Merge branches 'ntrig', 'picolcd', 'prodikeys' and 'roccat-kone' into…

… for-linus

Conflicts:
	drivers/hid/Makefile

Documentation/ABI/testing/sysfs-driver-hid-picolcd

@@ -0,0 +1,43 @@
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/operation_mode
+Date:		March 2010
+Contact:	Bruno Prémont <bonbons@linux-vserver.org>
+Description:	Make it possible to switch the PicoLCD device between LCD
+		(firmware) and bootloader (flasher) operation modes.
+
+		Reading: returns list of available modes, the active mode being
+		enclosed in brackets ('[' and ']')
+
+		Writing: causes operation mode switch. Permitted values are
+		the non-active mode names listed when read.
+
+		Note: when switching mode the current PicoLCD HID device gets
+		disconnected and reconnects after above delay (see attribute
+		operation_mode_delay for its value).
+
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/operation_mode_delay
+Date:		April 2010
+Contact:	Bruno Prémont <bonbons@linux-vserver.org>
+Description:	Delay PicoLCD waits before restarting in new mode when
+		operation_mode has changed.
+
+		Reading/Writing: It is expressed in ms and permitted range is
+		0..30000ms.
+
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/fb_update_rate
+Date:		March 2010
+Contact:	Bruno Prémont <bonbons@linux-vserver.org>
+Description:	Make it possible to adjust defio refresh rate.
+
+		Reading: returns list of available refresh rates (expressed in Hz),
+		the active refresh rate being enclosed in brackets ('[' and ']')
+
+		Writing: accepts new refresh rate expressed in integer Hz
+		within permitted rates.
+
+		Note: As device can barely do 2 complete refreshes a second
+		it only makes sense to adjust this value if only one or two
+		tiles get changed and it's not appropriate to expect the application
+		to flush it's tiny changes explicitely at higher than default rate.
+

Documentation/ABI/testing/sysfs-driver-hid-prodikeys

@@ -0,0 +1,29 @@
+What:		/sys/bus/hid/drivers/prodikeys/.../channel
+Date:		April 2010
+KernelVersion:	2.6.34
+Contact:	Don Prince <dhprince.devel@yahoo.co.uk>
+Description:
+		Allows control (via software) the midi channel to which
+		that the pc-midi keyboard will output.midi data.
+		Range: 0..15
+		Type:  Read/write
+What:		/sys/bus/hid/drivers/prodikeys/.../sustain
+Date:		April 2010
+KernelVersion:	2.6.34
+Contact:	Don Prince <dhprince.devel@yahoo.co.uk>
+Description:
+		Allows control (via software) the sustain duration of a
+		note held by the pc-midi driver.
+		0 means sustain mode is disabled.
+		Range: 0..5000 (milliseconds)
+		Type:  Read/write
+What:		/sys/bus/hid/drivers/prodikeys/.../octave
+Date:		April 2010
+KernelVersion:	2.6.34
+Contact:	Don Prince <dhprince.devel@yahoo.co.uk>
+Description:
+		Controls the octave shift modifier in the pc-midi driver.
+		The octave can be shifted via software up/down 2 octaves.
+		0 means the no ocatve shift.
+		Range: -2..2 (minus 2 to plus 2)
+		Type: Read/Write

Documentation/ABI/testing/sysfs-driver-hid-roccat-kone

@@ -0,0 +1,111 @@
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/actual_dpi
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	It is possible to switch the dpi setting of the mouse with the
+		press of a button.
+		When read, this file returns the raw number of the actual dpi
+		setting reported by the mouse. This number has to be further
+		processed to receive the real dpi value.
+
+		VALUE DPI
+		1     800
+		2     1200
+		3     1600
+		4     2000
+		5     2400
+		6     3200
+
+		This file is readonly.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/actual_profile
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	When read, this file returns the number of the actual profile.
+		This file is readonly.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/firmware_version
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	When read, this file returns the raw integer version number of the
+		firmware reported by the mouse. Using the integer value eases
+		further usage in other programs. To receive the real version
+		number the decimal point has to be shifted 2 positions to the
+		left. E.g. a returned value of 138 means 1.38
+		This file is readonly.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/kone_driver_version
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	When read, this file returns the driver version.
+		The format of the string is "v<major>.<minor>.<patchlevel>".
+		This attribute is used by the userland tools to find the sysfs-
+		paths of installed kone-mice and determine the capabilites of
+		the driver. Versions of this driver for old kernels replace
+		usbhid instead of generic-usb. The way to scan for this file
+		has been chosen to provide a consistent way for all supported
+		kernel versions.
+		This file is readonly.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/profile[1-5]
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	The mouse can store 5 profiles which can be switched by the
+                press of a button. A profile holds informations like button
+                mappings, sensitivity, the colors of the 5 leds and light
+                effects.
+                When read, these files return the respective profile. The
+                returned data is 975 bytes in size.
+		When written, this file lets one write the respective profile
+		data back to the mouse. The data has to be 975 bytes long.
+		The mouse will reject invalid data, whereas the profile number
+		stored in the profile doesn't need to fit the number of the
+		store.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/settings
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	When read, this file returns the settings stored in the mouse.
+		The size of the data is 36 bytes and holds information like the
+		startup_profile, tcu state and calibration_data.
+		When written, this file lets write settings back to the mouse.
+		The data has to be 36 bytes long. The mouse will reject invalid
+		data.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/startup_profile
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	The integer value of this attribute ranges from 1 to 5.
+                When read, this attribute returns the number of the profile
+                that's active when the mouse is powered on.
+		When written, this file sets the number of the startup profile
+		and the mouse activates this profile immediately.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/tcu
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	The mouse has a "Tracking Control Unit" which lets the user
+		calibrate the laser power to fit the mousepad surface.
+		When read, this file returns the current state of the TCU,
+		where 0 means off and 1 means on.
+		Writing 0 in this file will switch the TCU off.
+		Writing 1 in this file will start the calibration which takes
+		around 6 seconds to complete and activates the TCU.
+
+What:		/sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/weight
+Date:		March 2010
+Contact:	Stefan Achatz <erazor_de@users.sourceforge.net>
+Description:	The mouse can be equipped with one of four supplied weights
+		ranging from 5 to 20 grams which are recognized by the mouse
+		and its value can be read out. When read, this file returns the
+		raw value returned by the mouse which eases further processing
+		in other software.
+		The values map to the weights as follows:
+
+		VALUE WEIGHT
+		0     none
+		1     5g
+		2     10g
+		3     15g
+		4     20g
+
+		This file is readonly.

