Merge tag 'for-linus-20121009' of git://git.infradead.org/mtd-2.6

Pull MTD updates from David Woodhouse: - Disable broken mtdchar mmap() on MMU systems - Additional ECC tests for NAND flash, and some test cleanups - New NAND and SPI chip support - Fixes/cleanup for SH FLCTL NAND controller driver - Improved hardware support for GPMI NAND controller - Conversions to device-tree support for various drivers - Removal of obsolete drivers (sbc8xxx, bcmring, etc.) - New LPC32xx drivers for MLC and SLC NAND - Further cleanup of NAND OOB/ECC handling - UAPI cleanup merge from David Howells (just moving files, since MTD headers were sorted out long ago to separate user-visible from kernel bits) * tag 'for-linus-20121009' of git://git.infradead.org/mtd-2.6: (168 commits) mtd: Disable mtdchar mmap on MMU systems UAPI: (Scripted) Disintegrate include/mtd mtd: nand: detect Samsung K9GBG08U0A, K9GAG08U0F ID mtd: nand: decode Hynix MLC, 6-byte ID length mtd: nand: increase max OOB size to 640 mtd: nand: add generic READ ID length calculation functions mtd: nand: split simple ID decode into its own function mtd: nand: split extended ID decoding into its own function mtd: nand: split BB marker options decoding into its own function mtd: nand: remove redundant ID read mtd: nand: remove unnecessary variable mtd: docg4: add missing HAS_IOMEM dependency mtd: gpmi: initialize the timing registers only one time mtd: gpmi: add EDO feature for imx6q mtd: gpmi: do not set the default values for the extra clocks mtd: gpmi: simplify the DLL setting code mtd: gpmi: add a new field for HW_GPMI_CTRL1 mtd: gpmi: do not get the clock frequency in gpmi_begin() mtd: gpmi: add a new field for HW_GPMI_TIMING1 mtd: add helpers to get the supportted ONFI timing mode ...
mariux64 · Oct 10, 2012 · 10f39f0 · 10f39f0
2 parents 7205542 + f5cf8f0
commit 10f39f0
Show file tree

Hide file tree

Showing 119 changed files with 6,361 additions and 3,239 deletions.
diff --git a/Documentation/DocBook/mtdnand.tmpl b/Documentation/DocBook/mtdnand.tmpl
@@ -1216,8 +1216,6 @@ in this page</entry>
 #define	NAND_BBT_LASTBLOCK	0x00000010
 /* The bbt is at the given page, else we must scan for the bbt */
 #define NAND_BBT_ABSPAGE	0x00000020
-/* The bbt is at the given page, else we must scan for the bbt */
-#define NAND_BBT_SEARCH		0x00000040
 /* bbt is stored per chip on multichip devices */
 #define NAND_BBT_PERCHIP	0x00000080
 /* bbt has a version counter at offset veroffs */

