net/mlx4_en: Adding support of turning off link autonegotiation via e…

…thtool

This feature will allow the user to disable auto negotiation
on the port for mlx4 devices while setting the speed is limited
to 1GbE speeds.
Other speeds will not be accepted in autoneg off mode.

This functionality is permitted providing that the firmware
is compatible with this feature.
The above is determined by querying a new dedicated capability
bit in the device.

Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/mellanox/mlx4/en_ethtool.c

@@ -902,6 +902,7 @@ mlx4_en_set_link_ksettings(struct net_device *dev,
 	struct mlx4_en_priv *priv = netdev_priv(dev);
 	struct mlx4_ptys_reg ptys_reg;
 	__be32 proto_admin;
+	u8 cur_autoneg;
 	int ret;
 
 	u32 ptys_adv = ethtool2ptys_link_modes(
@@ -931,18 +932,31 @@ mlx4_en_set_link_ksettings(struct net_device *dev,
 		return 0;
 	}
 
-	proto_admin = link_ksettings->base.autoneg == AUTONEG_ENABLE ?
-		cpu_to_be32(ptys_adv) :
-		speed_set_ptys_admin(priv, speed,
-				     ptys_reg.eth_proto_cap);
+	cur_autoneg = ptys_reg.flags & MLX4_PTYS_AN_DISABLE_ADMIN ?
+				AUTONEG_DISABLE : AUTONEG_ENABLE;
+
+	if (link_ksettings->base.autoneg == AUTONEG_DISABLE) {
+		proto_admin = speed_set_ptys_admin(priv, speed,
+						   ptys_reg.eth_proto_cap);
+		if ((be32_to_cpu(proto_admin) &
+		     (MLX4_PROT_MASK(MLX4_1000BASE_CX_SGMII) |
+		      MLX4_PROT_MASK(MLX4_1000BASE_KX))) &&
+		    (ptys_reg.flags & MLX4_PTYS_AN_DISABLE_CAP))
+			ptys_reg.flags |= MLX4_PTYS_AN_DISABLE_ADMIN;
+	} else {
+		proto_admin = cpu_to_be32(ptys_adv);
+		ptys_reg.flags &= ~MLX4_PTYS_AN_DISABLE_ADMIN;
+	}
 
 	proto_admin &= ptys_reg.eth_proto_cap;
 	if (!proto_admin) {
 		en_warn(priv, "Not supported link mode(s) requested, check supported link modes.\n");
 		return -EINVAL; /* nothing to change due to bad input */
 	}
 
-	if (proto_admin == ptys_reg.eth_proto_admin)
+	if ((proto_admin == ptys_reg.eth_proto_admin) &&
+	    ((ptys_reg.flags & MLX4_PTYS_AN_DISABLE_CAP) &&
+	     (link_ksettings->base.autoneg == cur_autoneg)))
 		return 0; /* Nothing to change */
 
 	en_dbg(DRV, priv, "mlx4_ACCESS_PTYS_REG SET: ptys_reg.eth_proto_admin = 0x%x\n",

include/linux/mlx4/device.h

@@ -1539,8 +1539,13 @@ enum mlx4_ptys_proto {
 	MLX4_PTYS_EN = 1<<2,
 };
 
+enum mlx4_ptys_flags {
+	MLX4_PTYS_AN_DISABLE_CAP   = 1 << 5,
+	MLX4_PTYS_AN_DISABLE_ADMIN = 1 << 6,
+};
+
 struct mlx4_ptys_reg {
-	u8 resrvd1;
+	u8 flags;
 	u8 local_port;
 	u8 resrvd2;
 	u8 proto_mask;