Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel…

…/git/soc/soc

Pull ARM SoC fixes from Olof Johansson:
 "A set of fixes that we've merged late, but for the most part that have
  been sitting in -next for a while through platform maintainer trees:

   - Fixes to suspend/resume on Tegra, caused by the added features this
     merge window

   - Cleanups and minor fixes to TI additions this merge window

   - Tee fixes queued up late before the merge window, included here.

   - A handful of other fixlets

  There's also a refresh of the shareed config files (multi_v* on
  32-bit, and defconfig on 64-bit), to avoid conflicts when we get new
  contributions"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
  ARM: multi_v7_defconfig: Restore debugfs support
  ARM: defconfig: re-run savedefconfig on multi_v* configs
  arm64: defconfig: re-run savedefconfig
  ARM: pxa: Fix resource properties
  soc: mediatek: cmdq: fixup wrong input order of write api
  soc: aspeed: Fix snoop_file_poll()'s return type
  MAINTAINERS: Switch to Marvell addresses
  MAINTAINERS: update Cavium ThunderX drivers
  Revert "arm64: dts: juno: add dma-ranges property"
  MAINTAINERS: Make Nicolas Saenz Julienne the new bcm2835 maintainer
  firmware: arm_scmi: Avoid double free in error flow
  arm64: dts: juno: Fix UART frequency
  ARM: dts: Fix sgx sysconfig register for omap4
  arm: socfpga: execute cold reboot by default
  ARM: dts: Fix vcsi regulator to be always-on for droid4 to prevent hangs
  ARM: dts: dra7: fix cpsw mdio fck clock
  ARM: dts: am57xx-beagle-x15: Update pinmux name to ddr_3_3v
  ARM: dts: omap3-tao3530: Fix incorrect MMC card detection GPIO polarity
  soc/tegra: pmc: Add reset sources and levels on Tegra194
  soc/tegra: pmc: Add missing IRQ callbacks on Tegra194
  ...

.mailmap

@@ -105,6 +105,9 @@ James E Wilson <wilson@specifix.com>
 James Hogan <jhogan@kernel.org> <james.hogan@imgtec.com>
 James Hogan <jhogan@kernel.org> <james@albanarts.com>
 James Ketrenos <jketreno@io.(none)>
+Jan Glauber <jan.glauber@gmail.com> <jang@de.ibm.com>
+Jan Glauber <jan.glauber@gmail.com> <jang@linux.vnet.ibm.com>
+Jan Glauber <jan.glauber@gmail.com> <jglauber@cavium.com>
 Jason Gunthorpe <jgg@ziepe.ca> <jgg@mellanox.com>
 Jason Gunthorpe <jgg@ziepe.ca> <jgunthorpe@obsidianresearch.com>
 Javi Merino <javi.merino@kernel.org> <javi.merino@arm.com>

MAINTAINERS

@@ -1584,8 +1584,8 @@ S:	Maintained
 F:	arch/arm/mach-cns3xxx/
 
 ARM/CAVIUM THUNDER NETWORK DRIVER
-M:	Sunil Goutham <sgoutham@cavium.com>
-M:	Robert Richter <rric@kernel.org>
+M:	Sunil Goutham <sgoutham@marvell.com>
+M:	Robert Richter <rrichter@marvell.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Supported
 F:	drivers/net/ethernet/cavium/thunder/
@@ -3228,8 +3228,7 @@ N:	kona
 F:	arch/arm/mach-bcm/
 
 BROADCOM BCM2711/BCM2835 ARM ARCHITECTURE
-M:	Eric Anholt <eric@anholt.net>
-M:	Stefan Wahren <wahrenst@gmx.net>
+M:	Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
 L:	bcm-kernel-feedback-list@broadcom.com
 L:	linux-rpi-kernel@lists.infradead.org (moderated for non-subscribers)
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -3742,9 +3741,8 @@ S:	Maintained
 F:	drivers/net/wireless/ath/carl9170/
 
