Merge remote-tracking branches 'asoc/topic/nau8825' and 'asoc/topic/p…

…xa' into asoc-next

Documentation/devicetree/bindings/sound/nau8825.txt

@@ -0,0 +1,102 @@
+Nuvoton NAU8825 audio codec
+
+This device supports I2C only.
+
+Required properties:
+  - compatible : Must be "nuvoton,nau8825"
+
+  - reg : the I2C address of the device. This is either 0x1a (CSB=0) or 0x1b (CSB=1).
+
+Optional properties:
+  - nuvoton,jkdet-enable: Enable jack detection via JKDET pin.
+  - nuvoton,jkdet-pull-enable: Enable JKDET pin pull. If set - pin pull enabled,
+      otherwise pin in high impedance state.
+  - nuvoton,jkdet-pull-up: Pull-up JKDET pin. If set then JKDET pin is pull up, otherwise pull down.
+  - nuvoton,jkdet-polarity: JKDET pin polarity. 0 - active high, 1 - active low.
+
+  - nuvoton,vref-impedance: VREF Impedance selection
+      0 - Open
+      1 - 25 kOhm
+      2 - 125 kOhm
+      3 - 2.5 kOhm
+
+  - nuvoton,micbias-voltage: Micbias voltage level.
+      0 - VDDA
+      1 - VDDA
+      2 - VDDA * 1.1
+      3 - VDDA * 1.2
+      4 - VDDA * 1.3
+      5 - VDDA * 1.4
+      6 - VDDA * 1.53
+      7 - VDDA * 1.53
+
+  - nuvoton,sar-threshold-num: Number of buttons supported
+  - nuvoton,sar-threshold: Impedance threshold for each button. Array that contains up to 8 buttons configuration. SAR value is calculated as
+    SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R)
+    where MICBIAS is configured by 'nuvoton,micbias-voltage', SAR_VOLTAGE is configured by 'nuvoton,sar-voltage', R - button impedance.
+    Refer datasheet section 10.2 for more information about threshold calculation.
+
+  - nuvoton,sar-hysteresis: Button impedance measurement hysteresis.
+
+  - nuvoton,sar-voltage: Reference voltage for button impedance measurement.
+      0 - VDDA
+      1 - VDDA
+      2 - VDDA * 1.1
+      3 - VDDA * 1.2
+      4 - VDDA * 1.3
+      5 - VDDA * 1.4
+      6 - VDDA * 1.53
+      7 - VDDA * 1.53
+
+  - nuvoton,sar-compare-time: SAR compare time
+      0 - 500 ns
+      1 - 1 us
+      2 - 2 us
+      3 - 4 us
+
+  - nuvoton,sar-sampling-time: SAR sampling time
+      0 - 2 us
+      1 - 4 us
+      2 - 8 us
+      3 - 16 us
+
+  - nuvoton,short-key-debounce: Button short key press debounce time.
+      0 - 30 ms
+      1 - 50 ms
+      2 - 100 ms
+      3 - 30 ms
+
+  - nuvoton,jack-insert-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
+  - nuvoton,jack-eject-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
+
+  - clocks: list of phandle and clock specifier pairs according to common clock bindings for the
+      clocks described in clock-names
+  - clock-names: should include "mclk" for the MCLK master clock
+
+Example:
+
+  headset: nau8825@1a {
+      compatible = "nuvoton,nau8825";
+      reg = <0x1a>;
+      interrupt-parent = <&gpio>;
+      interrupts = <TEGRA_GPIO(E, 6) IRQ_TYPE_LEVEL_LOW>;
+      nuvoton,jkdet-enable;
+      nuvoton,jkdet-pull-enable;
+      nuvoton,jkdet-pull-up;
+      nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>;
+      nuvoton,vref-impedance = <2>;
+      nuvoton,micbias-voltage = <6>;
+      // Setup 4 buttons impedance according to Android specification
+      nuvoton,sar-threshold-num = <4>;
+      nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>;
+      nuvoton,sar-hysteresis = <1>;
+      nuvoton,sar-voltage = <0>;
+      nuvoton,sar-compare-time = <0>;
+      nuvoton,sar-sampling-time = <0>;
+      nuvoton,short-key-debounce = <2>;
+      nuvoton,jack-insert-debounce = <7>;
+      nuvoton,jack-eject-debounce = <7>;
+
+      clock-names = "mclk";
+      clocks = <&tegra_car TEGRA210_CLK_CLK_OUT_2>;
+  };

include/sound/pxa2xx-lib.h

@@ -12,7 +12,6 @@ extern int __pxa2xx_pcm_hw_free(struct snd_pcm_substream *substream);
 extern int pxa2xx_pcm_trigger(struct snd_pcm_substream *substream, int cmd);
 extern snd_pcm_uframes_t pxa2xx_pcm_pointer(struct snd_pcm_substream *substream);
 extern int __pxa2xx_pcm_prepare(struct snd_pcm_substream *substream);
-extern void pxa2xx_pcm_dma_irq(int dma_ch, void *dev_id);
 extern int __pxa2xx_pcm_open(struct snd_pcm_substream *substream);
 extern int __pxa2xx_pcm_close(struct snd_pcm_substream *substream);
 extern int pxa2xx_pcm_mmap(struct snd_pcm_substream *substream,

sound/arm/pxa2xx-ac97.c

@@ -15,6 +15,7 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/dmaengine.h>
+#include <linux/dma/pxa-dma.h>
 
 #include <sound/core.h>
 #include <sound/pcm.h>
@@ -43,15 +44,23 @@ static struct snd_ac97_bus_ops pxa2xx_ac97_ops = {
 	.reset	= pxa2xx_ac97_reset,
 };
 
-static unsigned long pxa2xx_ac97_pcm_out_req = 12;
+static struct pxad_param pxa2xx_ac97_pcm_out_req = {
+	.prio = PXAD_PRIO_LOWEST,
+	.drcmr = 12,
+};
+
 static struct snd_dmaengine_dai_dma_data pxa2xx_ac97_pcm_out = {
 	.addr		= __PREG(PCDR),
 	.addr_width	= DMA_SLAVE_BUSWIDTH_4_BYTES,
 	.maxburst	= 32,
 	.filter_data	= &pxa2xx_ac97_pcm_out_req,
 };
 
-static unsigned long pxa2xx_ac97_pcm_in_req = 11;
+static struct pxad_param pxa2xx_ac97_pcm_in_req = {
+	.prio = PXAD_PRIO_LOWEST,
+	.drcmr = 11,
+};
+
 static struct snd_dmaengine_dai_dma_data pxa2xx_ac97_pcm_in = {
 	.addr		= __PREG(PCDR),
 	.addr_width	= DMA_SLAVE_BUSWIDTH_4_BYTES,