Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel…

…/git/arm/arm-soc

Pull ARM SoC fixes from Arnd Bergmann:
 "This comes a bit later than I planned, and as a consequence is a
  larger than it should be.

  Most of the changes are devicetree fixes, across lots of platforms:
  Renesas, Samsung Exynos, Marvell EBU, TI OMAP, Rockchips, Amlogic
  Meson, Sigma Desings Tango, Allwinner SUNxi and TI Davinci.

  Also across many platforms, I applied an older series of simple
  randconfig build fixes. This includes making the CONFIG_MTD_XIP option
  compile again, which had been broken for many years and probably has
  not been missed, but it felt wrong to just remove it completely.

  The only other changes are:

   - We enable HWSPINLOCK in defconfig to get some Qualcomm boards to
     work out of the box.

   - A few regression fixes for Texas Instruments OMAP2+.

   - A boot regression fix for the Renesas regulator quirk.

   - A suspend/resume fix for Uniphier SoCs, fixing the resume of the
     system bus"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
  ARM: dts: tango4: Request RGMII RX and TX clock delays
  bus: uniphier-system-bus: set up registers when resuming
  ARM64: dts: marvell: armada-37xx: Fix the number of GPIO on south bridge
  ARM: shmobile: rcar-gen2: Fix deadlock in regulator quirk
  arm64: defconfig: enable missing HWSPINLOCK
  ARM: pxa: select both FB and FB_W100 for eseries
  ARM: ixp4xx: fix ioport_unmap definition
  ARM: ep93xx: use ARM_PATCH_PHYS_VIRT correctly
  ARM: mmp: mark usb_dma_mask as __maybe_unused
  ARM: omap2: mark unused functions as __maybe_unused
  ARM: omap1: avoid unused variable warning
  ARM: sirf: mark sirfsoc_init_late as __maybe_unused
  ARM: ixp4xx: use normal prototype for {read,write}s{b,w,l}
  ARM: omap1/ams-delta: warn about failed regulator enable
  ARM: rpc: rename RAM_SIZE macro
  ARM: w90x900: normalize clk API
  ARM: ep93xx: normalize clk API
  ARM: dts: sun8i: a83t: Switch to CCU device tree binding macros
  arm64: allwinner: sun50i-a64: Correct emac register size
  ARM: dts: sunxi: h3/h5: Correct emac register size
  ...

Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt

@@ -40,7 +40,7 @@ Optional properties:
 Example for a Mali-T760:
 
 gpu@ffa30000 {
-	compatible = "rockchip,rk3288-mali", "arm,mali-t760", "arm,mali-midgard";
+	compatible = "rockchip,rk3288-mali", "arm,mali-t760";
 	reg = <0xffa30000 0x10000>;
 	interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
 		     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,

arch/arm/Kconfig

@@ -380,7 +380,7 @@ config ARCH_EP93XX
 	bool "EP93xx-based"
 	select ARCH_HAS_HOLES_MEMORYMODEL
 	select ARM_AMBA
-	select ARM_PATCH_PHYS_VIRT
+	imply ARM_PATCH_PHYS_VIRT
 	select ARM_VIC
 	select AUTO_ZRELADDR
 	select CLKDEV_LOOKUP

arch/arm/boot/dts/armada-388-gp.dts

@@ -75,7 +75,7 @@
 					pinctrl-names = "default";
 					pinctrl-0 = <&pca0_pins>;
 					interrupt-parent = <&gpio0>;
-					interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+					interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
 					gpio-controller;
 					#gpio-cells = <2>;
 					interrupt-controller;
@@ -87,7 +87,7 @@
 					compatible = "nxp,pca9555";
 					pinctrl-names = "default";
 					interrupt-parent = <&gpio0>;
-					interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+					interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
 					gpio-controller;
 					#gpio-cells = <2>;
 					interrupt-controller;

