mtd: nand: omap: Copy platform data parameters to omap_nand_info data

Copy all the platform data parameters to the driver's local data
structure 'omap_nand_info' and use it in the entire driver. This will
make it easer for device tree migration.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>

drivers/mtd/nand/omap2.c

@@ -152,13 +152,17 @@ static struct nand_hw_control omap_gpmc_controller = {
 };
 
 struct omap_nand_info {
-	struct omap_nand_platform_data	*pdata;
 	struct nand_chip		nand;
 	struct platform_device		*pdev;
 
 	int				gpmc_cs;
-	unsigned long			phys_base;
+	bool				dev_ready;
+	enum nand_io			xfer_type;
+	int				devsize;
 	enum omap_ecc			ecc_opt;
+	struct device_node		*elm_of_node;
+
+	unsigned long			phys_base;
 	struct completion		comp;
 	struct dma_chan			*dma;
 	int				gpmc_irq_fifo;
@@ -1631,7 +1635,7 @@ static bool omap2_nand_ecc_check(struct omap_nand_info *info,
 			"CONFIG_MTD_NAND_OMAP_BCH not enabled\n");
 		return false;
 	}
-	if (ecc_needs_elm && !is_elm_present(info, pdata->elm_of_node)) {
+	if (ecc_needs_elm && !is_elm_present(info, info->elm_of_node)) {
 		dev_err(&info->pdev->dev, "ELM not available\n");
 		return false;
 	}
@@ -1675,6 +1679,11 @@ static int omap_nand_probe(struct platform_device *pdev)
 	info->gpmc_cs		= pdata->cs;
 	info->of_node		= pdata->of_node;
 	info->ecc_opt		= pdata->ecc_opt;
+	info->dev_ready	= pdata->dev_ready;
+	info->xfer_type = pdata->xfer_type;
+	info->devsize = pdata->devsize;
+	info->elm_of_node = pdata->elm_of_node;
+
 	nand_chip		= &info->nand;
 	mtd			= nand_to_mtd(nand_chip);
 	mtd->dev.parent		= &pdev->dev;
@@ -1700,7 +1709,7 @@ static int omap_nand_probe(struct platform_device *pdev)
 	 * chip delay which is slightly more than tR (AC Timing) of the NAND
 	 * device and read status register until you get a failure or success
 	 */
-	if (pdata->dev_ready) {
+	if (info->dev_ready) {
 		nand_chip->dev_ready = omap_dev_ready;
 		nand_chip->chip_delay = 0;
 	} else {
@@ -1714,15 +1723,16 @@ static int omap_nand_probe(struct platform_device *pdev)
 		nand_chip->options |= NAND_SKIP_BBTSCAN;
 
 	/* scan NAND device connected to chip controller */
-	nand_chip->options |= pdata->devsize & NAND_BUSWIDTH_16;
+	nand_chip->options |= info->devsize & NAND_BUSWIDTH_16;
 	if (nand_scan_ident(mtd, 1, NULL)) {
-		dev_err(&info->pdev->dev, "scan failed, may be bus-width mismatch\n");
+		dev_err(&info->pdev->dev,
+			"scan failed, may be bus-width mismatch\n");
 		err = -ENXIO;
 		goto return_error;
 	}
 
 	/* re-populate low-level callbacks based on xfer modes */
-	switch (pdata->xfer_type) {
+	switch (info->xfer_type) {
 	case NAND_OMAP_PREFETCH_POLLED:
 		nand_chip->read_buf   = omap_read_buf_pref;
 		nand_chip->write_buf  = omap_write_buf_pref;
@@ -1802,7 +1812,7 @@ static int omap_nand_probe(struct platform_device *pdev)
 
 	default:
 		dev_err(&pdev->dev,
-			"xfer_type(%d) not supported!\n", pdata->xfer_type);
+			"xfer_type(%d) not supported!\n", info->xfer_type);
 		err = -EINVAL;
 		goto return_error;
 	}