Merge tag 'mmc-fixes-for-3.3' of git://git.kernel.org/pub/scm/linux/k…

…ernel/git/cjb/mmc

MMC fixes from Chris Ball for 3.3:
 - atmel-mci: oops fix against regression introduced in 3.2
 - core: power saving regression fix against 3.3-rc1
 - core: suspend/resume fix for UHS-I cards
 - esdhc-imx: MMC card regression fix against 3.0
 - mmci: oops fix for ARM systems with large (64k) pages
 - MAINTAINERS update for atmel-mci.

* tag 'mmc-fixes-for-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
  mmc: core: Fixup suspend/resume issues for UHS-I cards
  mmc: mmci: reduce max_blk_count to avoid overflowing max_req_size
  mmc: sdhci-esdhc-imx: fix for mmc cards on i.MX5
  mmc: core: fix regression: set default clock gating delay to 0
  MAINTAINERS: hand over atmel-mci (sd/mmc interface)
  mmc: atmel-mci: don't use dma features when using DMA with no chan available

MAINTAINERS

@@ -1310,15 +1310,15 @@ F:	drivers/atm/
 F:	include/linux/atm*
 
 ATMEL AT91 MCI DRIVER
-M:	Nicolas Ferre <nicolas.ferre@atmel.com>
+M:	Ludovic Desroches <ludovic.desroches@atmel.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 W:	http://www.atmel.com/products/AT91/
 W:	http://www.at91.com/
 S:	Maintained
 F:	drivers/mmc/host/at91_mci.c
 
 ATMEL AT91 / AT32 MCI DRIVER
-M:	Nicolas Ferre <nicolas.ferre@atmel.com>
+M:	Ludovic Desroches <ludovic.desroches@atmel.com>
 S:	Maintained
 F:	drivers/mmc/host/atmel-mci.c
 F:	drivers/mmc/host/atmel-mci-regs.h

drivers/mmc/core/core.c

@@ -2068,6 +2068,9 @@ static int mmc_rescan_try_freq(struct mmc_host *host, unsigned freq)
 	 */
 	mmc_hw_reset_for_init(host);
 
+	/* Initialization should be done at 3.3 V I/O voltage. */
+	mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, 0);
+
 	/*
 	 * sdio_reset sends CMD52 to reset card.  Since we do not know
 	 * if the card is being re-initialized, just send it.  CMD52

drivers/mmc/core/host.c

@@ -238,10 +238,10 @@ static inline void mmc_host_clk_init(struct mmc_host *host)
 	/* Hold MCI clock for 8 cycles by default */
 	host->clk_delay = 8;
 	/*
-	 * Default clock gating delay is 200ms.
+	 * Default clock gating delay is 0ms to avoid wasting power.
 	 * This value can be tuned by writing into sysfs entry.
 	 */
-	host->clkgate_delay = 200;
+	host->clkgate_delay = 0;
 	host->clk_gated = false;
 	INIT_DELAYED_WORK(&host->clk_gate_work, mmc_host_clk_gate_work);
 	spin_lock_init(&host->clk_lock);

drivers/mmc/core/mmc.c

@@ -816,6 +816,9 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
 	if (!mmc_host_is_spi(host))
 		mmc_set_bus_mode(host, MMC_BUSMODE_OPENDRAIN);
 
+	/* Initialization should be done at 3.3 V I/O voltage. */
+	mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, 0);
+
 	/*
 	 * Since we're changing the OCR value, we seem to
 	 * need to tell some cards to go back to the idle

drivers/mmc/core/sd.c

@@ -911,6 +911,9 @@ static int mmc_sd_init_card(struct mmc_host *host, u32 ocr,
 	BUG_ON(!host);
 	WARN_ON(!host->claimed);
 
+	/* The initialization should be done at 3.3 V I/O voltage. */
+	mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, 0);
+
 	err = mmc_sd_get_cid(host, ocr, cid, &rocr);
 	if (err)
 		return err;
@@ -1156,11 +1159,6 @@ int mmc_attach_sd(struct mmc_host *host)
 	BUG_ON(!host);
 	WARN_ON(!host->claimed);
 
