ARM: davinci: remove unused board support

All Kconfig entries marked as "depends on UNUSED_BOARD_FILES"
and their direct dependencies are removed here as planned.

Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

arch/arm/Kconfig.debug

@@ -323,14 +323,6 @@ choice
 		  Say Y here if you want the debug print routines to direct
 		  their output to UART2 serial port on DaVinci DA8XX devices.
 
-	config DEBUG_DAVINCI_DMx_UART0
-		bool "Kernel low-level debugging on DaVinci DMx using UART0"
-		depends on ARCH_DAVINCI_DMx
-		select DEBUG_UART_8250
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to UART0 serial port on DaVinci DMx devices.
-
 	config DEBUG_DC21285_PORT
 		bool "Kernel low-level debugging messages via footbridge serial port"
 		depends on FOOTBRIDGE
@@ -1590,7 +1582,6 @@ config DEBUG_UART_8250
 
 config DEBUG_UART_PHYS
 	hex "Physical base address of debug UART"
-	default 0x01c20000 if DEBUG_DAVINCI_DMx_UART0
 	default 0x01c28000 if DEBUG_SUNXI_UART0
 	default 0x01c28400 if DEBUG_SUNXI_UART1
 	default 0x01d0c000 if DEBUG_DAVINCI_DA8XX_UART1
@@ -1810,7 +1801,6 @@ config DEBUG_UART_VIRT
 	default 0xfec03000 if DEBUG_SOCFPGA_CYCLONE5_UART1
 	default 0xfec12000 if DEBUG_MVEBU_UART0 || DEBUG_MVEBU_UART0_ALTERNATE
 	default 0xfec12100 if DEBUG_MVEBU_UART1_ALTERNATE
-	default 0xfec20000 if DEBUG_DAVINCI_DMx_UART0
 	default 0xfec90000 if DEBUG_RK32_UART2
 	default 0xfed0c000 if DEBUG_DAVINCI_DA8XX_UART1
 	default 0xfed0d000 if DEBUG_DAVINCI_DA8XX_UART2 || DEBUG_SD5203_UART
@@ -1854,9 +1844,9 @@ config DEBUG_UART_8250_WORD
 	default y if DEBUG_SOCFPGA_UART0 || DEBUG_SOCFPGA_ARRIA10_UART1 || \
 		DEBUG_SOCFPGA_CYCLONE5_UART1 || DEBUG_KEYSTONE_UART0 || \
 		DEBUG_KEYSTONE_UART1 || DEBUG_ALPINE_UART0 || \
-		DEBUG_DAVINCI_DMx_UART0 || DEBUG_DAVINCI_DA8XX_UART1 || \
-		DEBUG_DAVINCI_DA8XX_UART2 || DEBUG_BCM_IPROC_UART3 || \
-		DEBUG_BCM_KONA_UART || DEBUG_RK32_UART2
+		DEBUG_DAVINCI_DA8XX_UART1 || DEBUG_DAVINCI_DA8XX_UART2 || \
+		DEBUG_BCM_IPROC_UART3 || DEBUG_BCM_KONA_UART || \
+		DEBUG_RK32_UART2
 
 config DEBUG_UART_8250_PALMCHIP
 	bool "8250 UART is Palmchip BK-310x"

arch/arm/mach-davinci/Kconfig

@@ -14,20 +14,11 @@ menuconfig ARCH_DAVINCI
 
 if ARCH_DAVINCI
 
-config ARCH_DAVINCI_DMx
-	bool
-
 comment "DaVinci Core Type"
 