drivers/hid/Kconfig

@@ -106,6 +106,21 @@ config HID_CHICONY
 	---help---
 	Support for Chicony Tactical pad.
 
+config HID_PRODIKEYS
+	tristate "Prodikeys PC-MIDI Keyboard support"
+	depends on USB_HID && SND
+	select SND_RAWMIDI
+	---help---
+	Support for Prodikeys PC-MIDI Keyboard device support.
+	Say Y here to enable support for this device.
+	- Prodikeys PC-MIDI keyboard.
+	  The Prodikeys PC-MIDI acts as a USB Audio device, with one MIDI
+	  input and one MIDI output. These MIDI jacks appear as
+	  a sound "card" in the ALSA sound system.
+	  Note: if you say N here, this device will still function as a basic
+	  multimedia keyboard, but will lack support for the musical keyboard
+	  and some additional multimedia keys.
+
 config HID_CYPRESS
 	tristate "Cypress" if EMBEDDED
 	depends on USB_HID
@@ -274,12 +289,76 @@ config HID_PETALYNX
 	---help---
 	Support for Petalynx Maxter remote control.
 
+config HID_PICOLCD
+	tristate "PicoLCD (graphic version)"
+	depends on USB_HID
+	---help---
+	  This provides support for Minibox PicoLCD devices, currently
+	  only the graphical ones are supported.
+
+	  This includes support for the following device features:
+	  - Keypad
+	  - Switching between Firmware and Flash mode
+	  - EEProm / Flash access     (via debugfs)
+	  Features selectively enabled:
+	  - Framebuffer for monochrome 256x64 display
+	  - Backlight control
+	  - Contrast control
+	  - General purpose outputs
+	  Features that are not (yet) supported:
+	  - IR
+
+config HID_PICOLCD_FB
+	bool "Framebuffer support" if EMBEDDED
+	default !EMBEDDED
+	depends on HID_PICOLCD
+	depends on HID_PICOLCD=FB || FB=y
+	select FB_DEFERRED_IO
+	select FB_SYS_FILLRECT
+	select FB_SYS_COPYAREA
+	select FB_SYS_IMAGEBLIT
+	select FB_SYS_FOPS
+	---help---
+	  Provide access to PicoLCD's 256x64 monochrome display via a
+	  frambuffer device.
+
+config HID_PICOLCD_BACKLIGHT
+	bool "Backlight control" if EMBEDDED
+	default !EMBEDDED
+	depends on HID_PICOLCD
+	depends on HID_PICOLCD=BACKLIGHT_CLASS_DEVICE || BACKLIGHT_CLASS_DEVICE=y
+	---help---
+	  Provide access to PicoLCD's backlight control via backlight
+	  class.
+
+config HID_PICOLCD_LCD
+	bool "Contrast control" if EMBEDDED
+	default !EMBEDDED
+	depends on HID_PICOLCD
+	depends on HID_PICOLCD=LCD_CLASS_DEVICE || LCD_CLASS_DEVICE=y
+	---help---
+	  Provide access to PicoLCD's LCD contrast via lcd class.
+
+config HID_PICOLCD_LEDS
+	bool "GPO via leds class" if EMBEDDED
+	default !EMBEDDED
+	depends on HID_PICOLCD
+	depends on HID_PICOLCD=LEDS_CLASS || LEDS_CLASS=y
+	---help---
+	  Provide access to PicoLCD's GPO pins via leds class.
+
 config HID_QUANTA
 	tristate "Quanta Optical Touch"
 	depends on USB_HID
 	---help---
 	Support for Quanta Optical Touch dual-touch panels.
 