-	/* Make sure we are at 3.3V signalling voltage */
-	err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, false);
-	if (err)
-		return err;
-
 	/* Disable preset value enable if already set since last time */
 	if (host->ops->enable_preset_value) {
 		mmc_host_clk_hold(host);

drivers/mmc/core/sdio.c

@@ -585,6 +585,9 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr,
 	 * Inform the card of the voltage
 	 */
 	if (!powered_resume) {
+		/* The initialization should be done at 3.3 V I/O voltage. */
+		mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, 0);
+
 		err = mmc_send_io_op_cond(host, host->ocr, &ocr);
 		if (err)
 			goto err;
@@ -996,6 +999,11 @@ static int mmc_sdio_power_restore(struct mmc_host *host)
 	 * With these steps taken, mmc_select_voltage() is also required to
 	 * restore the correct voltage setting of the card.
 	 */
+
+	/* The initialization should be done at 3.3 V I/O voltage. */
+	if (!mmc_card_keep_power(host))
+		mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, 0);
+
 	sdio_reset(host);
 	mmc_go_idle(host);
 	mmc_send_if_cond(host, host->ocr_avail);

drivers/mmc/host/atmel-mci.c

@@ -1948,12 +1948,12 @@ static bool atmci_filter(struct dma_chan *chan, void *slave)
 	}
 }
 
-static void atmci_configure_dma(struct atmel_mci *host)
+static bool atmci_configure_dma(struct atmel_mci *host)
 {
 	struct mci_platform_data	*pdata;
 
 	if (host == NULL)
-		return;
+		return false;
 
 	pdata = host->pdev->dev.platform_data;
 
@@ -1970,12 +1970,15 @@ static void atmci_configure_dma(struct atmel_mci *host)
 		host->dma.chan =
 			dma_request_channel(mask, atmci_filter, pdata->dma_slave);
 	}
-	if (!host->dma.chan)
-		dev_notice(&host->pdev->dev, "DMA not available, using PIO\n");
-	else
+	if (!host->dma.chan) {
+		dev_warn(&host->pdev->dev, "no DMA channel available\n");
+		return false;
+	} else {
 		dev_info(&host->pdev->dev,
 					"Using %s for DMA transfers\n",
 					dma_chan_name(host->dma.chan));
+		return true;
+	}
 }
 
 static inline unsigned int atmci_get_version(struct atmel_mci *host)
@@ -2085,8 +2088,7 @@ static int __init atmci_probe(struct platform_device *pdev)
 
 	/* Get MCI capabilities and set operations according to it */
 	atmci_get_cap(host);
-	if (host->caps.has_dma) {
-		dev_info(&pdev->dev, "using DMA\n");
+	if (host->caps.has_dma && atmci_configure_dma(host)) {
 		host->prepare_data = &atmci_prepare_data_dma;
 		host->submit_data = &atmci_submit_data_dma;
 		host->stop_transfer = &atmci_stop_transfer_dma;
@@ -2096,15 +2098,12 @@ static int __init atmci_probe(struct platform_device *pdev)
 		host->submit_data = &atmci_submit_data_pdc;
 		host->stop_transfer = &atmci_stop_transfer_pdc;
 	} else {
-		dev_info(&pdev->dev, "no DMA, no PDC\n");
+		dev_info(&pdev->dev, "using PIO\n");
 		host->prepare_data = &atmci_prepare_data;
 		host->submit_data = &atmci_submit_data;
 		host->stop_transfer = &atmci_stop_transfer;
 	}
 
-	if (host->caps.has_dma)
-		atmci_configure_dma(host);
-
 	platform_set_drvdata(pdev, host);
 
 	/* We need at least one slot to succeed */

drivers/mmc/host/mmci.c

@@ -1271,12 +1271,13 @@ static int __devinit mmci_probe(struct amba_device *dev,
 	/*
 	 * Block size can be up to 2048 bytes, but must be a power of two.
 	 */
-	mmc->max_blk_size = 2048;
+	mmc->max_blk_size = 1 << 11;
 
 	/*
-	 * No limit on the number of blocks transferred.
+	 * Limit the number of blocks transferred so that we don't overflow
+	 * the maximum request size.
 	 */
-	mmc->max_blk_count = mmc->max_req_size;
+	mmc->max_blk_count = mmc->max_req_size >> 11;
 
 	spin_lock_init(&host->lock);
 

drivers/mmc/host/sdhci-esdhc-imx.c

@@ -269,8 +269,9 @@ static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
 		imx_data->scratchpad = val;
 		return;
 	case SDHCI_COMMAND:
-		if ((host->cmd->opcode == MMC_STOP_TRANSMISSION)
-			&& (imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
+		if ((host->cmd->opcode == MMC_STOP_TRANSMISSION ||
+		     host->cmd->opcode == MMC_SET_BLOCK_COUNT) &&
+	            (imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
 			val |= SDHCI_CMD_ABORTCMD;
 
 		if (is_imx6q_usdhc(imx_data)) {