arch/arm/boot/dts/da850-evm.dts

@@ -301,25 +301,4 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&vpif_capture_pins>, <&vpif_display_pins>;
 	status = "okay";
-
-	/* VPIF capture port */
-	port@0 {
-		vpif_input_ch0: endpoint@0 {
-			reg = <0>;
-			bus-width = <8>;
-		};
-
-		vpif_input_ch1: endpoint@1 {
-			reg = <1>;
-			bus-width = <8>;
-			data-shift = <8>;
-		};
-	};
-
-	/* VPIF display port */
-	port@1 {
-		vpif_output_ch0: endpoint {
-			bus-width = <8>;
-		};
-	};
 };

arch/arm/boot/dts/da850-lcdk.dts

@@ -318,11 +318,4 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&vpif_capture_pins>;
 	status = "okay";
-
-	/* VPIF capture port */
-	port {
-		vpif_ch0: endpoint {
-			  bus-width = <8>;
-		};
-	};
 };

arch/arm/boot/dts/dm8168-evm.dts

@@ -68,6 +68,34 @@
 			DM816X_IOPAD(0x0d08, MUX_MODE0)			/* USB1_DRVVBUS */
 		>;
 	};
+
+	nandflash_pins: nandflash_pins {
+		pinctrl-single,pins = <
+			DM816X_IOPAD(0x0b38, PULL_UP | MUX_MODE0)		/* PINCTRL207 GPMC_CS0*/
+			DM816X_IOPAD(0x0b60, PULL_ENA | MUX_MODE0)		/* PINCTRL217 GPMC_ADV_ALE */
+			DM816X_IOPAD(0x0b54, PULL_UP | PULL_ENA | MUX_MODE0)	/* PINCTRL214 GPMC_OE_RE */
+			DM816X_IOPAD(0x0b58, PULL_ENA | MUX_MODE0)		/* PINCTRL215 GPMC_BE0_CLE */
+			DM816X_IOPAD(0x0b50, PULL_UP | MUX_MODE0)		/* PINCTRL213 GPMC_WE */
+			DM816X_IOPAD(0x0b6c, MUX_MODE0)				/* PINCTRL220 GPMC_WAIT */
+			DM816X_IOPAD(0x0be4, PULL_ENA | MUX_MODE0)		/* PINCTRL250 GPMC_CLK */
+			DM816X_IOPAD(0x0ba4, MUX_MODE0)				/* PINCTRL234 GPMC_D0 */
+			DM816X_IOPAD(0x0ba8, MUX_MODE0)				/* PINCTRL234 GPMC_D1 */
+			DM816X_IOPAD(0x0bac, MUX_MODE0)				/* PINCTRL234 GPMC_D2 */
+			DM816X_IOPAD(0x0bb0, MUX_MODE0)				/* PINCTRL234 GPMC_D3 */
+			DM816X_IOPAD(0x0bb4, MUX_MODE0)				/* PINCTRL234 GPMC_D4 */
+			DM816X_IOPAD(0x0bb8, MUX_MODE0)				/* PINCTRL234 GPMC_D5 */
+			DM816X_IOPAD(0x0bbc, MUX_MODE0)				/* PINCTRL234 GPMC_D6 */
+			DM816X_IOPAD(0x0bc0, MUX_MODE0)				/* PINCTRL234 GPMC_D7 */
+			DM816X_IOPAD(0x0bc4, MUX_MODE0)				/* PINCTRL234 GPMC_D8 */
+			DM816X_IOPAD(0x0bc8, MUX_MODE0)				/* PINCTRL234 GPMC_D9 */
+			DM816X_IOPAD(0x0bcc, MUX_MODE0)				/* PINCTRL234 GPMC_D10 */
+			DM816X_IOPAD(0x0bd0, MUX_MODE0)				/* PINCTRL234 GPMC_D11 */
+			DM816X_IOPAD(0x0bd4, MUX_MODE0)				/* PINCTRL234 GPMC_D12 */
+			DM816X_IOPAD(0x0bd8, MUX_MODE0)				/* PINCTRL234 GPMC_D13 */
+			DM816X_IOPAD(0x0bdc, MUX_MODE0)				/* PINCTRL234 GPMC_D14 */
+			DM816X_IOPAD(0x0be0, MUX_MODE0)				/* PINCTRL234 GPMC_D15 */
+		>;
+	};
 };
 