diff --git a/Documentation/devicetree/bindings/arm/davinci/nand.txt b/Documentation/devicetree/bindings/arm/davinci/nand.txt
@@ -0,0 +1,51 @@
+* Texas Instruments Davinci NAND
+
+This file provides information, what the device node for the
+davinci nand interface contain.
+
+Required properties:
+- compatible: "ti,davinci-nand";
+- reg : contain 2 offset/length values:
+        - offset and length for the access window
+        - offset and length for accessing the aemif control registers
+- ti,davinci-chipselect: Indicates on the davinci_nand driver which
+                         chipselect is used for accessing the nand.
+
+Recommended properties :
+- ti,davinci-mask-ale: mask for ale
+- ti,davinci-mask-cle: mask for cle
+- ti,davinci-mask-chipsel: mask for chipselect
+- ti,davinci-ecc-mode: ECC mode valid values for davinci driver:
+		- "none"
+		- "soft"
+		- "hw"
+- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4.
+- ti,davinci-nand-buswidth: buswidth 8 or 16
+- ti,davinci-nand-use-bbt: use flash based bad block table support.
+
+Example (enbw_cmc board):
+aemif@60000000 {
+	compatible = "ti,davinci-aemif";
+	#address-cells = <2>;
+	#size-cells = <1>;
+	reg = <0x68000000 0x80000>;
+	ranges = <2 0 0x60000000 0x02000000
+		  3 0 0x62000000 0x02000000
+		  4 0 0x64000000 0x02000000
+		  5 0 0x66000000 0x02000000
+		  6 0 0x68000000 0x02000000>;
+	nand@3,0 {
+		compatible = "ti,davinci-nand";
+		reg = <3 0x0 0x807ff
+			6 0x0 0x8000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ti,davinci-chipselect = <1>;
+		ti,davinci-mask-ale = <0>;
+		ti,davinci-mask-cle = <0>;
+		ti,davinci-mask-chipsel = <0>;
+		ti,davinci-ecc-mode = "hw";
+		ti,davinci-ecc-bits = <4>;
+		ti,davinci-nand-use-bbt;
+	};
+};
diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
@@ -3,7 +3,9 @@ Atmel NAND flash
 Required properties:
 - compatible : "atmel,at91rm9200-nand".
 - reg : should specify localbus address and size used for the chip,
-	and if availlable the ECC.
+	and hardware ECC controller if available.
+	If the hardware ECC is PMECC, it should contain address and size for
+	PMECC, PMECC Error Location controller and ROM which has lookup tables.
 - atmel,nand-addr-offset : offset for the address latch.
 - atmel,nand-cmd-offset : offset for the command latch.
 - #address-cells, #size-cells : Must be present if the device has sub-nodes
@@ -16,6 +18,15 @@ Optional properties:
 - nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default.
   Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
   "soft_bch".
+- atmel,has-pmecc : boolean to enable Programmable Multibit ECC hardware.
+  Only supported by at91sam9x5 or later sam9 product.
+- atmel,pmecc-cap : error correct capability for Programmable Multibit ECC
+  Controller. Supported values are: 2, 4, 8, 12, 24.
+- atmel,pmecc-sector-size : sector size for ECC computation. Supported values
+  are: 512, 1024.
+- atmel,pmecc-lookup-table-offset : includes two offsets of lookup table in ROM
+  for different sector size. First one is for sector size 512, the next is for
+  sector size 1024.
 - nand-bus-width : 8 or 16 bus width if not present 8
 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
 
@@ -39,3 +50,30 @@ nand0: nand@40000000,0 {
 		...
 	};
 };
+
+/* for PMECC supported chips */
+nand0: nand@40000000 {
+	compatible = "atmel,at91rm9200-nand";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	reg = < 0x40000000 0x10000000	/* bus addr & size */
+		0xffffe000 0x00000600	/* PMECC addr & size */
+		0xffffe600 0x00000200	/* PMECC ERRLOC addr & size */
+		0x00100000 0x00100000	/* ROM addr & size */
+		>;
+	atmel,nand-addr-offset = <21>;	/* ale */
+	atmel,nand-cmd-offset = <22>;	/* cle */
+	nand-on-flash-bbt;
+	nand-ecc-mode = "hw";
+	atmel,has-pmecc;	/* enable PMECC */
+	atmel,pmecc-cap = <2>;
+	atmel,pmecc-sector-size = <512>;
+	atmel,pmecc-lookup-table-offset = <0x8000 0x10000>;
+	gpios = <&pioD 5 0	/* rdy */
+		 &pioD 4 0	/* nce */
+		 0		/* cd */
+		>;
+	partition@0 {
+		...
+	};
+};
diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt
@@ -12,6 +12,10 @@ Required properties:
   - interrupt-names : The interrupt names "gpmi-dma", "bch";
   - fsl,gpmi-dma-channel : Should contain the dma channel it uses.
 
+Optional properties:
+  - nand-on-flash-bbt: boolean to enable on flash bbt option if not
+                       present false
+
 The device tree may optionally contain sub-nodes describing partitions of the
 address space. See partition.txt for more detail.
 

