAGS),
 
-	COMPOSITE(0, "mac_src", mux_pll_src_npll_cpll_gpll_p, 0,
+	COMPOSITE(0, "mac_pll_src", mux_pll_src_npll_cpll_gpll_p, 0,
 			RK3288_CLKSEL_CON(21), 0, 2, MFLAGS, 8, 5, DFLAGS,
 			RK3288_CLKGATE_CON(2), 5, GFLAGS),
-	MUX(0, "macref", mux_macref_p, 0,
+	MUX(SCLK_MAC, "mac_clk", mux_mac_p, 0,
 			RK3288_CLKSEL_CON(21), 4, 1, MFLAGS),
-	GATE(0, "sclk_macref_out", "macref", 0,
+	GATE(SCLK_MACREF_OUT, "sclk_macref_out", "mac_clk", 0,
 			RK3288_CLKGATE_CON(5), 3, GFLAGS),
-	GATE(SCLK_MACREF, "sclk_macref", "macref", 0,
+	GATE(SCLK_MACREF, "sclk_macref", "mac_clk", 0,
 			RK3288_CLKGATE_CON(5), 2, GFLAGS),
-	GATE(SCLK_MAC_RX, "sclk_mac_rx", "macref", 0,
+	GATE(SCLK_MAC_RX, "sclk_mac_rx", "mac_clk", 0,
 			RK3288_CLKGATE_CON(5), 0, GFLAGS),
-	GATE(SCLK_MAC_TX, "sclk_mac_tx", "macref", 0,
+	GATE(SCLK_MAC_TX, "sclk_mac_tx", "mac_clk", 0,
 			RK3288_CLKGATE_CON(5), 1, GFLAGS),
 
 	COMPOSITE(0, "hsadc_src", mux_pll_src_cpll_gpll_p, 0,

diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
@@ -6,7 +6,7 @@ stmmac-objs:= stmmac_main.o stmmac_ethtool.o stmmac_mdio.o ring_mode.o	\
 
 obj-$(CONFIG_STMMAC_PLATFORM) += stmmac-platform.o
 stmmac-platform-objs:= stmmac_platform.o dwmac-meson.o dwmac-sunxi.o	\
-		       dwmac-sti.o dwmac-socfpga.o
+		       dwmac-sti.o dwmac-socfpga.o dwmac-rk.o
 
 obj-$(CONFIG_STMMAC_PCI) += stmmac-pci.o
 stmmac-pci-objs:= stmmac_pci.o