net: stmmac: xgmac: Add C45 PHY support in the MDIO callbacks

Add the support for C45 PHYs in the MDIO callbacks for XGMAC. This was
tested using Synopsys DesignWare XPCS.

v2:
- Pull out the readl_poll_timeout() calls into common code (Andrew)

Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c

@@ -41,28 +41,40 @@
 #define MII_XGMAC_BUSY			BIT(22)
 #define MII_XGMAC_MAX_C22ADDR		3
 #define MII_XGMAC_C22P_MASK		GENMASK(MII_XGMAC_MAX_C22ADDR, 0)
+#define MII_XGMAC_PA_SHIFT		16
+#define MII_XGMAC_DA_SHIFT		21
+
+static int stmmac_xgmac2_c45_format(struct stmmac_priv *priv, int phyaddr,
+				    int phyreg, u32 *hw_addr)
+{
+	u32 tmp;
+
+	/* Set port as Clause 45 */
+	tmp = readl(priv->ioaddr + XGMAC_MDIO_C22P);
+	tmp &= ~BIT(phyaddr);
+	writel(tmp, priv->ioaddr + XGMAC_MDIO_C22P);
+
+	*hw_addr = (phyaddr << MII_XGMAC_PA_SHIFT) | (phyreg & 0xffff);
+	*hw_addr |= (phyreg >> MII_DEVADDR_C45_SHIFT) << MII_XGMAC_DA_SHIFT;
+	return 0;
+}
 
 static int stmmac_xgmac2_c22_format(struct stmmac_priv *priv, int phyaddr,
 				    int phyreg, u32 *hw_addr)
 {
-	unsigned int mii_data = priv->hw->mii.data;
 	u32 tmp;
 
 	/* HW does not support C22 addr >= 4 */
 	if (phyaddr > MII_XGMAC_MAX_C22ADDR)
 		return -ENODEV;
-	/* Wait until any existing MII operation is complete */
-	if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
-			       !(tmp & MII_XGMAC_BUSY), 100, 10000))
-		return -EBUSY;
 
 	/* Set port as Clause 22 */
 	tmp = readl(priv->ioaddr + XGMAC_MDIO_C22P);
 	tmp &= ~MII_XGMAC_C22P_MASK;
 	tmp |= BIT(phyaddr);
 	writel(tmp, priv->ioaddr + XGMAC_MDIO_C22P);
 
-	*hw_addr = (phyaddr << 16) | (phyreg & 0x1f);
+	*hw_addr = (phyaddr << MII_XGMAC_PA_SHIFT) | (phyreg & 0x1f);
 	return 0;
 }
 
@@ -75,17 +87,28 @@ static int stmmac_xgmac2_mdio_read(struct mii_bus *bus, int phyaddr, int phyreg)
 	u32 tmp, addr, value = MII_XGMAC_BUSY;
 	int ret;
 
+	/* Wait until any existing MII operation is complete */
+	if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
+			       !(tmp & MII_XGMAC_BUSY), 100, 10000))
+		return -EBUSY;
+
 	if (phyreg & MII_ADDR_C45) {
-		return -EOPNOTSUPP;
+		phyreg &= ~MII_ADDR_C45;
+
+		ret = stmmac_xgmac2_c45_format(priv, phyaddr, phyreg, &addr);
+		if (ret)
+			return ret;
 	} else {
 		ret = stmmac_xgmac2_c22_format(priv, phyaddr, phyreg, &addr);
 		if (ret)
 			return ret;
+
+		value |= MII_XGMAC_SADDR;
 	}
 
 	value |= (priv->clk_csr << priv->hw->mii.clk_csr_shift)
 		& priv->hw->mii.clk_csr_mask;
-	value |= MII_XGMAC_SADDR | MII_XGMAC_READ;
+	value |= MII_XGMAC_READ;
 
 	/* Wait until any existing MII operation is complete */
 	if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
@@ -115,17 +138,28 @@ static int stmmac_xgmac2_mdio_write(struct mii_bus *bus, int phyaddr,
 	u32 addr, tmp, value = MII_XGMAC_BUSY;
 	int ret;
 
+	/* Wait until any existing MII operation is complete */
+	if (readl_poll_timeout(priv->ioaddr + mii_data, tmp,
+			       !(tmp & MII_XGMAC_BUSY), 100, 10000))
+		return -EBUSY;
+
 	if (phyreg & MII_ADDR_C45) {
-		return -EOPNOTSUPP;
+		phyreg &= ~MII_ADDR_C45;
+
+		ret = stmmac_xgmac2_c45_format(priv, phyaddr, phyreg, &addr);
+		if (ret)
+			return ret;
 	} else {
 		ret = stmmac_xgmac2_c22_format(priv, phyaddr, phyreg, &addr);
 		if (ret)
 			return ret;
+
+		value |= MII_XGMAC_SADDR;
 	}
 
 	value |= (priv->clk_csr << priv->hw->mii.clk_csr_shift)
 		& priv->hw->mii.clk_csr_mask;
-	value |= phydata | MII_XGMAC_SADDR;
+	value |= phydata;
 	value |= MII_XGMAC_WRITE;
 
 	/* Wait until any existing MII operation is complete */
@@ -363,6 +397,10 @@ int stmmac_mdio_register(struct net_device *ndev)
 		goto bus_register_fail;
 	}
 
+	/* Looks like we need a dummy read for XGMAC only and C45 PHYs */
+	if (priv->plat->has_xgmac)
+		stmmac_xgmac2_mdio_read(new_bus, 0, MII_ADDR_C45);
+
 	if (priv->plat->phy_node || mdio_node)
 		goto bus_register_done;