Merge tag 'drm-intel-fixes-2013-07-22' of git://people.freedesktop.or…

…g/~danvet/drm-intel into drm-fixes

- fixup panel fitter readout for gen2/3 (just quitens dmesg noise)
- fix pft computations for non-autoscaled resolutions (i.e. letter/pillar
  boxing on gen2/3)
- preserve the DDI A/E lane sharing bit (Stéphane Marchesin)
- fix the "rc6 fails to work after resume" regression, big thanks to
  Konstantin Khlebnikov for the patch and debug insight about what
  actually might be going on here
- fix Oops in is_crtc_connector_off (Chris)
- sanitize shared dpll state - our new paranoid state checker tripped up
  over dirt left behind by the BIOS
- correctly restore fences, fixes the "my screen is all messed up after
  resume" regression introduced in the final 3.10 pull request
- quirk backlights harder, this time for Dell XPS13 machines to fix a
  regression (patch from Kamal Mostafa)
- 90% fix for some haswell hangs when accessing registers concurrently,
  the 100% solution is simply too invasive for -fixes and what we have
  here seems to be good enough (Chris)

* tag 'drm-intel-fixes-2013-07-22' of git://people.freedesktop.org/~danvet/drm-intel:
  drm/i915: fix up gt init sequence fallout
  drm/i915: Serialize almost all register access
  drm/i915: quirk no PCH_PWM_ENABLE for Dell XPS13 backlight
  drm/i915: correctly restore fences with objects attached
  drm/i915: Fix dereferencing invalid connectors in is_crtc_connector_off()
  drm/i915: Sanitize shared dpll state
  drm/i915: fix long-standing SNB regression in power consumption after resume v2
  drm/i915: Preserve the DDI_A_4_LANES bit from the bios
  drm/i915: fix pfit regression for non-autoscaled resolutions
  drm/i915: fix up readout of the lvds dither bit on gen2/3

drivers/gpu/drm/i915/i915_dma.c

@@ -1495,6 +1495,14 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 	dev_priv->dev = dev;
 	dev_priv->info = info;
 
+	spin_lock_init(&dev_priv->irq_lock);
+	spin_lock_init(&dev_priv->gpu_error.lock);
+	spin_lock_init(&dev_priv->rps.lock);
+	spin_lock_init(&dev_priv->backlight.lock);
+	mutex_init(&dev_priv->dpio_lock);
+	mutex_init(&dev_priv->rps.hw_lock);
+	mutex_init(&dev_priv->modeset_restore_lock);
+
 	i915_dump_device_info(dev_priv);
 
 	if (i915_get_bridge_dev(dev)) {
@@ -1585,6 +1593,7 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 	intel_detect_pch(dev);
 
 	intel_irq_init(dev);
+	intel_gt_sanitize(dev);
 	intel_gt_init(dev);
 
 	/* Try to make sure MCHBAR is enabled before poking at it */
@@ -1610,15 +1619,6 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 	if (!IS_I945G(dev) && !IS_I945GM(dev))
 		pci_enable_msi(dev->pdev);
 
-	spin_lock_init(&dev_priv->irq_lock);
-	spin_lock_init(&dev_priv->gpu_error.lock);
-	spin_lock_init(&dev_priv->rps.lock);
-	spin_lock_init(&dev_priv->backlight.lock);
-	mutex_init(&dev_priv->dpio_lock);
-
-	mutex_init(&dev_priv->rps.hw_lock);
-	mutex_init(&dev_priv->modeset_restore_lock);
-
 	dev_priv->num_plane = 1;
 	if (IS_VALLEYVIEW(dev))
 		dev_priv->num_plane = 2;

drivers/gpu/drm/i915/i915_drv.c

@@ -706,7 +706,7 @@ static int i915_drm_thaw(struct drm_device *dev)
 {
 	int error = 0;
 
-	intel_gt_reset(dev);
+	intel_gt_sanitize(dev);
 
 	if (drm_core_check_feature(dev, DRIVER_MODESET)) {
 		mutex_lock(&dev->struct_mutex);
@@ -732,7 +732,7 @@ int i915_resume(struct drm_device *dev)
 
 	pci_set_master(dev->pdev);
 
