Merge tag 'drm-next-2018-10-24' of git://anongit.freedesktop.org/drm/drm

Pull drm updates from Dave Airlie:
 "This is going to rebuild more than drm as it adds a new helper to
  list.h for doing bulk updates. Seemed like a reasonable addition to
  me.

  Otherwise the usual merge window stuff lots of i915 and amdgpu, not so
  much nouveau, and piles of everything else.

  Core:
   - Adds a new list.h helper for doing bulk list updates for TTM.
   - Don't leak fb address in smem_start to userspace (comes with EXPORT
     workaround for people using mali out of tree hacks)
   - udmabuf device to turn memfd regions into dma-buf
   - Per-plane blend mode property
   - ref/unref replacements with get/put
   - fbdev conflicting framebuffers code cleaned up
   - host-endian format variants
   - panel orientation quirk for Acer One 10

  bridge:
   - TI SN65DSI86 chip support

  vkms:
   - GEM support.
   - Cursor support

  amdgpu:
   - Merge amdkfd and amdgpu into one module
   - CEC over DP AUX support
   - Picasso APU support + VCN dynamic powergating
   - Raven2 APU support
   - Vega20 enablement + kfd support
   - ACP powergating improvements
   - ABGR/XBGR display support
   - VCN jpeg support
   - xGMI support
   - DC i2c/aux cleanup
   - Ycbcr 4:2:0 support
   - GPUVM improvements
   - Powerplay and powerplay endian fixes
   - Display underflow fixes

  vmwgfx:
   - Move vmwgfx specific TTM code to vmwgfx
   - Split out vmwgfx buffer/resource validation code
   - Atomic operation rework

  bochs:
   - use more helpers
   - format/byteorder improvements

  qxl:
   - use more helpers

  i915:
   - GGTT coherency getparam
   - Turn off resource streamer API
   - More Icelake enablement + DMC firmware
   - Full PPGTT for Ivybridge, Haswell and Valleyview
   - DDB distribution based on resolution
   - Limited range DP display support

  nouveau:
   - CEC over DP AUX support
   - Initial HDMI 2.0 support

  virtio-gpu:
   - vmap support for PRIME objects

  tegra:
   - Initial Tegra194 support
   - DMA/IOMMU integration fixes

  msm:
   - a6xx perf improvements + clock prefix
   - GPU preemption optimisations
   - a6xx devfreq support
   - cursor support

  rockchip:
   - PX30 support
   - rgb output interface support

  mediatek:
   - HDMI output support on mt2701 and mt7623

  rcar-du:
   - Interlaced modes on Gen3
   - LVDS on R8A77980
   - D3 and E3 SoC support

  hisilicon:
   - misc fixes

  mxsfb:
   - runtime pm support

  sun4i:
   - R40 TCON support
   - Allwinner A64 support
   - R40 HDMI support

  omapdrm:
   - Driver rework changing display pipeline ordering to use common code
   - DMM memory barrier and irq fixes
   - Errata workarounds

  exynos:
   - out-bridge support for LVDS bridge driver
   - Samsung 16x16 tiled format support
   - Plane alpha and pixel blend mode support

  tilcdc:
   - suspend/resume update

  mali-dp:
   - misc updates"

* tag 'drm-next-2018-10-24' of git://anongit.freedesktop.org/drm/drm: (1382 commits)
  firmware/dmc/icl: Add missing MODULE_FIRMWARE() for Icelake.
  drm/i915/icl: Fix signal_levels
  drm/i915/icl: Fix DDI/TC port clk_off bits
  drm/i915/icl: create function to identify combophy port
  drm/i915/gen9+: Fix initial readout for Y tiled framebuffers
  drm/i915: Large page offsets for pread/pwrite
  drm/i915/selftests: Disable shrinker across mmap-exhaustion
  drm/i915/dp: Link train Fallback on eDP only if fallback link BW can fit panel's native mode
  drm/i915: Fix intel_dp_mst_best_encoder()
  drm/i915: Skip vcpi allocation for MSTB ports that are gone
  drm/i915: Don't unset intel_connector->mst_port
  drm/i915: Only reset seqno if actually idle
  drm/i915: Use the correct crtc when sanitizing plane mapping
  drm/i915: Restore vblank interrupts earlier
  drm/i915: Check fb stride against plane max stride
  drm/amdgpu/vcn:Fix uninitialized symbol error
  drm: panel-orientation-quirks: Add quirk for Acer One 10 (S1003)
  drm/amd/amdgpu: Fix debugfs error handling
  drm/amdgpu: Update gc_9_0 golden settings.
  drm/amd/powerplay: update PPtable with DC BTC and Tvr SocLimit fields
  ...