 CAVIUM I2C DRIVER
-M:	Jan Glauber <jglauber@cavium.com>
-M:	David Daney <david.daney@cavium.com>
-W:	http://www.cavium.com
+M:	Robert Richter <rrichter@marvell.com>
+W:	http://www.marvell.com
 S:	Supported
 F:	drivers/i2c/busses/i2c-octeon*
 F:	drivers/i2c/busses/i2c-thunderx*
@@ -3754,27 +3752,25 @@ M:	Derek Chickles <dchickles@marvell.com>
 M:	Satanand Burla <sburla@marvell.com>
 M:	Felix Manlunas <fmanlunas@marvell.com>
 L:	netdev@vger.kernel.org
-W:	http://www.cavium.com
+W:	http://www.marvell.com
 S:	Supported
 F:	drivers/net/ethernet/cavium/liquidio/
 
 CAVIUM MMC DRIVER
-M:	Jan Glauber <jglauber@cavium.com>
-M:	David Daney <david.daney@cavium.com>
-M:	Steven J. Hill <Steven.Hill@cavium.com>
-W:	http://www.cavium.com
+M:	Robert Richter <rrichter@marvell.com>
+W:	http://www.marvell.com
 S:	Supported
 F:	drivers/mmc/host/cavium*
 
 CAVIUM OCTEON-TX CRYPTO DRIVER
-M:	George Cherian <george.cherian@cavium.com>
+M:	George Cherian <gcherian@marvell.com>
 L:	linux-crypto@vger.kernel.org
-W:	http://www.cavium.com
+W:	http://www.marvell.com
 S:	Supported
 F:	drivers/crypto/cavium/cpt/
 
 CAVIUM THUNDERX2 ARM64 SOC
-M:	Robert Richter <rrichter@cavium.com>
+M:	Robert Richter <rrichter@marvell.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	arch/arm64/boot/dts/cavium/thunder2-99xx*
@@ -5892,15 +5888,14 @@ F:	drivers/edac/highbank*
 
 EDAC-CAVIUM OCTEON
 M:	Ralf Baechle <ralf@linux-mips.org>
-M:	David Daney <david.daney@cavium.com>
+M:	Robert Richter <rrichter@marvell.com>
 L:	linux-edac@vger.kernel.org
 L:	linux-mips@vger.kernel.org
 S:	Supported
 F:	drivers/edac/octeon_edac*
 
 EDAC-CAVIUM THUNDERX
-M:	David Daney <david.daney@cavium.com>
-M:	Jan Glauber <jglauber@cavium.com>
+M:	Robert Richter <rrichter@marvell.com>
 L:	linux-edac@vger.kernel.org
 S:	Supported
 F:	drivers/edac/thunderx_edac*
@@ -12799,7 +12794,7 @@ F:	Documentation/devicetree/bindings/pci/axis,artpec*
 F:	drivers/pci/controller/dwc/*artpec*
 
 PCIE DRIVER FOR CAVIUM THUNDERX
-M:	David Daney <david.daney@cavium.com>
+M:	Robert Richter <rrichter@marvell.com>
 L:	linux-pci@vger.kernel.org
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Supported
@@ -16372,7 +16367,7 @@ S:	Maintained
 F:	drivers/net/thunderbolt.c
 
 THUNDERX GPIO DRIVER
-M:	David Daney <david.daney@cavium.com>
+M:	Robert Richter <rrichter@marvell.com>
 S:	Maintained
 F:	drivers/gpio/gpio-thunderx.c
 
@@ -18177,10 +18172,9 @@ S:	Supported
 F:	drivers/char/xillybus/
 
 XLP9XX I2C DRIVER
-M:	George Cherian <george.cherian@cavium.com>
-M:	Jan Glauber <jglauber@cavium.com>
+M:	George Cherian <gcherian@marvell.com>
 L:	linux-i2c@vger.kernel.org
-W:	http://www.cavium.com
+W:	http://www.marvell.com
 S:	Supported
 F:	Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt
 F:	drivers/i2c/busses/i2c-xlp9xx.c

arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts

@@ -24,7 +24,7 @@
 };
 
 &mmc2 {
-	pinctrl-names = "default", "hs", "ddr_1_8v";
+	pinctrl-names = "default", "hs", "ddr_3_3v";
 	pinctrl-0 = <&mmc2_pins_default>;
 	pinctrl-1 = <&mmc2_pins_hs>;
 	pinctrl-2 = <&mmc2_pins_ddr_3_3v_rev11 &mmc2_iodelay_ddr_3_3v_rev11_conf>;

arch/arm/boot/dts/am57xx-beagle-x15-revc.dts

@@ -24,7 +24,7 @@
 };
 
