Merge tag 'pinctrl-fixes-v3.10-2' of git://git.kernel.org/pub/scm/lin…

…ux/kernel/git/linusw/linux-pinctrl

Pull pinctrl fixes from Linus Walleij:

 - Three fixes to make the boot path for device tree work properly on
   the Nomadik pin controller.

 - Compile warning fix for the vt8500 driver.

 - Fix error path in pinctrl-single.

 - Free mappings in error path of the Lantiq controller.

 - Documentation fixes.

* tag 'pinctrl-fixes-v3.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl/lantiq: Free mapping configs for both pin and groups
  pinctrl: single: fix error return code in pcs_parse_one_pinctrl_entry()
  pinctrl: generic: Fix typos and clarify comments
  pinctrl: vt8500: Fix incorrect data in WM8750 pinctrl table
  pinctrl: abx500: Rejiggle platform data and DT initialisation
  pinctrl: abx500: Specify failed sub-driver by ID instead of driver_data

drivers/pinctrl/pinctrl-abx500.c

@@ -851,23 +851,12 @@ static int abx500_gpio_probe(struct platform_device *pdev)
 
 	if (abx500_pdata)
 		pdata = abx500_pdata->gpio;
-	if (!pdata) {
-		if (np) {
-			const struct of_device_id *match;
 
-			match = of_match_device(abx500_gpio_match, &pdev->dev);
-			if (!match)
-				return -ENODEV;
-			id = (unsigned long)match->data;
-		} else {
-			dev_err(&pdev->dev, "gpio dt and platform data missing\n");
-			return -ENODEV;
-		}
+	if (!(pdata || np)) {
+		dev_err(&pdev->dev, "gpio dt and platform data missing\n");
+		return -ENODEV;
 	}
 
-	if (platid)
-		id = platid->driver_data;
-
 	pct = devm_kzalloc(&pdev->dev, sizeof(struct abx500_pinctrl),
 				   GFP_KERNEL);
 	if (pct == NULL) {
@@ -882,6 +871,16 @@ static int abx500_gpio_probe(struct platform_device *pdev)
 	pct->chip.dev = &pdev->dev;
 	pct->chip.base = (np) ? -1 : pdata->gpio_base;
 
+	if (platid)
+		id = platid->driver_data;
+	else if (np) {
+		const struct of_device_id *match;
+
+		match = of_match_device(abx500_gpio_match, &pdev->dev);
+		if (match)
+			id = (unsigned long)match->data;
+	}
+
 	/* initialize the lock */
 	mutex_init(&pct->lock);
 
@@ -900,8 +899,7 @@ static int abx500_gpio_probe(struct platform_device *pdev)
 		abx500_pinctrl_ab8505_init(&pct->soc);
 		break;
 	default:
-		dev_err(&pdev->dev, "Unsupported pinctrl sub driver (%d)\n",
-				(int) platid->driver_data);
+		dev_err(&pdev->dev, "Unsupported pinctrl sub driver (%d)\n", id);
 		mutex_destroy(&pct->lock);
 		return -EINVAL;
 	}

drivers/pinctrl/pinctrl-lantiq.c

@@ -52,7 +52,8 @@ static void ltq_pinctrl_dt_free_map(struct pinctrl_dev *pctldev,
 	int i;
 
 	for (i = 0; i < num_maps; i++)
-		if (map[i].type == PIN_MAP_TYPE_CONFIGS_PIN)
+		if (map[i].type == PIN_MAP_TYPE_CONFIGS_PIN ||
+		    map[i].type == PIN_MAP_TYPE_CONFIGS_GROUP)
 			kfree(map[i].data.configs.configs);
 	kfree(map);
 }

drivers/pinctrl/pinctrl-single.c

@@ -1166,7 +1166,8 @@ static int pcs_parse_one_pinctrl_entry(struct pcs_device *pcs,
 	(*map)->data.mux.function = np->name;
 
 	if (pcs->is_pinconf) {
-		if (pcs_parse_pinconf(pcs, np, function, map))
+		res = pcs_parse_pinconf(pcs, np, function, map);
+		if (res)
 			goto free_pingroups;
 		*num_maps = 2;
 	} else {

drivers/pinctrl/vt8500/pinctrl-wm8750.c

@@ -53,7 +53,7 @@ static const struct wmt_pinctrl_bank_registers wm8750_banks[] = {
 #define WMT_PIN_EXTGPIO6	WMT_PIN(0, 6)
 #define WMT_PIN_EXTGPIO7	WMT_PIN(0, 7)
 #define WMT_PIN_WAKEUP0		WMT_PIN(0, 16)
-#define WMT_PIN_WAKEUP1		WMT_PIN(0, 16)
+#define WMT_PIN_WAKEUP1		WMT_PIN(0, 17)
 #define WMT_PIN_SD0CD		WMT_PIN(0, 28)
 #define WMT_PIN_VDOUT0		WMT_PIN(1, 0)
 #define WMT_PIN_VDOUT1		WMT_PIN(1, 1)

include/linux/pinctrl/pinconf-generic.h

@@ -37,17 +37,17 @@
  *	if it is 0, pull-down is disabled.
  * @PIN_CONFIG_DRIVE_PUSH_PULL: the pin will be driven actively high and
  *	low, this is the most typical case and is typically achieved with two
- *	active transistors on the output. Sending this config will enabale
+ *	active transistors on the output. Setting this config will enable
  *	push-pull mode, the argument is ignored.
  * @PIN_CONFIG_DRIVE_OPEN_DRAIN: the pin will be driven with open drain (open
  *	collector) which means it is usually wired with other output ports
- *	which are then pulled up with an external resistor. Sending this
- *	config will enabale open drain mode, the argument is ignored.
+ *	which are then pulled up with an external resistor. Setting this
+ *	config will enable open drain mode, the argument is ignored.
  * @PIN_CONFIG_DRIVE_OPEN_SOURCE: the pin will be driven with open source
- *	(open emitter). Sending this config will enabale open drain mode, the
+ *	(open emitter). Setting this config will enable open drain mode, the
  *	argument is ignored.
- * @PIN_CONFIG_DRIVE_STRENGTH: the pin will output the current passed as
- * 	argument. The argument is in mA.
+ * @PIN_CONFIG_DRIVE_STRENGTH: the pin will sink or source at most the current
+ *	passed as argument. The argument is in mA.
  * @PIN_CONFIG_INPUT_SCHMITT_ENABLE: control schmitt-trigger mode on the pin.
  *      If the argument != 0, schmitt-trigger mode is enabled. If it's 0,
  *      schmitt-trigger mode is disabled.