diff --git a/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt b/Documentation/devicetree/bindings/mtd/lpc32xx-mlc.txt
@@ -0,0 +1,50 @@
+NXP LPC32xx SoC NAND MLC controller
+
+Required properties:
+- compatible: "nxp,lpc3220-mlc"
+- reg: Address and size of the controller
+- interrupts: The NAND interrupt specification
+- gpios: GPIO specification for NAND write protect
+
+The following required properties are very controller specific. See the LPC32xx
+User Manual 7.5.14 MLC NAND Timing Register (the values here are specified in
+Hz, to make them independent of actual clock speed and to provide for good
+accuracy:)
+- nxp,tcea_delay: TCEA_DELAY
+- nxp,busy_delay: BUSY_DELAY
+- nxp,nand_ta: NAND_TA
+- nxp,rd_high: RD_HIGH
+- nxp,rd_low: RD_LOW
+- nxp,wr_high: WR_HIGH
+- nxp,wr_low: WR_LOW
+
+Optional subnodes:
+- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt
+
+Example:
+
+	mlc: flash@200A8000 {
+		compatible = "nxp,lpc3220-mlc";
+		reg = <0x200A8000 0x11000>;
+		interrupts = <11 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nxp,tcea-delay = <333333333>;
+		nxp,busy-delay = <10000000>;
+		nxp,nand-ta = <18181818>;
+		nxp,rd-high = <31250000>;
+		nxp,rd-low = <45454545>;
+		nxp,wr-high = <40000000>;
+		nxp,wr-low = <83333333>;
+		gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
+		mtd0@00000000 {
+			label = "boot";
+			reg = <0x00000000 0x00064000>;
+			read-only;
+		};
+
+		...
+
+	};
diff --git a/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt b/Documentation/devicetree/bindings/mtd/lpc32xx-slc.txt
@@ -0,0 +1,52 @@
+NXP LPC32xx SoC NAND SLC controller
+
+Required properties:
+- compatible: "nxp,lpc3220-slc"
+- reg: Address and size of the controller
+- nand-on-flash-bbt: Use bad block table on flash
+- gpios: GPIO specification for NAND write protect
+
+The following required properties are very controller specific. See the LPC32xx
+User Manual:
+- nxp,wdr-clks: Delay before Ready signal is tested on write (W_RDY)
+- nxp,rdr-clks: Delay before Ready signal is tested on read (R_RDY)
+(The following values are specified in Hz, to make them independent of actual
+clock speed:)
+- nxp,wwidth: Write pulse width (W_WIDTH)
+- nxp,whold: Write hold time (W_HOLD)
+- nxp,wsetup: Write setup time (W_SETUP)
+- nxp,rwidth: Read pulse width (R_WIDTH)
+- nxp,rhold: Read hold time (R_HOLD)
+- nxp,rsetup: Read setup time (R_SETUP)
+
+Optional subnodes:
+- Partitions, see Documentation/devicetree/bindings/mtd/partition.txt
+
+Example:
+
+	slc: flash@20020000 {
+		compatible = "nxp,lpc3220-slc";
+		reg = <0x20020000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nxp,wdr-clks = <14>;
+		nxp,wwidth = <40000000>;
+		nxp,whold = <100000000>;
+		nxp,wsetup = <100000000>;
+		nxp,rdr-clks = <14>;
+		nxp,rwidth = <40000000>;
+		nxp,rhold = <66666666>;
+		nxp,rsetup = <100000000>;
+		nand-on-flash-bbt;
+		gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
+
+		mtd0@00000000 {
+			label = "phy3250-boot";
+			reg = <0x00000000 0x00064000>;
+			read-only;
+		};
+
+		...
+
+	};
diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt
@@ -16,6 +16,13 @@ file systems on embedded devices.
  - #address-cells, #size-cells : Must be present if the device has
    sub-nodes representing partitions (see below).  In this case
    both #address-cells and #size-cells must be equal to 1.
+ - no-unaligned-direct-access: boolean to disable the default direct
+   mapping of the flash.
+   On some platforms (e.g. MPC5200) a direct 1:1 mapping may cause
+   problems with JFFS2 usage, as the local bus (LPB) doesn't support
+   unaligned accesses as implemented in the JFFS2 code via memcpy().
+   By defining "no-unaligned-direct-access", the flash will not be
+   exposed directly to the MTD users (e.g. JFFS2) any more.
 