Documentation/devicetree/bindings/display/atmel/hlcdc-dc.txt

@@ -15,6 +15,13 @@ Required children nodes:
  to external devices using the OF graph reprensentation (see ../graph.txt).
  At least one port node is required.
 
+Optional properties in grandchild nodes:
+ Any endpoint grandchild node may specify a desired video interface
+ according to ../../media/video-interfaces.txt, specifically
+ - bus-width: recognized values are <12>, <16>, <18> and <24>, and
+   override any output mode selection heuristic, forcing "rgb444",
+   "rgb565", "rgb666" and "rgb888" respectively.
+
 Example:
 
 	hlcdc: hlcdc@f0030000 {
@@ -50,3 +57,19 @@ Example:
 			#pwm-cells = <3>;
 		};
 	};
+
+Example 2: With a video interface override to force rgb565; as above
+but with these changes/additions:
+
+	&hlcdc {
+		hlcdc-display-controller {
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb565>;
+
+			port@0 {
+				hlcdc_panel_output: endpoint@0 {
+					bus-width = <16>;
+				};
+			};
+		};
+	};

Documentation/devicetree/bindings/display/bridge/lvds-transmitter.txt

@@ -22,7 +22,13 @@ among others.
 
 Required properties:
 
-- compatible: Must be "lvds-encoder"
+- compatible: Must be one or more of the following
+  - "ti,ds90c185" for the TI DS90C185 FPD-Link Serializer
+  - "lvds-encoder" for a generic LVDS encoder device
+
+  When compatible with the generic version, nodes must list the
+  device-specific version corresponding to the device first
+  followed by the generic version.
 
 Required nodes:
 

Documentation/devicetree/bindings/display/bridge/renesas,lvds.txt

@@ -14,10 +14,22 @@ Required properties:
   - "renesas,r8a7795-lvds" for R8A7795 (R-Car H3) compatible LVDS encoders
   - "renesas,r8a7796-lvds" for R8A7796 (R-Car M3-W) compatible LVDS encoders
   - "renesas,r8a77970-lvds" for R8A77970 (R-Car V3M) compatible LVDS encoders
+  - "renesas,r8a77980-lvds" for R8A77980 (R-Car V3H) compatible LVDS encoders
+  - "renesas,r8a77990-lvds" for R8A77990 (R-Car E3) compatible LVDS encoders
   - "renesas,r8a77995-lvds" for R8A77995 (R-Car D3) compatible LVDS encoders
 
 - reg: Base address and length for the memory-mapped registers
-- clocks: A phandle + clock-specifier pair for the functional clock
+- clocks: A list of phandles + clock-specifier pairs, one for each entry in
+  the clock-names property.
+- clock-names: Name of the clocks. This property is model-dependent.
+  - The functional clock, which mandatory for all models, shall be listed
+    first, and shall be named "fck".
+  - On R8A77990 and R8A77995, the LVDS encoder can use the EXTAL or
+    DU_DOTCLKINx clocks. Those clocks are optional. When supplied they must be
+    named "extal" and "dclkin.x" respectively, with "x" being the DU_DOTCLKIN
+    numerical index.
+  - When the clocks property only contains the functional clock, the
+    clock-names property may be omitted.
 - resets: A phandle + reset specifier for the module reset
 
 Required nodes:

Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt

@@ -0,0 +1,87 @@
+SN65DSI86 DSI to eDP bridge chip
+--------------------------------
+
+This is the binding for Texas Instruments SN65DSI86 bridge.
+http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf
+
+Required properties:
+- compatible: Must be "ti,sn65dsi86"
+- reg: i2c address of the chip, 0x2d as per datasheet
+- enable-gpios: gpio specification for bridge_en pin (active high)
+
+- vccio-supply: A 1.8V supply that powers up the digital IOs.
+- vpll-supply: A 1.8V supply that powers up the displayport PLL.
+- vcca-supply: A 1.2V supply that powers up the analog circuits.
+- vcc-supply: A 1.2V supply that powers up the digital core.
+
+Optional properties:
+- interrupts-extended: Specifier for the SN65DSI86 interrupt line.
+
+- gpio-controller: Marks the device has a GPIO controller.
+- #gpio-cells    : Should be two. The first cell is the pin number and
+                   the second cell is used to specify flags.
+                   See ../../gpio/gpio.txt for more information.
+- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description of
+               the cell formats.
+
+- clock-names: should be "refclk"
+- clocks: Specification for input reference clock. The reference
+	  clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz.
+
+- data-lanes: See ../../media/video-interface.txt
+- lane-polarities: See ../../media/video-interface.txt
+
+- suspend-gpios: specification for GPIO1 pin on bridge (active low)
+
+Required nodes:
+This device has two video ports. Their connections are modelled using the
+OF graph bindings specified in Documentation/devicetree/bindings/graph.txt.
+
+- Video port 0 for DSI input
+- Video port 1 for eDP output
+
+Example
+-------
+
+edp-bridge@2d {
+	compatible = "ti,sn65dsi86";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reg = <0x2d>;
+
+	enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>;
+	suspend-gpios = <&msmgpio 34 GPIO_ACTIVE_LOW>;
+
+	interrupts-extended = <&gpio3 4 IRQ_TYPE_EDGE_FALLING>;
+
+	vccio-supply = <&pm8916_l17>;
+	vcca-supply = <&pm8916_l6>;
+	vpll-supply = <&pm8916_l17>;
+	vcc-supply = <&pm8916_l6>;
+
+	clock-names = "refclk";
+	clocks = <&input_refclk>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			edp_bridge_in: endpoint {
+				remote-endpoint = <&dsi_out>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			edp_bridge_out: endpoint {
+				data-lanes = <2 1 3 0>;
+				lane-polarities = <0 1 0 1>;
+				remote-endpoint = <&edp_panel_in>;
+			};
+		};
+	};
+}

Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt

@@ -0,0 +1,35 @@
+TC358764 MIPI-DSI to LVDS panel bridge
+
+Required properties:
+  - compatible: "toshiba,tc358764"
+  - reg: the virtual channel number of a DSI peripheral
+  - vddc-supply: core voltage supply, 1.2V
+  - vddio-supply: I/O voltage supply, 1.8V or 3.3V
+  - vddlvds-supply: LVDS1/2 voltage supply, 3.3V
+  - reset-gpios: a GPIO spec for the reset pin
+
+The device node can contain following 'port' child nodes,
+according to the OF graph bindings defined in [1]:
+  0: DSI Input, not required, if the bridge is DSI controlled
+  1: LVDS Output, mandatory
+
+[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+	bridge@0 {
+		reg = <0>;
+		compatible = "toshiba,tc358764";
+		vddc-supply = <&vcc_1v2_reg>;
+		vddio-supply = <&vcc_1v8_reg>;
+		vddlvds-supply = <&vcc_3v3_reg>;
+		reset-gpios = <&gpd1 6 GPIO_ACTIVE_LOW>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		port@1 {
+			reg = <1>;
+			lvds_ep: endpoint {
+				remote-endpoint = <&panel_ep>;
+			};
+		};
+	};

Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt

@@ -21,6 +21,9 @@ Required properties:
   - samsung,pll-clock-frequency: specifies frequency of the oscillator clock
   - #address-cells, #size-cells: should be set respectively to <1> and <0>
     according to DSI host bindings (see MIPI DSI bindings [1])
+  - samsung,burst-clock-frequency: specifies DSI frequency in high-speed burst
+    mode
+  - samsung,esc-clock-frequency: specifies DSI frequency in escape mode
 
 Optional properties:
   - power-domains: a phandle to DSIM power domain node
@@ -29,25 +32,9 @@ Child nodes:
   Should contain DSI peripheral nodes (see MIPI DSI bindings [1]).
 
 Video interfaces:
-  Device node can contain video interface port nodes according to [2].
-  The following are properties specific to those nodes:
-
-  port node inbound:
-    - reg: (required) must be 0.
-  port node outbound:
-    - reg: (required) must be 1.
-
-  endpoint node connected from mic node (reg = 0):
-    - remote-endpoint: specifies the endpoint in mic node. This node is required
-		       for Exynos5433 mipi dsi. So mic can access to panel node
-		       throughout this dsi node.
-  endpoint node connected to panel node (reg = 1):
-    - remote-endpoint: specifies the endpoint in panel node. This node is
-		       required in all kinds of exynos mipi dsi to represent
-		       the connection between mipi dsi and panel.
-    - samsung,burst-clock-frequency: specifies DSI frequency in high-speed burst
-      mode
-    - samsung,esc-clock-frequency: specifies DSI frequency in escape mode
+  Device node can contain following video interface port nodes according to [2]:
+  0: RGB input,
+  1: DSI output
 
 [1]: Documentation/devicetree/bindings/display/mipi-dsi-bus.txt
 [2]: Documentation/devicetree/bindings/media/video-interfaces.txt