Merge branch 'for-5.16-vsprintf-pgp' into for-linus

Documentation/ABI/stable/sysfs-driver-dma-idxd

@@ -128,6 +128,8 @@ Date:		Aug 28, 2020
 KernelVersion:	5.10.0
 Contact:	dmaengine@vger.kernel.org
 Description:	The last executed device administrative command's status/error.
+		Also last configuration error overloaded.
+		Writing to it will clear the status.
 
 What:		/sys/bus/dsa/devices/wq<m>.<n>/block_on_fault
 Date:		Oct 27, 2020
@@ -211,6 +213,13 @@ Contact:	dmaengine@vger.kernel.org
 Description:	Indicate whether ATS disable is turned on for the workqueue.
 		0 indicates ATS is on, and 1 indicates ATS is off for the workqueue.
 
+What:		/sys/bus/dsa/devices/wq<m>.<n>/occupancy
+Date		May 25, 2021
+KernelVersion:	5.14.0
+Contact:	dmaengine@vger.kernel.org
+Description:	Show the current number of entries in this WQ if WQ Occupancy
+		Support bit WQ capabilities is 1.
+
 What:           /sys/bus/dsa/devices/engine<m>.<n>/group_id
 Date:           Oct 25, 2019
 KernelVersion:  5.6.0

Documentation/ABI/testing/debugfs-driver-habanalabs

@@ -215,6 +215,17 @@ Description:    Sets the skip reset on timeout option for the device. Value of
                 "0" means device will be reset in case some CS has timed out,
                 otherwise it will not be reset.
 
+What:           /sys/kernel/debug/habanalabs/hl<n>/state_dump
+Date:           Oct 2021
+KernelVersion:  5.15
+Contact:        ynudelman@habana.ai
+Description:    Gets the state dump occurring on a CS timeout or failure.
+                State dump is used for debug and is created each time in case of
+                a problem in a CS execution, before reset.
+                Reading from the node returns the newest state dump available.
+                Writing an integer X discards X state dumps, so that the
+                next read would return X+1-st newest state dump.
+
 What:           /sys/kernel/debug/habanalabs/hl<n>/stop_on_err
 Date:           Mar 2020
 KernelVersion:  5.6
@@ -230,6 +241,14 @@ Description:    Displays a list with information about the currently user
                 pointers (user virtual addresses) that are pinned and mapped
                 to DMA addresses
 
+What:           /sys/kernel/debug/habanalabs/hl<n>/userptr_lookup
+Date:           Aug 2021
+KernelVersion:  5.15
+Contact:        ogabbay@kernel.org
+Description:    Allows to search for specific user pointers (user virtual
+                addresses) that are pinned and mapped to DMA addresses, and see
+                their resolution to the specific dma address.
+
 What:           /sys/kernel/debug/habanalabs/hl<n>/vm
 Date:           Jan 2019
 KernelVersion:  5.1

Documentation/ABI/testing/dell-smbios-wmi

@@ -1,7 +1,7 @@
 What:		/dev/wmi/dell-smbios
 Date:		November 2017
 KernelVersion:	4.15
-Contact:	"Mario Limonciello" <mario.limonciello@dell.com>
+Contact:	Dell.Client.Kernel@dell.com
 Description:
 		Perform SMBIOS calls on supported Dell machines.
 		through the Dell ACPI-WMI interface.

