Merge branches 'thermal-core-fix', 'thermal-soc' and 'thermal-int340x…

…' into next

Documentation/devicetree/bindings/thermal/armada-thermal.txt

@@ -5,17 +5,9 @@ Required properties:
 - compatible:	Should be set to one of the following:
 		marvell,armada370-thermal
 		marvell,armada375-thermal
-		marvell,armada375-z1-thermal
 		marvell,armada380-thermal
 		marvell,armadaxp-thermal
 
-		Note: As the name suggests, "marvell,armada375-z1-thermal"
-		applies for the SoC Z1 stepping only. On such stepping
-		some quirks need to be done and the register offset differs
-		from the one in the A0 stepping.
-		The operating system may auto-detect the SoC stepping and
-		update the compatible and register offsets at runtime.
-
 - reg:		Device's register space.
 		Two entries are expected, see the examples below.
 		The first one is required for the sensor register;

Documentation/devicetree/bindings/thermal/rockchip-thermal.txt

@@ -0,0 +1,68 @@
+* Temperature Sensor ADC (TSADC) on rockchip SoCs
+
+Required properties:
+- compatible : "rockchip,rk3288-tsadc"
+- reg : physical base address of the controller and length of memory mapped
+	region.
+- interrupts : The interrupt number to the cpu. The interrupt specifier format
+	       depends on the interrupt controller.
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Shall be "tsadc" for the converter-clock, and "apb_pclk" for
+		the peripheral clock.
+- resets : Must contain an entry for each entry in reset-names.
+	   See ../reset/reset.txt for details.
+- reset-names : Must include the name "tsadc-apb".
+- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description.
+- rockchip,hw-tshut-temp : The hardware-controlled shutdown temperature value.
+- rockchip,hw-tshut-mode : The hardware-controlled shutdown mode 0:CRU 1:GPIO.
+- rockchip,hw-tshut-polarity : The hardware-controlled active polarity 0:LOW
+			       1:HIGH.
+
+Exiample:
+tsadc: tsadc@ff280000 {
+	compatible = "rockchip,rk3288-tsadc";
+	reg = <0xff280000 0x100>;
+	interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>;
+	clock-names = "tsadc", "apb_pclk";
+	resets = <&cru SRST_TSADC>;
+	reset-names = "tsadc-apb";
+	pinctrl-names = "default";
+	pinctrl-0 = <&otp_out>;
+	#thermal-sensor-cells = <1>;
+	rockchip,hw-tshut-temp = <95000>;
+	rockchip,hw-tshut-mode = <0>;
+	rockchip,hw-tshut-polarity = <0>;
+};
+
+Example: referring to thermal sensors:
+thermal-zones {
+	cpu_thermal: cpu_thermal {
+		polling-delay-passive = <1000>; /* milliseconds */
+		polling-delay = <5000>; /* milliseconds */
+
+		/* sensor	ID */
+		thermal-sensors = <&tsadc	1>;
+
+		trips {
+			cpu_alert0: cpu_alert {
+				temperature = <70000>; /* millicelsius */
+				hysteresis = <2000>; /* millicelsius */
+				type = "passive";
+			};
+			cpu_crit: cpu_crit {
+				temperature = <90000>; /* millicelsius */
+				hysteresis = <2000>; /* millicelsius */
+				type = "critical";
+			};
+		};
+
+		cooling-maps {
+			map0 {
+				trip = <&cpu_alert0>;
+				cooling-device =
+				    <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+	};
+};

Documentation/devicetree/bindings/thermal/tegra-soctherm.txt

@@ -0,0 +1,53 @@
+Tegra124 SOCTHERM thermal management system
+
+The SOCTHERM IP block contains thermal sensors, support for polled
+or interrupt-based thermal monitoring, CPU and GPU throttling based
+on temperature trip points, and handling external overcurrent
+notifications. It is also used to manage emergency shutdown in an
+overheating situation.
+
+Required properties :
+- compatible : "nvidia,tegra124-soctherm".
+- reg : Should contain 1 entry:
+  - SOCTHERM register set
+- interrupts : Defines the interrupt used by SOCTHERM
+- clocks : Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names : Must include the following entries:
+  - tsensor
+  - soctherm
+- resets : Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names : Must include the following entries:
+  - soctherm
+- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description
+    of this property. See <dt-bindings/thermal/tegra124-soctherm.h> for a
+    list of valid values when referring to thermal sensors.
+
+
+Example :
+
+	soctherm@0,700e2000 {
+		compatible = "nvidia,tegra124-soctherm";
+		reg = <0x0 0x700e2000 0x0 0x1000>;
+		interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&tegra_car TEGRA124_CLK_TSENSOR>,
+			<&tegra_car TEGRA124_CLK_SOC_THERM>;
+		clock-names = "tsensor", "soctherm";
+		resets = <&tegra_car 78>;
+		reset-names = "soctherm";
+
+		#thermal-sensor-cells = <1>;
+	};
+
+Example: referring to thermal sensors :
+
+       thermal-zones {
+                cpu {
+                        polling-delay-passive = <1000>;
+                        polling-delay = <1000>;
+
+                        thermal-sensors =
+                                <&soctherm TEGRA124_SOCTHERM_SENSOR_CPU>;
+                };
+	};