-	intel_gt_reset(dev);
+	intel_gt_sanitize(dev);
 
 	/*
 	 * Platforms with opregion should have sane BIOS, older ones (gen3 and
@@ -1253,21 +1253,21 @@ hsw_unclaimed_reg_check(struct drm_i915_private *dev_priv, u32 reg)
 
 #define __i915_read(x, y) \
 u##x i915_read##x(struct drm_i915_private *dev_priv, u32 reg) { \
+	unsigned long irqflags; \
 	u##x val = 0; \
+	spin_lock_irqsave(&dev_priv->gt_lock, irqflags); \
 	if (IS_GEN5(dev_priv->dev)) \
 		ilk_dummy_write(dev_priv); \
 	if (NEEDS_FORCE_WAKE((dev_priv), (reg))) { \
-		unsigned long irqflags; \
-		spin_lock_irqsave(&dev_priv->gt_lock, irqflags); \
 		if (dev_priv->forcewake_count == 0) \
 			dev_priv->gt.force_wake_get(dev_priv); \
 		val = read##y(dev_priv->regs + reg); \
 		if (dev_priv->forcewake_count == 0) \
 			dev_priv->gt.force_wake_put(dev_priv); \
-		spin_unlock_irqrestore(&dev_priv->gt_lock, irqflags); \
 	} else { \
 		val = read##y(dev_priv->regs + reg); \
 	} \
+	spin_unlock_irqrestore(&dev_priv->gt_lock, irqflags); \
 	trace_i915_reg_rw(false, reg, val, sizeof(val)); \
 	return val; \
 }
@@ -1280,8 +1280,10 @@ __i915_read(64, q)
 
 #define __i915_write(x, y) \
 void i915_write##x(struct drm_i915_private *dev_priv, u32 reg, u##x val) { \
+	unsigned long irqflags; \
 	u32 __fifo_ret = 0; \
 	trace_i915_reg_rw(true, reg, val, sizeof(val)); \
+	spin_lock_irqsave(&dev_priv->gt_lock, irqflags); \
 	if (NEEDS_FORCE_WAKE((dev_priv), (reg))) { \
 		__fifo_ret = __gen6_gt_wait_for_fifo(dev_priv); \
 	} \
@@ -1293,6 +1295,7 @@ void i915_write##x(struct drm_i915_private *dev_priv, u32 reg, u##x val) { \
 		gen6_gt_check_fifodbg(dev_priv); \
 	} \
 	hsw_unclaimed_reg_check(dev_priv, reg); \
+	spin_unlock_irqrestore(&dev_priv->gt_lock, irqflags); \
 }
 __i915_write(8, b)
 __i915_write(16, w)

drivers/gpu/drm/i915/i915_drv.h

@@ -555,6 +555,7 @@ enum intel_sbi_destination {
 #define QUIRK_PIPEA_FORCE (1<<0)
 #define QUIRK_LVDS_SSC_DISABLE (1<<1)
 #define QUIRK_INVERT_BRIGHTNESS (1<<2)
+#define QUIRK_NO_PCH_PWM_ENABLE (1<<3)
 
 struct intel_fbdev;
 struct intel_fbc_work;
@@ -1583,7 +1584,7 @@ void i915_handle_error(struct drm_device *dev, bool wedged);
 extern void intel_irq_init(struct drm_device *dev);
 extern void intel_hpd_init(struct drm_device *dev);
 extern void intel_gt_init(struct drm_device *dev);
-extern void intel_gt_reset(struct drm_device *dev);
+extern void intel_gt_sanitize(struct drm_device *dev);
 
 void i915_error_state_free(struct kref *error_ref);
 

drivers/gpu/drm/i915/i915_gem.c

@@ -2258,7 +2258,17 @@ void i915_gem_restore_fences(struct drm_device *dev)
 
 	for (i = 0; i < dev_priv->num_fence_regs; i++) {
 		struct drm_i915_fence_reg *reg = &dev_priv->fence_regs[i];
-		i915_gem_write_fence(dev, i, reg->obj);
+
+		/*
+		 * Commit delayed tiling changes if we have an object still
+		 * attached to the fence, otherwise just clear the fence.
+		 */
+		if (reg->obj) {
+			i915_gem_object_update_fence(reg->obj, reg,
+						     reg->obj->tiling_mode);
+		} else {
+			i915_gem_write_fence(dev, i, NULL);
+		}
 	}
 }
 