Documentation/ABI/testing/ima_policy

@@ -27,12 +27,13 @@ Description:
 			lsm:	[[subj_user=] [subj_role=] [subj_type=]
 				 [obj_user=] [obj_role=] [obj_type=]]
 			option:	[[appraise_type=]] [template=] [permit_directio]
-				[appraise_flag=] [keyrings=]
+				[appraise_flag=] [appraise_algos=] [keyrings=]
 		  base:
 			func:= [BPRM_CHECK][MMAP_CHECK][CREDS_CHECK][FILE_CHECK][MODULE_CHECK]
-			        [FIRMWARE_CHECK]
+				[FIRMWARE_CHECK]
 				[KEXEC_KERNEL_CHECK] [KEXEC_INITRAMFS_CHECK]
 				[KEXEC_CMDLINE] [KEY_CHECK] [CRITICAL_DATA]
+				[SETXATTR_CHECK]
 			mask:= [[^]MAY_READ] [[^]MAY_WRITE] [[^]MAY_APPEND]
 			       [[^]MAY_EXEC]
 			fsmagic:= hex value
@@ -55,6 +56,10 @@ Description:
 			label:= [selinux]|[kernel_info]|[data_label]
 			data_label:= a unique string used for grouping and limiting critical data.
 			For example, "selinux" to measure critical data for SELinux.
+			appraise_algos:= comma-separated list of hash algorithms
+			For example, "sha256,sha512" to only accept to appraise
+			files where the security.ima xattr was hashed with one
+			of these two algorithms.
 
 		  default policy:
 			# PROC_SUPER_MAGIC
@@ -134,3 +139,9 @@ Description:
 		keys added to .builtin_trusted_keys or .ima keyring:
 
 			measure func=KEY_CHECK keyrings=.builtin_trusted_keys|.ima
+
+		Example of the special SETXATTR_CHECK appraise rule, that
+		restricts the hash algorithms allowed when writing to the
+		security.ima xattr of a file:
+
+			appraise func=SETXATTR_CHECK appraise_algos=sha256,sha384,sha512

Documentation/ABI/testing/sysfs-bus-pci

@@ -121,6 +121,23 @@ Description:
 		child buses, and re-discover devices removed earlier
 		from this part of the device tree.
 
+What:		/sys/bus/pci/devices/.../reset_method
+Date:		August 2021
+Contact:	Amey Narkhede <ameynarkhede03@gmail.com>
+Description:
+		Some devices allow an individual function to be reset
+		without affecting other functions in the same slot.
+
+		For devices that have this support, a file named
+		reset_method is present in sysfs.  Reading this file
+		gives names of the supported and enabled reset methods and
+		their ordering.  Writing a space-separated list of names of
+		reset methods sets the reset methods and ordering to be
+		used when resetting the device.  Writing an empty string
+		disables the ability to reset the device.  Writing
+		"default" enables all supported reset methods in the
+		default ordering.
+
 What:		/sys/bus/pci/devices/.../reset
 Date:		July 2009
 Contact:	Michael S. Tsirkin <mst@redhat.com>

Documentation/ABI/testing/sysfs-bus-thunderbolt

@@ -232,7 +232,7 @@ Description:	When new NVM image is written to the non-active NVM
 What:		/sys/bus/thunderbolt/devices/.../nvm_authenticate_on_disconnect
 Date:		Oct 2020
 KernelVersion:	v5.9
-Contact:	Mario Limonciello <mario.limonciello@dell.com>
+Contact:	Mario Limonciello <mario.limonciello@outlook.com>
 Description:	For supported devices, automatically authenticate the new Thunderbolt
 		image when the device is disconnected from the host system.
 