arch/arm/boot/dts/tegra124-jetson-tk1.dts

@@ -1942,4 +1942,48 @@
 			 <&tegra_car TEGRA124_CLK_EXTERN1>;
 		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
+
+	thermal-zones {
+		cpu {
+			trips {
+				trip@0 {
+					temperature = <101000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				/* There are currently no cooling maps because there are no cooling devices */
+			};
+		};
+
+		mem {
+			trips {
+				trip@0 {
+					temperature = <101000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				/* There are currently no cooling maps because there are no cooling devices */
+			};
+		};
+
+		gpu {
+			trips {
+				trip@0 {
+					temperature = <101000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				/* There are currently no cooling maps because there are no cooling devices */
+			};
+		};
+	};
 };

arch/arm/boot/dts/tegra124.dtsi

@@ -3,6 +3,7 @@
 #include <dt-bindings/pinctrl/pinctrl-tegra.h>
 #include <dt-bindings/pinctrl/pinctrl-tegra-xusb.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/thermal/tegra124-soctherm.h>
 
 #include "skeleton.dtsi"
 
@@ -640,6 +641,18 @@
 		status = "disabled";
 	};
 
+	soctherm: thermal-sensor@0,700e2000 {
+		compatible = "nvidia,tegra124-soctherm";
+		reg = <0x0 0x700e2000 0x0 0x1000>;
+		interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&tegra_car TEGRA124_CLK_TSENSOR>,
+			<&tegra_car TEGRA124_CLK_SOC_THERM>;
+		clock-names = "tsensor", "soctherm";
+		resets = <&tegra_car 78>;
+		reset-names = "soctherm";
+		#thermal-sensor-cells = <1>;
+	};
+
 	ahub@0,70300000 {
 		compatible = "nvidia,tegra124-ahub";
 		reg = <0x0 0x70300000 0x0 0x200>,
@@ -881,6 +894,40 @@
 		};
 	};
 
+	thermal-zones {
+		cpu {
+			polling-delay-passive = <1000>;
+			polling-delay = <1000>;
+
+			thermal-sensors =
+				<&soctherm TEGRA124_SOCTHERM_SENSOR_CPU>;
+		};
+
+		mem {
+			polling-delay-passive = <1000>;
+			polling-delay = <1000>;
+
+			thermal-sensors =
+				<&soctherm TEGRA124_SOCTHERM_SENSOR_MEM>;
+		};
+
+		gpu {
+			polling-delay-passive = <1000>;
+			polling-delay = <1000>;
+
+			thermal-sensors =
+				<&soctherm TEGRA124_SOCTHERM_SENSOR_GPU>;
+		};
+
+		pllx {
+			polling-delay-passive = <1000>;
+			polling-delay = <1000>;
+
+			thermal-sensors =
+				<&soctherm TEGRA124_SOCTHERM_SENSOR_PLLX>;
+		};
+	};
+
 	timer {
 		compatible = "arm,armv7-timer";
 		interrupts = <GIC_PPI 13

drivers/hwmon/lm75.c

@@ -176,6 +176,10 @@ static struct attribute *lm75_attrs[] = {
 };
 ATTRIBUTE_GROUPS(lm75);
 
+static const struct thermal_zone_of_device_ops lm75_of_thermal_ops = {
+	.get_temp = lm75_read_temp,
+};
+
 /*-----------------------------------------------------------------------*/
 
 /* device probe and removal */
@@ -291,10 +295,9 @@ lm75_probe(struct i2c_client *client, const struct i2c_device_id *id)
 	if (IS_ERR(data->hwmon_dev))
 		return PTR_ERR(data->hwmon_dev);
 
-	data->tz = thermal_zone_of_sensor_register(data->hwmon_dev,
-						   0,
+	data->tz = thermal_zone_of_sensor_register(data->hwmon_dev, 0,
 						   data->hwmon_dev,
-						   lm75_read_temp, NULL);
+						   &lm75_of_thermal_ops);
 	if (IS_ERR(data->tz))
 		data->tz = NULL;
 

drivers/hwmon/ntc_thermistor.c

@@ -486,6 +486,10 @@ static const struct attribute_group ntc_attr_group = {
 	.attrs = ntc_attributes,
 };
 