@@ -2795,6 +2805,10 @@ static void i915_gem_write_fence(struct drm_device *dev, int reg,
 	if (i915_gem_object_needs_mb(dev_priv->fence_regs[reg].obj))
 		mb();
 
+	WARN(obj && (!obj->stride || !obj->tiling_mode),
+	     "bogus fence setup with stride: 0x%x, tiling mode: %i\n",
+	     obj->stride, obj->tiling_mode);
+
 	switch (INTEL_INFO(dev)->gen) {
 	case 7:
 	case 6:
@@ -2836,6 +2850,7 @@ static void i915_gem_object_update_fence(struct drm_i915_gem_object *obj,
 		fence->obj = NULL;
 		list_del_init(&fence->lru_list);
 	}
+	obj->fence_dirty = false;
 }
 
 static int
@@ -2965,7 +2980,6 @@ i915_gem_object_get_fence(struct drm_i915_gem_object *obj)
 		return 0;
 
 	i915_gem_object_update_fence(obj, reg, enable);
-	obj->fence_dirty = false;
 
 	return 0;
 }

drivers/gpu/drm/i915/intel_ddi.c

@@ -301,7 +301,7 @@ static void intel_ddi_mode_set(struct drm_encoder *encoder,
 		struct intel_digital_port *intel_dig_port =
 			enc_to_dig_port(encoder);
 
-		intel_dp->DP = intel_dig_port->port_reversal |
+		intel_dp->DP = intel_dig_port->saved_port_bits |
 			       DDI_BUF_CTL_ENABLE | DDI_BUF_EMP_400MV_0DB_HSW;
 		intel_dp->DP |= DDI_PORT_WIDTH(intel_dp->lane_count);
 
@@ -1109,7 +1109,8 @@ static void intel_enable_ddi(struct intel_encoder *intel_encoder)
 		 * enabling the port.
 		 */
 		I915_WRITE(DDI_BUF_CTL(port),
-			   intel_dig_port->port_reversal | DDI_BUF_CTL_ENABLE);
+			   intel_dig_port->saved_port_bits |
+			   DDI_BUF_CTL_ENABLE);
 	} else if (type == INTEL_OUTPUT_EDP) {
 		struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
 
@@ -1347,8 +1348,9 @@ void intel_ddi_init(struct drm_device *dev, enum port port)
 	intel_encoder->get_config = intel_ddi_get_config;
 
 	intel_dig_port->port = port;
-	intel_dig_port->port_reversal = I915_READ(DDI_BUF_CTL(port)) &
-					DDI_BUF_PORT_REVERSAL;
+	intel_dig_port->saved_port_bits = I915_READ(DDI_BUF_CTL(port)) &
+					  (DDI_BUF_PORT_REVERSAL |
+					   DDI_A_4_LANES);
 	intel_dig_port->dp.output_reg = DDI_BUF_CTL(port);
 
 	intel_encoder->type = INTEL_OUTPUT_UNKNOWN;

drivers/gpu/drm/i915/intel_display.c

@@ -4913,22 +4913,19 @@ static void i9xx_get_pfit_config(struct intel_crtc *crtc,
 	uint32_t tmp;
 
 	tmp = I915_READ(PFIT_CONTROL);
+	if (!(tmp & PFIT_ENABLE))
+		return;
 
+	/* Check whether the pfit is attached to our pipe. */
 	if (INTEL_INFO(dev)->gen < 4) {
 		if (crtc->pipe != PIPE_B)
 			return;
-
-		/* gen2/3 store dither state in pfit control, needs to match */
-		pipe_config->gmch_pfit.control = tmp & PANEL_8TO6_DITHER_ENABLE;
 	} else {
 		if ((tmp & PFIT_PIPE_MASK) != (crtc->pipe << PFIT_PIPE_SHIFT))
 			return;
 	}
 