-config ARCH_DAVINCI_DM355
-	bool "DaVinci 355 based system"
-	depends on ATAGS && UNUSED_BOARD_FILES
-	select DAVINCI_AINTC
-	select ARCH_DAVINCI_DMx
-
 config ARCH_DAVINCI_DA830
 	bool "DA830/OMAP-L137/AM17x based system"
-	depends on !ARCH_DAVINCI_DMx || (AUTO_ZRELADDR && ARM_PATCH_PHYS_VIRT)
+	depends on AUTO_ZRELADDR && ARM_PATCH_PHYS_VIRT
 	depends on ATAGS
 	select ARCH_DAVINCI_DA8XX
 	# needed on silicon revs 1.0, 1.1:
@@ -36,20 +27,14 @@ config ARCH_DAVINCI_DA830
 
 config ARCH_DAVINCI_DA850
 	bool "DA850/OMAP-L138/AM18x based system"
-	depends on !ARCH_DAVINCI_DMx || (AUTO_ZRELADDR && ARM_PATCH_PHYS_VIRT)
+	depends on AUTO_ZRELADDR && ARM_PATCH_PHYS_VIRT
 	depends on ATAGS
 	select ARCH_DAVINCI_DA8XX
 	select DAVINCI_CP_INTC
 
 config ARCH_DAVINCI_DA8XX
 	bool
 
-config ARCH_DAVINCI_DM365
-	bool "DaVinci 365 based system"
-	depends on ATAGS && UNUSED_BOARD_FILES
-	select DAVINCI_AINTC
-	select ARCH_DAVINCI_DMx
-
 comment "DaVinci Board Type"
 
 config MACH_DA8XX_DT
@@ -61,117 +46,6 @@ config MACH_DA8XX_DT
 	  Say y here to include support for TI DaVinci DA850 based using
 	  Flattened Device Tree. More information at Documentation/devicetree
 
-config MACH_DAVINCI_DM355_EVM
-	bool "TI DM355 EVM"
-	default ARCH_DAVINCI_DM355
-	depends on ARCH_DAVINCI_DM355
-	help
-	  Configure this option to specify the whether the board used
-	  for development is a DM355 EVM
-
-config MACH_DM355_LEOPARD
-	bool "DM355 Leopard board"
-	depends on ARCH_DAVINCI_DM355
-	help
-	  Configure this option to specify the whether the board used
-	  for development is a DM355 Leopard board.
-
-config MACH_DAVINCI_DM365_EVM
-	bool "TI DM365 EVM"
-	default ARCH_DAVINCI_DM365
-	depends on ARCH_DAVINCI_DM365
-	help
-	  Configure this option to specify whether the board used
-	  for development is a DM365 EVM
-
-config MACH_DAVINCI_DA830_EVM
-	bool "TI DA830/OMAP-L137/AM17x Reference Platform"
-	default ARCH_DAVINCI_DA830
-	depends on ATAGS && UNUSED_BOARD_FILES
-	depends on ARCH_DAVINCI_DA830
-	select GPIO_PCF857X if I2C
-	help
-	  Say Y here to select the TI DA830/OMAP-L137/AM17x Evaluation Module.
-
-choice
-	prompt "Select DA830/OMAP-L137/AM17x UI board peripheral"
-	depends on MACH_DAVINCI_DA830_EVM
-	help
-	  The presence of UI card on the DA830/OMAP-L137/AM17x EVM is
-	  detected automatically based on successful probe of the I2C
-	  based GPIO expander on that board. This option selected in this
-	  menu has an effect only in case of a successful UI card detection.
-
-config DA830_UI_LCD
-	bool "LCD"
-	help
-	  Say Y here to use the LCD as a framebuffer or simple character
-	  display.
-
-config DA830_UI_NAND
-	bool "NAND flash"
-	help
-	  Say Y here to use the NAND flash. Do not forget to setup
-	  the switch correctly.
-endchoice
-
-config MACH_DAVINCI_DA850_EVM
-	bool "TI DA850/OMAP-L138/AM18x Reference Platform"
-	depends on ATAGS && UNUSED_BOARD_FILES
-	default ARCH_DAVINCI_DA850
-	depends on ARCH_DAVINCI_DA850
-	help
-	  Say Y here to select the TI DA850/OMAP-L138/AM18x Evaluation Module.
-
-choice
-	prompt "Select peripherals connected to expander on UI board"
-	depends on MACH_DAVINCI_DA850_EVM
-	help
-	  The presence of User Interface (UI) card on the DA850/OMAP-L138/AM18x
-	  EVM is detected automatically based on successful probe of the I2C
-	  based GPIO expander on that card. This option selected in this
-	  menu has an effect only in case of a successful UI card detection.
-
-config DA850_UI_NONE
-	bool "No peripheral is enabled"
-	help
-	  Say Y if you do not want to enable any of the peripherals connected
-	  to TCA6416 expander on DA850/OMAP-L138/AM18x EVM UI card
-
-config DA850_UI_RMII
-	bool "RMII Ethernet PHY"
-	help
-	  Say Y if you want to use the RMII PHY on the DA850/OMAP-L138/AM18x
-	  EVM. This PHY is found on the UI daughter card that is supplied with
-	  the EVM.
-	  NOTE: Please take care while choosing this option, MII PHY will
-	  not be functional if RMII mode is selected.
-
-config DA850_UI_SD_VIDEO_PORT
-	bool "Video Port Interface"
-	help
-	  Say Y if you want to use Video Port Interface (VPIF) on the
-	  DA850/OMAP-L138 EVM. The Video decoders/encoders are found on the
-	  UI daughter card that is supplied with the EVM.
-
-endchoice
-
-config MACH_MITYOMAPL138
-	bool "Critical Link MityDSP-L138/MityARM-1808 SoM"
-	depends on ARCH_DAVINCI_DA850
-	depends on ATAGS && UNUSED_BOARD_FILES
-	help
-	  Say Y here to select the Critical Link MityDSP-L138/MityARM-1808
-	  System on Module.  Information on this SoM may be found at
-	  https://www.mitydsp.com
-
-config MACH_OMAPL138_HAWKBOARD
-	bool "TI AM1808 / OMAPL-138 Hawkboard platform"
-	depends on ARCH_DAVINCI_DA850
-	depends on ATAGS && UNUSED_BOARD_FILES
-	help
-	  Say Y here to select the TI AM1808 / OMAPL-138 Hawkboard platform .
-
 config DAVINCI_MUX
 	bool "DAVINCI multiplexing support"
 	depends on ARCH_DAVINCI