 For JEDEC compatible devices, the following additional properties
 are defined:

diff --git a/arch/arm/boot/dts/imx51.dtsi b/arch/arm/boot/dts/imx51.dtsi
@@ -407,6 +407,13 @@
 				status = "disabled";
 			};
 
+			nand@83fdb000 {
+				compatible = "fsl,imx51-nand";
+				reg = <0x83fdb000 0x1000 0xcfff0000 0x10000>;
+				interrupts = <8>;
+				status = "disabled";
+			};
+
 			ssi3: ssi@83fe8000 {
 				compatible = "fsl,imx51-ssi", "fsl,imx21-ssi";
 				reg = <0x83fe8000 0x4000>;

diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/imx53.dtsi
@@ -518,6 +518,13 @@
 				status = "disabled";
 			};
 
+			nand@63fdb000 {
+				compatible = "fsl,imx53-nand";
+				reg = <0x63fdb000 0x1000 0xf7ff0000 0x10000>;
+				interrupts = <8>;
+				status = "disabled";
+			};
+
 			ssi3: ssi@63fe8000 {
 				compatible = "fsl,imx53-ssi", "fsl,imx21-ssi";
 				reg = <0x63fe8000 0x4000>;

diff --git a/arch/arm/configs/cam60_defconfig b/arch/arm/configs/cam60_defconfig
@@ -49,7 +49,6 @@ CONFIG_MTD_COMPLEX_MAPPINGS=y
 CONFIG_MTD_PLATRAM=m
 CONFIG_MTD_DATAFLASH=y
 CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_VERIFY_WRITE=y
 CONFIG_MTD_NAND_ATMEL=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y

diff --git a/arch/arm/configs/corgi_defconfig b/arch/arm/configs/corgi_defconfig
@@ -97,7 +97,6 @@ CONFIG_MTD_BLOCK=y
 CONFIG_MTD_ROM=y
 CONFIG_MTD_COMPLEX_MAPPINGS=y
 CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_VERIFY_WRITE=y
 CONFIG_MTD_NAND_SHARPSL=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_IDE=y

diff --git a/arch/arm/configs/ep93xx_defconfig b/arch/arm/configs/ep93xx_defconfig
@@ -61,7 +61,6 @@ CONFIG_MTD_CFI_STAA=y
 CONFIG_MTD_ROM=y
 CONFIG_MTD_PHYSMAP=y
 CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_VERIFY_WRITE=y
 CONFIG_BLK_DEV_NBD=y
 CONFIG_EEPROM_LEGACY=y
 CONFIG_SCSI=y

diff --git a/arch/arm/configs/mini2440_defconfig b/arch/arm/configs/mini2440_defconfig
@@ -102,7 +102,6 @@ CONFIG_MTD_CFI_STAA=y
 CONFIG_MTD_RAM=y
 CONFIG_MTD_ROM=y
 CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_VERIFY_WRITE=y
 CONFIG_MTD_NAND_S3C2410=y
 CONFIG_MTD_NAND_PLATFORM=y
 CONFIG_MTD_LPDDR=y

diff --git a/arch/arm/configs/mv78xx0_defconfig b/arch/arm/configs/mv78xx0_defconfig
@@ -49,7 +49,6 @@ CONFIG_MTD_CFI_INTELEXT=y
 CONFIG_MTD_CFI_AMDSTD=y
 CONFIG_MTD_PHYSMAP=y
 CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_VERIFY_WRITE=y
 CONFIG_MTD_NAND_ORION=y
 CONFIG_BLK_DEV_LOOP=y
 # CONFIG_SCSI_PROC_FS is not set

diff --git a/arch/arm/configs/nhk8815_defconfig b/arch/arm/configs/nhk8815_defconfig
@@ -57,7 +57,6 @@ CONFIG_MTD_CHAR=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_ECC_SMC=y
-CONFIG_MTD_NAND_VERIFY_WRITE=y
 CONFIG_MTD_NAND_NOMADIK=y
 CONFIG_MTD_ONENAND=y
 CONFIG_MTD_ONENAND_VERIFY_WRITE=y

diff --git a/arch/arm/configs/orion5x_defconfig b/arch/arm/configs/orion5x_defconfig
@@ -72,7 +72,6 @@ CONFIG_MTD_CFI_INTELEXT=y
 CONFIG_MTD_CFI_AMDSTD=y
 CONFIG_MTD_PHYSMAP=y
 CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_VERIFY_WRITE=y
 CONFIG_MTD_NAND_PLATFORM=y
 CONFIG_MTD_NAND_ORION=y
 CONFIG_BLK_DEV_LOOP=y

