Merge drm-fixes-for-v4.17-rc6-urgent into drm-next

Need to backmerge some nouveau fixes to reduce the nouveau -next conflicts a lot. Signed-off-by: Dave Airlie <airlied@redhat.com>
mariux64 · May 18, 2018 · 1fafef9 · 1fafef9
2 parents 315852b + 76ef6b2
commit 1fafef9
Show file tree

Hide file tree

Showing 559 changed files with 4,018 additions and 2,246 deletions.
diff --git a/Documentation/admin-guide/pm/intel_pstate.rst b/Documentation/admin-guide/pm/intel_pstate.rst
@@ -145,7 +145,7 @@ feature enabled.]
 
 In this mode ``intel_pstate`` registers utilization update callbacks with the
 CPU scheduler in order to run a P-state selection algorithm, either
-``powersave`` or ``performance``, depending on the ``scaling_cur_freq`` policy
+``powersave`` or ``performance``, depending on the ``scaling_governor`` policy
 setting in ``sysfs``.  The current CPU frequency information to be made
 available from the ``scaling_cur_freq`` policy attribute in ``sysfs`` is
 periodically updated by those utilization update callbacks too.

diff --git a/Documentation/admin-guide/pm/sleep-states.rst b/Documentation/admin-guide/pm/sleep-states.rst
@@ -15,7 +15,7 @@ Sleep States That Can Be Supported
 ==================================
 
 Depending on its configuration and the capabilities of the platform it runs on,
-the Linux kernel can support up to four system sleep states, includig
+the Linux kernel can support up to four system sleep states, including
 hibernation and up to three variants of system suspend.  The sleep states that
 can be supported by the kernel are listed below.
 

diff --git a/Documentation/bpf/bpf_devel_QA.txt b/Documentation/bpf/bpf_devel_QA.txt
@@ -557,6 +557,14 @@ A: Although LLVM IR generation and optimization try to stay architecture
        pulls in some header files containing file scope host assembly codes.
      - You can add "-fno-jump-tables" to work around the switch table issue.
 
-   Otherwise, you can use bpf target.
+   Otherwise, you can use bpf target. Additionally, you _must_ use bpf target
+   when:
+
+     - Your program uses data structures with pointer or long / unsigned long
+       types that interface with BPF helpers or context data structures. Access
+       into these structures is verified by the BPF verifier and may result
+       in verification failures if the native architecture is not aligned with
+       the BPF architecture, e.g. 64-bit. An example of this is
+       BPF_PROG_TYPE_SK_MSG require '-target bpf'
 
 Happy BPF hacking!
diff --git a/Documentation/device-mapper/thin-provisioning.txt b/Documentation/device-mapper/thin-provisioning.txt
@@ -264,7 +264,10 @@ i) Constructor
 			   data device, but just remove the mapping.
 
       read_only: Don't allow any changes to be made to the pool
-		 metadata.
+		 metadata.  This mode is only available after the
+		 thin-pool has been created and first used in full
+		 read/write mode.  It cannot be specified on initial
+		 thin-pool creation.
 
       error_if_no_space: Error IOs, instead of queueing, if no space.
 

diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt
@@ -30,7 +30,6 @@ compatible:
 Optional properties:
 - dma-coherent      : Present if dma operations are coherent
 - clocks            : a list of phandle + clock specifier pairs
-- resets            : a list of phandle + reset specifier pairs
 - target-supply     : regulator for SATA target power
 - phys              : reference to the SATA PHY node
 - phy-names         : must be "sata-phy"

diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.txt b/Documentation/devicetree/bindings/display/panel/panel-common.txt
@@ -38,7 +38,7 @@ Display Timings
   require specific display timings. The panel-timing subnode expresses those
   timings as specified in the timing subnode section of the display timing
   bindings defined in
-  Documentation/devicetree/bindings/display/display-timing.txt.
+  Documentation/devicetree/bindings/display/panel/display-timing.txt.
 
