Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/ker…

…nel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2018-01-11

Here's likely the last bluetooth-next pull request for the 4.16 kernel.

 - Added support for Bluetooth on 2015+ MacBook (Pro)
 - Fix to QCA Rome suspend/resume handling
 - Two new QCA_ROME USB IDs in btusb
 - A few other minor fixes

Please let me know if there are any issues pulling. Thanks.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/bluetooth/Kconfig

@@ -77,6 +77,7 @@ config BT_HCIBTSDIO
 config BT_HCIUART
 	tristate "HCI UART driver"
 	depends on SERIAL_DEV_BUS || !SERIAL_DEV_BUS
+	depends on NVMEM || !NVMEM
 	depends on TTY
 	help
 	  Bluetooth HCI UART driver.
@@ -107,6 +108,7 @@ config BT_HCIUART_NOKIA
 	tristate "UART Nokia H4+ protocol support"
 	depends on BT_HCIUART
 	depends on BT_HCIUART_SERDEV
+	depends on GPIOLIB
 	depends on PM
 	select BT_HCIUART_H4
 	select BT_BCM
@@ -168,6 +170,7 @@ config BT_HCIUART_3WIRE
 config BT_HCIUART_INTEL
 	bool "Intel protocol support"
 	depends on BT_HCIUART
+	depends on GPIOLIB
 	select BT_HCIUART_H4
 	select BT_INTEL
 	help
@@ -181,6 +184,7 @@ config BT_HCIUART_BCM
 	depends on BT_HCIUART
 	depends on BT_HCIUART_SERDEV
 	depends on (!ACPI || SERIAL_DEV_CTRL_TTYPORT)
+	depends on GPIOLIB
 	select BT_HCIUART_H4
 	select BT_BCM
 	help

drivers/bluetooth/bpa10x.c

@@ -259,7 +259,7 @@ static int bpa10x_flush(struct hci_dev *hdev)
 
 static int bpa10x_setup(struct hci_dev *hdev)
 {
-	const u8 req[] = { 0x07 };
+	static const u8 req[] = { 0x07 };
 	struct sk_buff *skb;
 
 	BT_DBG("%s", hdev->name);

drivers/bluetooth/btbcm.h

@@ -44,8 +44,8 @@ struct bcm_set_sleep_mode {
 	__u8 tristate_control;
 	__u8 usb_auto_sleep;
 	__u8 usb_resume_timeout;
-	__u8 pulsed_host_wake;
 	__u8 break_to_host;
+	__u8 pulsed_host_wake;
 } __packed;
 
 struct bcm_set_pcm_int_params {

drivers/bluetooth/btintel.c

@@ -75,7 +75,7 @@ EXPORT_SYMBOL_GPL(btintel_check_bdaddr);
 
 int btintel_enter_mfg(struct hci_dev *hdev)
 {
-	const u8 param[] = { 0x01, 0x00 };
+	static const u8 param[] = { 0x01, 0x00 };
 	struct sk_buff *skb;
 
 	skb = __hci_cmd_sync(hdev, 0xfc11, 2, param, HCI_CMD_TIMEOUT);

drivers/bluetooth/btusb.c

@@ -23,6 +23,7 @@
 
 #include <linux/module.h>
 #include <linux/usb.h>
+#include <linux/usb/quirks.h>
 #include <linux/firmware.h>
 #include <linux/of_device.h>
 #include <linux/of_irq.h>
@@ -264,13 +265,15 @@ static const struct usb_device_id blacklist_table[] = {
 	/* QCA ROME chipset */
 	{ USB_DEVICE(0x0cf3, 0xe007), .driver_info = BTUSB_QCA_ROME },
 	{ USB_DEVICE(0x0cf3, 0xe009), .driver_info = BTUSB_QCA_ROME },
+	{ USB_DEVICE(0x0cf3, 0xe010), .driver_info = BTUSB_QCA_ROME },
 	{ USB_DEVICE(0x0cf3, 0xe300), .driver_info = BTUSB_QCA_ROME },
 	{ USB_DEVICE(0x0cf3, 0xe301), .driver_info = BTUSB_QCA_ROME },
 	{ USB_DEVICE(0x0cf3, 0xe360), .driver_info = BTUSB_QCA_ROME },
 	{ USB_DEVICE(0x0489, 0xe092), .driver_info = BTUSB_QCA_ROME },
 	{ USB_DEVICE(0x0489, 0xe09f), .driver_info = BTUSB_QCA_ROME },
 	{ USB_DEVICE(0x0489, 0xe0a2), .driver_info = BTUSB_QCA_ROME },
 	{ USB_DEVICE(0x04ca, 0x3011), .driver_info = BTUSB_QCA_ROME },
+	{ USB_DEVICE(0x04ca, 0x3015), .driver_info = BTUSB_QCA_ROME },
 	{ USB_DEVICE(0x04ca, 0x3016), .driver_info = BTUSB_QCA_ROME },
 
 	/* Broadcom BCM2035 */
@@ -388,9 +391,8 @@ static const struct usb_device_id blacklist_table[] = {
 #define BTUSB_FIRMWARE_LOADED	7
 #define BTUSB_FIRMWARE_FAILED	8
 #define BTUSB_BOOTING		9
-#define BTUSB_RESET_RESUME	10
-#define BTUSB_DIAG_RUNNING	11
-#define BTUSB_OOB_WAKE_ENABLED	12
+#define BTUSB_DIAG_RUNNING	10
+#define BTUSB_OOB_WAKE_ENABLED	11
 
 struct btusb_data {
 	struct hci_dev       *hdev;
@@ -3121,9 +3123,9 @@ static int btusb_probe(struct usb_interface *intf,
 
 		/* QCA Rome devices lose their updated firmware over suspend,
 		 * but the USB hub doesn't notice any status change.
-		 * Explicitly request a device reset on resume.
+		 * explicitly request a device reset on resume.
 		 */
-		set_bit(BTUSB_RESET_RESUME, &data->flags);
+		interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME;
 	}
 
 #ifdef CONFIG_BT_HCIBTUSB_RTL
@@ -3134,7 +3136,7 @@ static int btusb_probe(struct usb_interface *intf,
 		 * but the USB hub doesn't notice any status change.
 		 * Explicitly request a device reset on resume.
 		 */
-		set_bit(BTUSB_RESET_RESUME, &data->flags);
+		interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME;
 	}
 #endif
 
@@ -3303,14 +3305,6 @@ static int btusb_suspend(struct usb_interface *intf, pm_message_t message)
 		enable_irq(data->oob_wake_irq);
 	}
 
-	/* Optionally request a device reset on resume, but only when
-	 * wakeups are disabled. If wakeups are enabled we assume the
-	 * device will stay powered up throughout suspend.
-	 */
-	if (test_bit(BTUSB_RESET_RESUME, &data->flags) &&
-	    !device_may_wakeup(&data->udev->dev))
-		data->udev->reset_resume = 1;
-
 	return 0;
 }