Documentation/ABI/testing/sysfs-class-firmware-attributes

@@ -2,8 +2,8 @@ What:		/sys/class/firmware-attributes/*/attributes/*/
 Date:		February 2021
 KernelVersion:	5.11
 Contact:	Divya Bharathi <Divya.Bharathi@Dell.com>,
-		Mario Limonciello <mario.limonciello@dell.com>,
 		Prasanth KSR <prasanth.ksr@dell.com>
+		Dell.Client.Kernel@dell.com
 Description:
 		A sysfs interface for systems management software to enable
 		configuration capability on supported systems.  This directory
@@ -130,8 +130,8 @@ What:		/sys/class/firmware-attributes/*/authentication/
 Date:		February 2021
 KernelVersion:	5.11
 Contact:	Divya Bharathi <Divya.Bharathi@Dell.com>,
-		Mario Limonciello <mario.limonciello@dell.com>,
 		Prasanth KSR <prasanth.ksr@dell.com>
+		Dell.Client.Kernel@dell.com
 Description:
 		Devices support various authentication mechanisms which can be exposed
 		as a separate configuration object.
@@ -220,8 +220,8 @@ What:		/sys/class/firmware-attributes/*/attributes/pending_reboot
 Date:		February 2021
 KernelVersion:	5.11
 Contact:	Divya Bharathi <Divya.Bharathi@Dell.com>,
-		Mario Limonciello <mario.limonciello@dell.com>,
 		Prasanth KSR <prasanth.ksr@dell.com>
+		Dell.Client.Kernel@dell.com
 Description:
 		A read-only attribute reads 1 if a reboot is necessary to apply
 		pending BIOS attribute changes. Also, an uevent_KOBJ_CHANGE is
@@ -249,8 +249,8 @@ What:		/sys/class/firmware-attributes/*/attributes/reset_bios
 Date:		February 2021
 KernelVersion:	5.11
 Contact:	Divya Bharathi <Divya.Bharathi@Dell.com>,
-		Mario Limonciello <mario.limonciello@dell.com>,
 		Prasanth KSR <prasanth.ksr@dell.com>
+		Dell.Client.Kernel@dell.com
 Description:
 		This attribute can be used to reset the BIOS Configuration.
 		Specifically, it tells which type of reset BIOS configuration is being
@@ -272,3 +272,14 @@ Description:
 
 		Note that any changes to this attribute requires a reboot
 		for changes to take effect.
+
+What:		/sys/class/firmware-attributes/*/attributes/debug_cmd
+Date:		July 2021
+KernelVersion:	5.14
+Contact:	Mark Pearson <markpearson@lenovo.com>
+Description:
+		This write only attribute can be used to send debug commands to the BIOS.
+		This should only be used when recommended by the BIOS vendor. Vendors may
+		use it to enable extra debug attributes or BIOS features for testing purposes.
+
+		Note that any changes to this attribute requires a reboot for changes to take effect.

Documentation/ABI/testing/sysfs-driver-intc_sar

@@ -0,0 +1,54 @@
+What:		/sys/bus/platform/devices/INTC1092:00/intc_reg
+Date:		August 2021
+KernelVersion:	5.15
+Contact:	Shravan S <s.shravan@intel.com>,
+		An Sudhakar <sudhakar.an@intel.com>
+Description:
+		Specific Absorption Rate (SAR) regulatory mode is typically
+		derived based on information like mcc (Mobile Country Code) and
+		mnc (Mobile Network Code) that is available for the currently
+		attached LTE network. A userspace application is required to set
+		the current SAR regulatory mode on the Dynamic SAR driver using
+		this sysfs node. Such an application can also read back using
+		this sysfs node, the currently configured regulatory mode value
+		from the Dynamic SAR driver.
+
+		Acceptable regulatory modes are:
+			==	====
+			0	FCC
+			1	CE
+			2	ISED
+			==	====
+
+		- The regulatory mode value has one of the above values.
+		- The default regulatory mode used in the driver is 0.
+
+What:		/sys/bus/platform/devices/INTC1092:00/intc_data
+Date:		August 2021
+KernelVersion:	5.15
+Contact:	Shravan S <s.shravan@intel.com>,
+		An Sudhakar <sudhakar.an@intel.com>
+Description:
+		This sysfs entry is used to retrieve Dynamic SAR information
+		emitted/maintained by a BIOS that supports Dynamic SAR.
+
+		The retrieved information is in the order given below:
+		- device_mode
+		- bandtable_index
+		- antennatable_index
+		- sartable_index
+
+		The above information is sent as integer values separated
+		by a single space. This information can then be pushed to a
+		WWAN modem that uses this to control the transmit signal
+		level using the Band/Antenna/SAR table index information.
+		These parameters are derived/decided by aggregating
+		device-mode like laptop/tablet/clamshell etc. and the
+		proximity-sensor data available to the embedded controller on
+		given host. The regulatory mode configured on Dynamic SAR
+		driver also influences these values.
+
+		The userspace applications can poll for changes to this file
+		using POLLPRI event on file-descriptor (fd) obtained by opening
+		this sysfs entry. Application can then read this information from
+		the sysfs node and consume the given information.