 
 Connectivity

diff --git a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt
@@ -26,6 +26,7 @@ Required Properties:
 		- "renesas,dmac-r8a7794" (R-Car E2)
 		- "renesas,dmac-r8a7795" (R-Car H3)
 		- "renesas,dmac-r8a7796" (R-Car M3-W)
+		- "renesas,dmac-r8a77965" (R-Car M3-N)
 		- "renesas,dmac-r8a77970" (R-Car V3M)
 		- "renesas,dmac-r8a77980" (R-Car V3H)
 

diff --git a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt
@@ -4,6 +4,13 @@ Required properties:
 - compatible:
     atmel,maxtouch
 
+    The following compatibles have been used in various products but are
+    deprecated:
+	atmel,qt602240_ts
+	atmel,atmel_mxt_ts
+	atmel,atmel_mxt_tp
+	atmel,mXT224
+
 - reg: The I2C address of the device
 
 - interrupts: The sink for the touchpad's IRQ output

diff --git a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt
@@ -5,7 +5,9 @@ Required properties:
 - compatible: Must contain one or more of the following:
   - "renesas,rcar-gen3-canfd" for R-Car Gen3 compatible controller.
   - "renesas,r8a7795-canfd" for R8A7795 (R-Car H3) compatible controller.
-  - "renesas,r8a7796-canfd" for R8A7796 (R-Car M3) compatible controller.
+  - "renesas,r8a7796-canfd" for R8A7796 (R-Car M3-W) compatible controller.
+  - "renesas,r8a77970-canfd" for R8A77970 (R-Car V3M) compatible controller.
+  - "renesas,r8a77980-canfd" for R8A77980 (R-Car V3H) compatible controller.
 
   When compatible with the generic version, nodes must list the
   SoC-specific version corresponding to the platform first, followed by the

diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt
@@ -18,6 +18,7 @@ Required properties:
 
       - "renesas,etheravb-r8a7795" for the R8A7795 SoC.
       - "renesas,etheravb-r8a7796" for the R8A7796 SoC.
+      - "renesas,etheravb-r8a77965" for the R8A77965 SoC.
       - "renesas,etheravb-r8a77970" for the R8A77970 SoC.
       - "renesas,etheravb-r8a77980" for the R8A77980 SoC.
       - "renesas,etheravb-r8a77995" for the R8A77995 SoC.

diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
@@ -56,9 +56,9 @@ pins it needs, and how they should be configured, with regard to muxer
 configuration, drive strength and pullups. If one of these options is
 not set, its actual value will be unspecified.
 
-This driver supports the generic pin multiplexing and configuration
-bindings. For details on each properties, you can refer to
-./pinctrl-bindings.txt.
+Allwinner A1X Pin Controller supports the generic pin multiplexing and
+configuration bindings. For details on each properties, you can refer to
+ ./pinctrl-bindings.txt.
 
 Required sub-node properties:
   - pins

diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt
@@ -43,6 +43,8 @@ Required properties:
     - "renesas,hscif-r8a7795" for R8A7795 (R-Car H3) HSCIF compatible UART.
     - "renesas,scif-r8a7796" for R8A7796 (R-Car M3-W) SCIF compatible UART.
     - "renesas,hscif-r8a7796" for R8A7796 (R-Car M3-W) HSCIF compatible UART.
+    - "renesas,scif-r8a77965" for R8A77965 (R-Car M3-N) SCIF compatible UART.
+    - "renesas,hscif-r8a77965" for R8A77965 (R-Car M3-N) HSCIF compatible UART.
     - "renesas,scif-r8a77970" for R8A77970 (R-Car V3M) SCIF compatible UART.
     - "renesas,hscif-r8a77970" for R8A77970 (R-Car V3M) HSCIF compatible UART.
     - "renesas,scif-r8a77980" for R8A77980 (R-Car V3H) SCIF compatible UART.

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -182,6 +182,7 @@ karo	Ka-Ro electronics GmbH
 keithkoep	Keith & Koep GmbH
 keymile	Keymile GmbH
 khadas	Khadas
+kiebackpeter    Kieback & Peter GmbH
 kinetic Kinetic Technologies
 kingnovel	Kingnovel Technology Co., Ltd.
 kosagi	Sutajio Ko-Usagi PTE Ltd.

diff --git a/Documentation/devicetree/overlay-notes.txt b/Documentation/devicetree/overlay-notes.txt
@@ -98,6 +98,14 @@ Finally, if you need to remove all overlays in one-go, just call
 of_overlay_remove_all() which will remove every single one in the correct
 order.
 