+static const struct thermal_zone_of_device_ops ntc_of_thermal_ops = {
+	.get_temp = ntc_read_temp,
+};
+
 static int ntc_thermistor_probe(struct platform_device *pdev)
 {
 	const struct of_device_id *of_id =
@@ -579,7 +583,7 @@ static int ntc_thermistor_probe(struct platform_device *pdev)
 								pdev_id->name);
 
 	data->tz = thermal_zone_of_sensor_register(data->dev, 0, data->dev,
-						ntc_read_temp, NULL);
+						   &ntc_of_thermal_ops);
 	if (IS_ERR(data->tz)) {
 		dev_dbg(&pdev->dev, "Failed to register to thermal fw.\n");
 		data->tz = NULL;

drivers/hwmon/tmp102.c

@@ -158,6 +158,10 @@ ATTRIBUTE_GROUPS(tmp102);
 #define TMP102_CONFIG  (TMP102_CONF_TM | TMP102_CONF_EM | TMP102_CONF_CR1)
 #define TMP102_CONFIG_RD_ONLY (TMP102_CONF_R0 | TMP102_CONF_R1 | TMP102_CONF_AL)
 
+static const struct thermal_zone_of_device_ops tmp102_of_thermal_ops = {
+	.get_temp = tmp102_read_temp,
+};
+
 static int tmp102_probe(struct i2c_client *client,
 				  const struct i2c_device_id *id)
 {
@@ -215,7 +219,7 @@ static int tmp102_probe(struct i2c_client *client,
 	}
 	tmp102->hwmon_dev = hwmon_dev;
 	tmp102->tz = thermal_zone_of_sensor_register(hwmon_dev, 0, hwmon_dev,
-						     tmp102_read_temp, NULL);
+						     &tmp102_of_thermal_ops);
 	if (IS_ERR(tmp102->tz))
 		tmp102->tz = NULL;
 

drivers/thermal/Kconfig

@@ -112,6 +112,18 @@ config CPU_THERMAL
 
 	  If you want this support, you should say Y here.
 
+config CLOCK_THERMAL
+	bool "Generic clock cooling support"
+	depends on COMMON_CLK
+	depends on PM_OPP
+	help
+	  This entry implements the generic clock cooling mechanism through
+	  frequency clipping. Typically used to cool off co-processors. The
+	  device that is configured to use this cooling mechanism will be
+	  controlled to reduce clock frequency whenever temperature is high.
+
+	  If you want this support, you should say Y here.
+
 config THERMAL_EMULATION
 	bool "Thermal emulation mode support"
 	help
@@ -143,6 +155,16 @@ config SPEAR_THERMAL
 	  Enable this to plug the SPEAr thermal sensor driver into the Linux
 	  thermal framework.
 
+config ROCKCHIP_THERMAL
+	tristate "Rockchip thermal driver"
+	depends on ARCH_ROCKCHIP
+	depends on RESET_CONTROLLER
+	help
+	  Rockchip thermal driver provides support for Temperature sensor
+	  ADC (TS-ADC) found on Rockchip SoCs. It supports one critical
+	  trip point. Cpufreq is used as the cooling device and will throttle
+	  CPUs when the Temperature crosses the passive trip point.
+
 config RCAR_THERMAL
 	tristate "Renesas R-Car thermal driver"
 	depends on ARCH_SHMOBILE || COMPILE_TEST
@@ -185,6 +207,16 @@ config ARMADA_THERMAL
 	  Enable this option if you want to have support for thermal management
 	  controller present in Armada 370 and Armada XP SoC.
 
+config TEGRA_SOCTHERM
+	tristate "Tegra SOCTHERM thermal management"
+	depends on ARCH_TEGRA
+	help
+	  Enable this option for integrated thermal management support on NVIDIA
+	  Tegra124 systems-on-chip. The driver supports four thermal zones
+	  (CPU, GPU, MEM, PLLX). Cooling devices can be bound to the thermal
+	  zones to manage temperatures. This option is also required for the
+	  emergency thermal reset (thermtrip) feature to function.
+
 config DB8500_CPUFREQ_COOLING
 	tristate "DB8500 cpufreq cooling"
 	depends on ARCH_U8500

drivers/thermal/Makefile

@@ -18,8 +18,12 @@ thermal_sys-$(CONFIG_THERMAL_GOV_USER_SPACE)	+= user_space.o
 # cpufreq cooling
 thermal_sys-$(CONFIG_CPU_THERMAL)	+= cpu_cooling.o
 
+# clock cooling
+thermal_sys-$(CONFIG_CLOCK_THERMAL)	+= clock_cooling.o
+
 # platform thermal drivers
 obj-$(CONFIG_SPEAR_THERMAL)	+= spear_thermal.o
+obj-$(CONFIG_ROCKCHIP_THERMAL)	+= rockchip_thermal.o
 obj-$(CONFIG_RCAR_THERMAL)	+= rcar_thermal.o
 obj-$(CONFIG_KIRKWOOD_THERMAL)  += kirkwood_thermal.o
 obj-y				+= samsung/
@@ -34,3 +38,4 @@ obj-$(CONFIG_INTEL_SOC_DTS_THERMAL)	+= intel_soc_dts_thermal.o
 obj-$(CONFIG_TI_SOC_THERMAL)	+= ti-soc-thermal/
 obj-$(CONFIG_INT340X_THERMAL)  += int340x_thermal/
 obj-$(CONFIG_ST_THERMAL)	+= st/
+obj-$(CONFIG_TEGRA_SOCTHERM)	+= tegra_soctherm.o