arch/arm/mach-davinci/Makefile

@@ -10,20 +10,11 @@ obj-y 					:= serial.o usb.o common.o sram.o
 obj-$(CONFIG_DAVINCI_MUX)		+= mux.o
 
 # Chip specific
-obj-$(CONFIG_ARCH_DAVINCI_DM355)        += dm355.o devices.o
-obj-$(CONFIG_ARCH_DAVINCI_DM365)	+= dm365.o devices.o
 obj-$(CONFIG_ARCH_DAVINCI_DA830)	+= da830.o devices-da8xx.o usb-da8xx.o
 obj-$(CONFIG_ARCH_DAVINCI_DA850)	+= da850.o devices-da8xx.o usb-da8xx.o
 
 # Board specific
 obj-$(CONFIG_MACH_DA8XX_DT)		+= da8xx-dt.o pdata-quirks.o
-obj-$(CONFIG_MACH_DAVINCI_DM355_EVM)	+= board-dm355-evm.o
-obj-$(CONFIG_MACH_DM355_LEOPARD)	+= board-dm355-leopard.o
-obj-$(CONFIG_MACH_DAVINCI_DM365_EVM)	+= board-dm365-evm.o
-obj-$(CONFIG_MACH_DAVINCI_DA830_EVM)	+= board-da830-evm.o
-obj-$(CONFIG_MACH_DAVINCI_DA850_EVM)	+= board-da850-evm.o
-obj-$(CONFIG_MACH_MITYOMAPL138)		+= board-mityomapl138.o
-obj-$(CONFIG_MACH_OMAPL138_HAWKBOARD)	+= board-omapl138-hawk.o
 
 # Power Management
 obj-$(CONFIG_CPU_IDLE)			+= cpuidle.o