+In addition, there is the option to register notifiers that get called on
+overlay operations. See of_overlay_notifier_register/unregister and
+enum of_overlay_notify_action for details.
+
+Note that a notifier callback is not supposed to store pointers to a device
+tree node or its content beyond OF_OVERLAY_POST_REMOVE corresponding to the
+respective node it received.
+
 Overlay DTS Format
 ------------------
 

diff --git a/Documentation/doc-guide/parse-headers.rst b/Documentation/doc-guide/parse-headers.rst
@@ -177,14 +177,14 @@ BUGS
 ****
 
 
-Report bugs to Mauro Carvalho Chehab <mchehab@s-opensource.com>
+Report bugs to Mauro Carvalho Chehab <mchehab@kernel.org>
 
 
 COPYRIGHT
 *********
 
 
-Copyright (c) 2016 by Mauro Carvalho Chehab <mchehab@s-opensource.com>.
+Copyright (c) 2016 by Mauro Carvalho Chehab <mchehab+samsung@kernel.org>.
 
 License GPLv2: GNU GPL version 2 <http://gnu.org/licenses/gpl.html>.
 

diff --git a/Documentation/media/uapi/rc/keytable.c.rst b/Documentation/media/uapi/rc/keytable.c.rst
@@ -7,7 +7,7 @@ file: uapi/v4l/keytable.c
 
     /* keytable.c - This program allows checking/replacing keys at IR
 
-       Copyright (C) 2006-2009 Mauro Carvalho Chehab <mchehab@infradead.org>
+       Copyright (C) 2006-2009 Mauro Carvalho Chehab <mchehab@kernel.org>
 
        This program is free software; you can redistribute it and/or modify
        it under the terms of the GNU General Public License as published by

diff --git a/Documentation/media/uapi/v4l/v4l2grab.c.rst b/Documentation/media/uapi/v4l/v4l2grab.c.rst
@@ -6,7 +6,7 @@ file: media/v4l/v4l2grab.c
 .. code-block:: c
 
     /* V4L2 video picture grabber
-       Copyright (C) 2009 Mauro Carvalho Chehab <mchehab@infradead.org>
+       Copyright (C) 2009 Mauro Carvalho Chehab <mchehab@kernel.org>
 
        This program is free software; you can redistribute it and/or modify
        it under the terms of the GNU General Public License as published by

diff --git a/Documentation/sphinx/parse-headers.pl b/Documentation/sphinx/parse-headers.pl
@@ -387,11 +387,11 @@ =head1 DESCRIPTION
 
 =head1 BUGS
 
-Report bugs to Mauro Carvalho Chehab <mchehab@s-opensource.com>
+Report bugs to Mauro Carvalho Chehab <mchehab@kernel.org>
 
 =head1 COPYRIGHT
 
-Copyright (c) 2016 by Mauro Carvalho Chehab <mchehab@s-opensource.com>.
+Copyright (c) 2016 by Mauro Carvalho Chehab <mchehab+samsung@kernel.org>.
 
 License GPLv2: GNU GPL version 2 <http://gnu.org/licenses/gpl.html>.
 

diff --git a/Documentation/translations/zh_CN/video4linux/v4l2-framework.txt b/Documentation/translations/zh_CN/video4linux/v4l2-framework.txt
@@ -6,15 +6,15 @@ communicating in English you can also ask the Chinese maintainer for
 help.  Contact the Chinese maintainer if this translation is outdated
 or if there is a problem with the translation.
 
-Maintainer: Mauro Carvalho Chehab <mchehab@infradead.org>
+Maintainer: Mauro Carvalho Chehab <mchehab@kernel.org>
 Chinese maintainer: Fu Wei <tekkamanninja@gmail.com>
 ---------------------------------------------------------------------
 Documentation/video4linux/v4l2-framework.txt 的中文翻译
 
 如果想评论或更新本文的内容，请直接联系原文档的维护者。如果你使用英文
 交流有困难的话，也可以向中文版维护者求助。如果本翻译更新不及时或者翻
 译存在问题，请联系中文版维护者。
-英文版维护者： Mauro Carvalho Chehab <mchehab@infradead.org>
+英文版维护者： Mauro Carvalho Chehab <mchehab@kernel.org>
 中文版维护者： 傅炜 Fu Wei <tekkamanninja@gmail.com>
 中文版翻译者： 傅炜 Fu Wei <tekkamanninja@gmail.com>
 中文版校译者： 傅炜 Fu Wei <tekkamanninja@gmail.com>