diff --git a/arch/arm/configs/pxa3xx_defconfig b/arch/arm/configs/pxa3xx_defconfig
@@ -36,7 +36,6 @@ CONFIG_MTD_CONCAT=y
 CONFIG_MTD_CHAR=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_VERIFY_WRITE=y
 CONFIG_MTD_NAND_PXA3xx=y
 CONFIG_MTD_NAND_PXA3xx_BUILTIN=y
 CONFIG_MTD_ONENAND=y

diff --git a/arch/arm/configs/spitz_defconfig b/arch/arm/configs/spitz_defconfig
@@ -94,7 +94,6 @@ CONFIG_MTD_BLOCK=y
 CONFIG_MTD_ROM=y
 CONFIG_MTD_COMPLEX_MAPPINGS=y
 CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_VERIFY_WRITE=y
 CONFIG_MTD_NAND_SHARPSL=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_IDE=y

diff --git a/arch/arm/mach-clps711x/autcpu12.c b/arch/arm/mach-clps711x/autcpu12.c
@@ -23,6 +23,8 @@
 #include <linux/string.h>
 #include <linux/mm.h>
 #include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/platform_device.h>
 
 #include <mach/hardware.h>
 #include <asm/sizes.h>
@@ -62,9 +64,26 @@ void __init autcpu12_map_io(void)
         iotable_init(autcpu12_io_desc, ARRAY_SIZE(autcpu12_io_desc));
 }
 
+static struct resource autcpu12_nvram_resource[] __initdata = {
+	DEFINE_RES_MEM_NAMED(AUTCPU12_PHYS_NVRAM, SZ_128K, "SRAM"),
+};
+
+static struct platform_device autcpu12_nvram_pdev __initdata = {
+	.name		= "autcpu12_nvram",
+	.id		= -1,
+	.resource	= autcpu12_nvram_resource,
+	.num_resources	= ARRAY_SIZE(autcpu12_nvram_resource),
+};
+
+static void __init autcpu12_init(void)
+{
+	platform_device_register(&autcpu12_nvram_pdev);
+}
+
 MACHINE_START(AUTCPU12, "autronix autcpu12")
 	/* Maintainer: Thomas Gleixner */
 	.atag_offset	= 0x20000,
+	.init_machine	= autcpu12_init,
 	.map_io		= autcpu12_map_io,
 	.init_irq	= clps711x_init_irq,
 	.timer		= &clps711x_timer,

diff --git a/arch/arm/mach-imx/clk-imx51-imx53.c b/arch/arm/mach-imx/clk-imx51-imx53.c
@@ -369,6 +369,7 @@ int __init mx51_clocks_init(unsigned long rate_ckil, unsigned long rate_osc,
 	clk_register_clkdev(clk[ssi1_ipg_gate], NULL, "83fcc000.ssi");
 	clk_register_clkdev(clk[ssi2_ipg_gate], NULL, "70014000.ssi");
 	clk_register_clkdev(clk[ssi3_ipg_gate], NULL, "83fe8000.ssi");
+	clk_register_clkdev(clk[nfc_gate], NULL, "83fdb000.nand");
 
 	/* set the usboh3 parent to pll2_sw */
 	clk_set_parent(clk[usboh3_sel], clk[pll2_sw]);
@@ -461,6 +462,7 @@ int __init mx53_clocks_init(unsigned long rate_ckil, unsigned long rate_osc,
 	clk_register_clkdev(clk[ssi1_ipg_gate], NULL, "63fcc000.ssi");
 	clk_register_clkdev(clk[ssi2_ipg_gate], NULL, "50014000.ssi");
 	clk_register_clkdev(clk[ssi3_ipg_gate], NULL, "63fd0000.ssi");
+	clk_register_clkdev(clk[nfc_gate], NULL, "63fdb000.nand");
 	clk_register_clkdev(clk[can1_ipg_gate], "ipg", "53fc8000.can");
 	clk_register_clkdev(clk[can1_serial_gate], "per", "53fc8000.can");
 	clk_register_clkdev(clk[can2_ipg_gate], "ipg", "53fcc000.can");