+config HID_ROCCAT_KONE
+	tristate "Roccat Kone Mouse support"
+	depends on USB_HID
+	---help---
+	Support for Roccat Kone mouse.
+
 config HID_SAMSUNG
 	tristate "Samsung" if EMBEDDED
 	depends on USB_HID

drivers/hid/Makefile

@@ -43,9 +43,12 @@ obj-$(CONFIG_HID_MONTEREY)	+= hid-monterey.o
 obj-$(CONFIG_HID_MOSART)	+= hid-mosart.o
 obj-$(CONFIG_HID_NTRIG)		+= hid-ntrig.o
 obj-$(CONFIG_HID_ORTEK)		+= hid-ortek.o
+obj-$(CONFIG_HID_PRODIKEYS)	+= hid-prodikeys.o
 obj-$(CONFIG_HID_QUANTA)	+= hid-quanta.o
 obj-$(CONFIG_HID_PANTHERLORD)	+= hid-pl.o
 obj-$(CONFIG_HID_PETALYNX)	+= hid-petalynx.o
+obj-$(CONFIG_HID_PICOLCD)	+= hid-picolcd.o
+obj-$(CONFIG_HID_ROCCAT_KONE)	+= hid-roccat-kone.o
 obj-$(CONFIG_HID_SAMSUNG)	+= hid-samsung.o
 obj-$(CONFIG_HID_SMARTJOYPLUS)	+= hid-sjoy.o
 obj-$(CONFIG_HID_SONY)		+= hid-sony.o

drivers/hid/hid-core.c

@@ -1287,6 +1287,7 @@ static const struct hid_device_id hid_blacklist[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CHERRY, USB_DEVICE_ID_CHERRY_CYMOTION) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CHERRY, USB_DEVICE_ID_CHERRY_CYMOTION_SOLAR) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CHICONY, USB_DEVICE_ID_CHICONY_TACTICAL_PAD) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_CREATIVELABS, USB_DEVICE_ID_PRODIKEYS_PCMIDI) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CYPRESS, USB_DEVICE_ID_CYPRESS_BARCODE_1) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CYPRESS, USB_DEVICE_ID_CYPRESS_BARCODE_2) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_CYPRESS, USB_DEVICE_ID_CYPRESS_BARCODE_3) },
@@ -1326,6 +1327,8 @@ static const struct hid_device_id hid_blacklist[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_LOGITECH_RUMBLEPAD2) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACETRAVELLER) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACENAVIGATOR) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD_BOOTLOADER) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_SIDEWINDER_GV) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_NE4K) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_LK6K) },
@@ -1337,6 +1340,7 @@ static const struct hid_device_id hid_blacklist[] = {
 	{ HID_USB_DEVICE(USB_VENDOR_ID_PETALYNX, USB_DEVICE_ID_PETALYNX_MAXTER_REMOTE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_QUANTA, USB_DEVICE_ID_QUANTA_OPTICAL_TOUCH) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_QUANTA, USB_DEVICE_ID_PIXART_IMAGING_INC_OPTICAL_TOUCH_SCREEN) },
+	{ HID_USB_DEVICE(USB_VENDOR_ID_ROCCAT, USB_DEVICE_ID_ROCCAT_KONE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SAMSUNG, USB_DEVICE_ID_SAMSUNG_IR_REMOTE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SAMSUNG, USB_DEVICE_ID_SAMSUNG_WIRELESS_KBD_MOUSE) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_SONY, USB_DEVICE_ID_SONY_PS3_CONTROLLER) },

drivers/hid/hid-ids.h

@@ -156,6 +156,9 @@
 #define USB_DEVICE_ID_CODEMERCS_IOW_FIRST	0x1500
 #define USB_DEVICE_ID_CODEMERCS_IOW_LAST	0x15ff
 
+#define USB_VENDOR_ID_CREATIVELABS	0x041e
+#define USB_DEVICE_ID_PRODIKEYS_PCMIDI	0x2801
+
 #define USB_VENDOR_ID_CYGNAL		0x10c4
 #define USB_DEVICE_ID_CYGNAL_RADIO_SI470X	0x818a
 
@@ -354,6 +357,8 @@
 #define USB_VENDOR_ID_MICROCHIP		0x04d8
 #define USB_DEVICE_ID_PICKIT1		0x0032
 #define USB_DEVICE_ID_PICKIT2		0x0033
+#define USB_DEVICE_ID_PICOLCD		0xc002
+#define USB_DEVICE_ID_PICOLCD_BOOTLOADER	0xf002
 
 #define USB_VENDOR_ID_MICROSOFT		0x045e
 #define USB_DEVICE_ID_SIDEWINDER_GV	0x003b
@@ -412,6 +417,9 @@
 #define USB_VENDOR_ID_PRODIGE		0x05af
 #define USB_DEVICE_ID_PRODIGE_CORDLESS	0x3062
 
+#define USB_VENDOR_ID_ROCCAT		0x1e7d
+#define USB_DEVICE_ID_ROCCAT_KONE	0x2ced
+
 #define USB_VENDOR_ID_SAITEK		0x06a3
 #define USB_DEVICE_ID_SAITEK_RUMBLEPAD	0xff17