-	if (!(tmp & PFIT_ENABLE))
-		return;
-
-	pipe_config->gmch_pfit.control = I915_READ(PFIT_CONTROL);
+	pipe_config->gmch_pfit.control = tmp;
 	pipe_config->gmch_pfit.pgm_ratios = I915_READ(PFIT_PGM_RATIOS);
 	if (INTEL_INFO(dev)->gen < 5)
 		pipe_config->gmch_pfit.lvds_border_bits =
@@ -8317,6 +8314,8 @@ check_shared_dpll_state(struct drm_device *dev)
 		     pll->active, pll->refcount);
 		WARN(pll->active && !pll->on,
 		     "pll in active use but not on in sw tracking\n");
+		WARN(pll->on && !pll->active,
+		     "pll in on but not on in use in sw tracking\n");
 		WARN(pll->on != active,
 		     "pll on state mismatch (expected %i, found %i)\n",
 		     pll->on, active);
@@ -8541,15 +8540,20 @@ static void intel_set_config_restore_state(struct drm_device *dev,
 }
 
 static bool
-is_crtc_connector_off(struct drm_crtc *crtc, struct drm_connector *connectors,
-		      int num_connectors)
+is_crtc_connector_off(struct drm_mode_set *set)
 {
 	int i;
 
-	for (i = 0; i < num_connectors; i++)
-		if (connectors[i].encoder &&
-		    connectors[i].encoder->crtc == crtc &&
-		    connectors[i].dpms != DRM_MODE_DPMS_ON)
+	if (set->num_connectors == 0)
+		return false;
+
+	if (WARN_ON(set->connectors == NULL))
+		return false;
+
+	for (i = 0; i < set->num_connectors; i++)
+		if (set->connectors[i]->encoder &&
+		    set->connectors[i]->encoder->crtc == set->crtc &&
+		    set->connectors[i]->dpms != DRM_MODE_DPMS_ON)
 			return true;
 
 	return false;
@@ -8562,10 +8566,8 @@ intel_set_config_compute_mode_changes(struct drm_mode_set *set,
 
 	/* We should be able to check here if the fb has the same properties
 	 * and then just flip_or_move it */
-	if (set->connectors != NULL &&
-	    is_crtc_connector_off(set->crtc, *set->connectors,
-				  set->num_connectors)) {
-			config->mode_changed = true;
+	if (is_crtc_connector_off(set)) {
+		config->mode_changed = true;
 	} else if (set->crtc->fb != set->fb) {
 		/* If we have no fb then treat it as a full mode set */
 		if (set->crtc->fb == NULL) {
@@ -9398,6 +9400,17 @@ static void quirk_invert_brightness(struct drm_device *dev)
 	DRM_INFO("applying inverted panel brightness quirk\n");
 }
 
+/*
+ * Some machines (Dell XPS13) suffer broken backlight controls if
+ * BLM_PCH_PWM_ENABLE is set.
+ */
+static void quirk_no_pcm_pwm_enable(struct drm_device *dev)
+{
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	dev_priv->quirks |= QUIRK_NO_PCH_PWM_ENABLE;
+	DRM_INFO("applying no-PCH_PWM_ENABLE quirk\n");
+}
+
 struct intel_quirk {
 	int device;
 	int subsystem_vendor;
@@ -9467,6 +9480,11 @@ static struct intel_quirk intel_quirks[] = {
 
 	/* Acer Aspire 4736Z */
 	{ 0x2a42, 0x1025, 0x0260, quirk_invert_brightness },
+
+	/* Dell XPS13 HD Sandy Bridge */
+	{ 0x0116, 0x1028, 0x052e, quirk_no_pcm_pwm_enable },
+	/* Dell XPS13 HD and XPS13 FHD Ivy Bridge */
+	{ 0x0166, 0x1028, 0x058b, quirk_no_pcm_pwm_enable },
 };
 
 static void intel_init_quirks(struct drm_device *dev)
@@ -9817,8 +9835,8 @@ static void intel_modeset_readout_hw_state(struct drm_device *dev)
 		}
 		pll->refcount = pll->active;
 