 &i2c1 {
@@ -90,6 +118,8 @@
 
 &gpmc {
 	ranges = <0 0 0x04000000 0x01000000>;	/* CS0: 16MB for NAND */
+	pinctrl-names = "default";
+	pinctrl-0 = <&nandflash_pins>;
 
 	nand@0,0 {
 		compatible = "ti,omap2-nand";
@@ -98,9 +128,11 @@
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>; /* termcount */
+		rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ti,nand-ecc-opt = "bch8";
+		ti,elm-id = <&elm>;
 		nand-bus-width = <16>;
 		gpmc,device-width = <2>;
 		gpmc,sync-clk-ps = <0>;
@@ -164,7 +196,7 @@
 	vmmc-supply = <&vmmcsd_fixed>;
 	bus-width = <4>;
 	cd-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
 };
 
 /* At least dm8168-evm rev c won't support multipoint, later may */

arch/arm/boot/dts/dm816x.dtsi

@@ -145,7 +145,7 @@
 		};
 
 		elm: elm@48080000 {
-			compatible = "ti,816-elm";
+			compatible = "ti,am3352-elm";
 			ti,hwmods = "elm";
 			reg = <0x48080000 0x2000>;
 			interrupts = <4>;

arch/arm/boot/dts/dra71-evm.dts

@@ -190,15 +190,15 @@
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
 		ti,tx-internal-delay = <DP83867_RGMIIDCTL_250_PS>;
 		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>;
-		ti,impedance-control = <0x1f>;
+		ti,min-output-impedance;
 	};
 
 	dp83867_1: ethernet-phy@3 {
 		reg = <3>;
 		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
 		ti,tx-internal-delay = <DP83867_RGMIIDCTL_250_PS>;
 		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>;
-		ti,impedance-control = <0x1f>;
+		ti,min-output-impedance;
 	};
 };
 

arch/arm/boot/dts/exynos4.dtsi

@@ -59,6 +59,9 @@
 		compatible = "samsung,exynos4210-audss-clock";
 		reg = <0x03810000 0x0C>;
 		#clock-cells = <1>;
+		clocks = <&clock CLK_FIN_PLL>, <&clock CLK_FOUT_EPLL>,
+			 <&clock CLK_SCLK_AUDIO0>, <&clock CLK_SCLK_AUDIO0>;
+		clock-names = "pll_ref", "pll_in", "sclk_audio", "sclk_pcm_in";
 	};
 
 	i2s0: i2s@03830000 {

arch/arm/boot/dts/rk3288.dtsi

@@ -1126,8 +1126,8 @@
 		};
 	};
 
-	gpu: mali@ffa30000 {
-		compatible = "rockchip,rk3288-mali", "arm,mali-t760", "arm,mali-midgard";
+	gpu: gpu@ffa30000 {
+		compatible = "rockchip,rk3288-mali", "arm,mali-t760";
 		reg = <0xffa30000 0x10000>;
 		interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,

arch/arm/boot/dts/sun8i-a83t.dtsi

@@ -44,7 +44,9 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 
+#include <dt-bindings/clock/sun8i-a83t-ccu.h>
 #include <dt-bindings/clock/sun8i-r-ccu.h>
+#include <dt-bindings/reset/sun8i-a83t-ccu.h>
 
 / {
 	interrupt-parent = <&gic>;
@@ -175,8 +177,8 @@
 			compatible = "allwinner,sun8i-a83t-dma";
 			reg = <0x01c02000 0x1000>;
 			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu 21>;
-			resets = <&ccu 7>;
+			clocks = <&ccu CLK_BUS_DMA>;
+			resets = <&ccu RST_BUS_DMA>;
 			#dma-cells = <1>;
 		};
 