 &mmc2 {
-	pinctrl-names = "default", "hs", "ddr_1_8v";
+	pinctrl-names = "default", "hs", "ddr_3_3v";
 	pinctrl-0 = <&mmc2_pins_default>;
 	pinctrl-1 = <&mmc2_pins_hs>;
 	pinctrl-2 = <&mmc2_pins_ddr_rev20>;

arch/arm/boot/dts/bcm2711-rpi-4-b.dts

@@ -19,6 +19,10 @@
 		reg = <0 0 0>;
 	};
 
+	aliases {
+		ethernet0 = &genet;
+	};
+
 	leds {
 		act {
 			gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
@@ -97,6 +101,19 @@
 	status = "okay";
 };
 
+&genet {
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-rxid";
+	status = "okay";
+};
+
+&genet_mdio {
+	phy1: ethernet-phy@1 {
+		/* No PHY interrupt */
+		reg = <0x1>;
+	};
+};
+
 /* uart0 communicates with the BT module */
 &uart0 {
 	pinctrl-names = "default";

arch/arm/boot/dts/bcm2711.dtsi

@@ -12,6 +12,26 @@
 
 	interrupt-parent = <&gicv2>;
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges;
+
+		/*
+		 * arm64 reserves the CMA by default somewhere in ZONE_DMA32,
+		 * that's not good enough for the BCM2711 as some devices can
+		 * only address the lower 1G of memory (ZONE_DMA).
+		 */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			size = <0x2000000>; /* 32MB */
+			alloc-ranges = <0x0 0x00000000 0x40000000>;
+			reusable;
+			linux,cma-default;
+		};
+	};
+
+
 	soc {
 		/*
 		 * Defined ranges:
@@ -305,6 +325,32 @@
 			cpu-release-addr = <0x0 0x000000f0>;
 		};
 	};
+
+	scb {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+
+		ranges = <0x0 0x7c000000  0x0 0xfc000000  0x03800000>;
+
+		genet: ethernet@7d580000 {
+			compatible = "brcm,bcm2711-genet-v5";
+			reg = <0x0 0x7d580000 0x10000>;
+			#address-cells = <0x1>;
+			#size-cells = <0x1>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+
+			genet_mdio: mdio@e14 {
+				compatible = "brcm,genet-mdio-v5";
+				reg = <0xe14 0x8>;
+				reg-names = "mdio";
+				#address-cells = <0x0>;
+				#size-cells = <0x1>;
+			};
+		};
+	};
 };
 
 &clk_osc {

arch/arm/boot/dts/dra7-l4.dtsi

@@ -3056,7 +3056,7 @@
 
 				davinci_mdio: mdio@1000 {
 					compatible = "ti,cpsw-mdio","ti,davinci_mdio";
-					clocks = <&gmac_clkctrl DRA7_GMAC_GMAC_CLKCTRL 0>;
+					clocks = <&gmac_main_clk>;
 					clock-names = "fck";
 					#address-cells = <1>;
 					#size-cells = <0>;

arch/arm/boot/dts/logicpd-torpedo-37xx-devkit-28.dts

@@ -11,6 +11,5 @@
 #include "logicpd-torpedo-37xx-devkit.dts"
 
 &lcd0 {
-	/* To make it work, set CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=4 */
 	compatible = "logicpd,type28";
 };

arch/arm/boot/dts/logicpd-torpedo-baseboard.dtsi

@@ -101,6 +101,12 @@
 	};
 };
 
+&hdqw1w {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdq_pins>;
+};
+
+
 &vpll2 {
 	regulator-always-on;
 };
@@ -126,7 +132,6 @@
 
 	lcd0: display {
 		/* This isn't the exact LCD, but the timings meet spec */
-		/* To make it work, set CONFIG_OMAP2_DSS_MIN_FCK_PER_PCK=4 */
 		compatible = "newhaven,nhd-4.3-480272ef-atxl";
 		label = "15";
 		pinctrl-names = "default";
@@ -169,6 +174,12 @@
 		>;
 	};
 