-		DRM_DEBUG_KMS("%s hw state readout: refcount %i\n",
-			      pll->name, pll->refcount);
+		DRM_DEBUG_KMS("%s hw state readout: refcount %i, on %i\n",
+			      pll->name, pll->refcount, pll->on);
 	}
 
 	list_for_each_entry(encoder, &dev->mode_config.encoder_list,
@@ -9869,6 +9887,7 @@ void intel_modeset_setup_hw_state(struct drm_device *dev,
 	struct drm_plane *plane;
 	struct intel_crtc *crtc;
 	struct intel_encoder *encoder;
+	int i;
 
 	intel_modeset_readout_hw_state(dev);
 
@@ -9884,6 +9903,18 @@ void intel_modeset_setup_hw_state(struct drm_device *dev,
 		intel_dump_pipe_config(crtc, &crtc->config, "[setup_hw_state]");
 	}
 
+	for (i = 0; i < dev_priv->num_shared_dpll; i++) {
+		struct intel_shared_dpll *pll = &dev_priv->shared_dplls[i];
+
+		if (!pll->on || pll->active)
+			continue;
+
+		DRM_DEBUG_KMS("%s enabled but not in use, disabling\n", pll->name);
+
+		pll->disable(dev_priv, pll);
+		pll->on = false;
+	}
+
 	if (force_restore) {
 		/*
 		 * We need to use raw interfaces for restoring state to avoid

drivers/gpu/drm/i915/intel_drv.h

@@ -504,7 +504,7 @@ struct intel_dp {
 struct intel_digital_port {
 	struct intel_encoder base;
 	enum port port;
-	u32 port_reversal;
+	u32 saved_port_bits;
 	struct intel_dp dp;
 	struct intel_hdmi hdmi;
 };

drivers/gpu/drm/i915/intel_lvds.c

@@ -109,6 +109,13 @@ static void intel_lvds_get_config(struct intel_encoder *encoder,
 		flags |= DRM_MODE_FLAG_PVSYNC;
 
 	pipe_config->adjusted_mode.flags |= flags;
+
+	/* gen2/3 store dither state in pfit control, needs to match */
+	if (INTEL_INFO(dev)->gen < 4) {
+		tmp = I915_READ(PFIT_CONTROL);
+
+		pipe_config->gmch_pfit.control |= tmp & PANEL_8TO6_DITHER_ENABLE;
+	}
 }
 
 /* The LVDS pin pair needs to be on before the DPLLs are enabled.
@@ -290,14 +297,11 @@ static bool intel_lvds_compute_config(struct intel_encoder *intel_encoder,
 
 		intel_pch_panel_fitting(intel_crtc, pipe_config,
 					intel_connector->panel.fitting_mode);
-		return true;
 	} else {
 		intel_gmch_panel_fitting(intel_crtc, pipe_config,
 					 intel_connector->panel.fitting_mode);
-	}
 
-	drm_mode_set_crtcinfo(adjusted_mode, 0);
-	pipe_config->timings_set = true;
+	}
 
 	/*
 	 * XXX: It would be nice to support lower refresh rates on the

drivers/gpu/drm/i915/intel_panel.c

@@ -194,6 +194,9 @@ void intel_gmch_panel_fitting(struct intel_crtc *intel_crtc,
 	    adjusted_mode->vdisplay == mode->vdisplay)
 		goto out;
 
+	drm_mode_set_crtcinfo(adjusted_mode, 0);
+	pipe_config->timings_set = true;
+
 	switch (fitting_mode) {
 	case DRM_MODE_SCALE_CENTER:
 		/*
@@ -580,7 +583,8 @@ void intel_panel_enable_backlight(struct drm_device *dev,
 		POSTING_READ(reg);
 		I915_WRITE(reg, tmp | BLM_PWM_ENABLE);
 
-		if (HAS_PCH_SPLIT(dev)) {
+		if (HAS_PCH_SPLIT(dev) &&
+		    !(dev_priv->quirks & QUIRK_NO_PCH_PWM_ENABLE)) {
 			tmp = I915_READ(BLC_PWM_PCH_CTL1);
 			tmp |= BLM_PCH_PWM_ENABLE;
 			tmp &= ~BLM_PCH_OVERRIDE_ENABLE;