@@ -195,7 +197,7 @@
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
 			reg = <0x01c20800 0x400>;
-			clocks = <&ccu 45>, <&osc24M>, <&osc16Md512>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc16Md512>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			interrupt-controller;
@@ -247,8 +249,8 @@
 				     "allwinner,sun8i-h3-spdif";
 			reg = <0x01c21000 0x400>;
 			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu 44>, <&ccu 76>;
-			resets = <&ccu 32>;
+			clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
+			resets = <&ccu RST_BUS_SPDIF>;
 			clock-names = "apb", "spdif";
 			dmas = <&dma 2>;
 			dma-names = "tx";
@@ -263,8 +265,8 @@
 			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&ccu 53>;
-			resets = <&ccu 40>;
+			clocks = <&ccu CLK_BUS_UART0>;
+			resets = <&ccu RST_BUS_UART0>;
 			status = "disabled";
 		};
 

arch/arm/boot/dts/sunxi-h3-h5.dtsi

@@ -394,7 +394,7 @@
 		emac: ethernet@1c30000 {
 			compatible = "allwinner,sun8i-h3-emac";
 			syscon = <&syscon>;
-			reg = <0x01c30000 0x104>;
+			reg = <0x01c30000 0x10000>;
 			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
 			resets = <&ccu RST_BUS_EMAC>;

arch/arm/boot/dts/tango4-vantage-1172.dts

@@ -22,7 +22,7 @@
 };
 
 &eth0 {
-	phy-connection-type = "rgmii";
+	phy-connection-type = "rgmii-id";
 	phy-handle = <&eth0_phy>;
 	#address-cells = <1>;
 	#size-cells = <0>;

arch/arm/mach-davinci/board-da850-evm.c

@@ -1166,7 +1166,7 @@ static struct tvp514x_platform_data tvp5146_pdata = {
 
 #define TVP514X_STD_ALL (V4L2_STD_NTSC | V4L2_STD_PAL)
 
-static const struct vpif_input da850_ch0_inputs[] = {
+static struct vpif_input da850_ch0_inputs[] = {
 	{
 		.input = {
 			.index = 0,
@@ -1181,7 +1181,7 @@ static const struct vpif_input da850_ch0_inputs[] = {
 	},
 };
 
-static const struct vpif_input da850_ch1_inputs[] = {
+static struct vpif_input da850_ch1_inputs[] = {
 	{
 		.input = {
 			.index = 0,

arch/arm/mach-davinci/clock.c

@@ -218,6 +218,15 @@ int clk_set_parent(struct clk *clk, struct clk *parent)
 }
 EXPORT_SYMBOL(clk_set_parent);
 
+struct clk *clk_get_parent(struct clk *clk)
+{
+	if (!clk)
+		return NULL;
+
+	return clk->parent;
+}
+EXPORT_SYMBOL(clk_get_parent);
+
 int clk_register(struct clk *clk)
 {
 	if (clk == NULL || IS_ERR(clk))

arch/arm/mach-ep93xx/clock.c

@@ -475,6 +475,26 @@ int clk_set_rate(struct clk *clk, unsigned long rate)
 }
 EXPORT_SYMBOL(clk_set_rate);
 
+long clk_round_rate(struct clk *clk, unsigned long rate)
+{
+	WARN_ON(clk);
+	return 0;
+}
+EXPORT_SYMBOL(clk_round_rate);
+
+int clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	WARN_ON(clk);
+	return 0;
+}
+EXPORT_SYMBOL(clk_set_parent);
+
+struct clk *clk_get_parent(struct clk *clk)
+{
+	return clk->parent;
+}
+EXPORT_SYMBOL(clk_get_parent);
+
 
 static char fclk_divisors[] = { 1, 2, 4, 8, 16, 1, 1, 1 };
 static char hclk_divisors[] = { 1, 2, 4, 5, 6, 8, 16, 32 };