+	hdq_pins: hdq_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21c6, PIN_INPUT_PULLUP | MUX_MODE0) /* hdq_sio */
+		>;
+	};
+
 	pwm_pins: pinmux_pwm_pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3)       /* gpmc_ncs5.gpt_10_pwm_evt */

arch/arm/boot/dts/motorola-cpcap-mapphone.dtsi

@@ -162,12 +162,12 @@
 		regulator-enable-ramp-delay = <1000>;
 	};
 
-	/* Used by DSS */
+	/* Used by DSS and is the "zerov_regulator" trigger for SoC off mode */
 	vcsi: VCSI {
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
 		regulator-enable-ramp-delay = <1000>;
-		regulator-boot-on;
+		regulator-always-on;
 	};
 
 	vdac: VDAC {

arch/arm/boot/dts/omap3-tao3530.dtsi

@@ -222,7 +222,7 @@
 	pinctrl-0 = <&mmc1_pins>;
 	vmmc-supply = <&vmmc1>;
 	vqmmc-supply = <&vsim>;
-	cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_LOW>;
 	bus-width = <8>;
 };
 

arch/arm/boot/dts/omap4.dtsi

@@ -330,8 +330,8 @@
 
 		target-module@56000000 {
 			compatible = "ti,sysc-omap4", "ti,sysc";
-			reg = <0x5601fc00 0x4>,
-			      <0x5601fc10 0x4>;
+			reg = <0x5600fe00 0x4>,
+			      <0x5600fe10 0x4>;
 			reg-names = "rev", "sysc";
 			ti,sysc-midle = <SYSC_IDLE_FORCE>,
 					<SYSC_IDLE_NO>,

arch/arm/configs/multi_v4t_defconfig

@@ -4,22 +4,19 @@ CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EMBEDDED=y
 CONFIG_SLOB=y
-CONFIG_JUMP_LABEL=y
-CONFIG_PARTITION_ADVANCED=y
-# CONFIG_IOSCHED_CFQ is not set
 CONFIG_ARCH_MULTI_V4T=y
 # CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_AT91=y
 CONFIG_SOC_AT91RM9200=y
 CONFIG_ARCH_CLPS711X=y
+CONFIG_ARCH_MXC=y
+CONFIG_SOC_IMX1=y
 CONFIG_ARCH_INTEGRATOR=y
 CONFIG_ARCH_INTEGRATOR_AP=y
 CONFIG_INTEGRATOR_IMPD1=y
 CONFIG_INTEGRATOR_CM720T=y
 CONFIG_INTEGRATOR_CM920T=y
 CONFIG_INTEGRATOR_CM922T_XA10=y
-CONFIG_ARCH_MXC=y
-CONFIG_SOC_IMX1=y
 CONFIG_ARCH_NSPIRE=y
 CONFIG_AEABI=y
 # CONFIG_ATAGS is not set
@@ -28,6 +25,8 @@ CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_CPU_IDLE=y
 CONFIG_ARM_CPUIDLE=y
 CONFIG_ARM_CLPS711X_CPUIDLE=y
+CONFIG_JUMP_LABEL=y
+CONFIG_PARTITION_ADVANCED=y
 # CONFIG_COREDUMP is not set
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
@@ -81,7 +80,6 @@ CONFIG_FB=y
 CONFIG_FB_CLPS711X=y
 CONFIG_FB_IMX=y
 CONFIG_LCD_PLATFORM=y
-CONFIG_BACKLIGHT_PWM=y
 # CONFIG_USB_SUPPORT is not set
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
@@ -92,12 +90,11 @@ CONFIG_LEDS_TRIGGER_HEARTBEAT=y
 CONFIG_PWM=y
 CONFIG_PWM_ATMEL=y
 CONFIG_PWM_CLPS711X=y
-CONFIG_PWM_IMX=y
 CONFIG_EXT2_FS=y
 CONFIG_MSDOS_FS=y
 CONFIG_VFAT_FS=y
 CONFIG_CRAMFS=y
 CONFIG_MINIX_FS=y
+CONFIG_CRC_CCITT=y
 # CONFIG_FTRACE is not set
 CONFIG_DEBUG_USER=y
-CONFIG_CRC_CCITT=y