Merge branch 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/…

…git/gregkh/tty into for-next

Conflicts:
	arch/arm64/kernel/early_printk.c

Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt

@@ -0,0 +1,33 @@
+* NXP SC16IS7xx advanced Universal Asynchronous Receiver-Transmitter (UART)
+
+Required properties:
+- compatible: Should be one of the following:
+  - "nxp,sc16is740" for NXP SC16IS740,
+  - "nxp,sc16is741" for NXP SC16IS741,
+  - "nxp,sc16is750" for NXP SC16IS750,
+  - "nxp,sc16is752" for NXP SC16IS752,
+  - "nxp,sc16is760" for NXP SC16IS760,
+  - "nxp,sc16is762" for NXP SC16IS762.
+- reg: I2C address of the SC16IS7xx device.
+- interrupt-parent: The phandle for the interrupt controller that
+  services interrupts for this IC.
+- interrupts: Should contain the UART interrupt
+- clocks: Reference to the IC source clock.
+
+Optional properties:
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells: Should be two. The first cell is the GPIO number and
+  the second cell is used to specify the GPIO polarity:
+    0 = active high,
+    1 = active low.
+
+Example:
+        sc16is750: sc16is750@51 {
+                compatible = "nxp,sc16is750";
+                reg = <0x51>;
+                clocks = <&clk20m>;
+                interrupt-parent = <&gpio3>;
+                interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+                gpio-controller;
+                #gpio-cells = <2>;
+        };

Documentation/kernel-parameters.txt

@@ -883,6 +883,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 			which are not unmapped.
 
 	earlycon=	[KNL] Output early console device and options.
+
 		uart[8250],io,<addr>[,options]
 		uart[8250],mmio,<addr>[,options]
 		uart[8250],mmio32,<addr>[,options]
@@ -892,6 +893,14 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 			(mmio) or 32-bit (mmio32).
 			The options are the same as for ttyS, above.
 
+		pl011,<addr>
+			Start an early, polled-mode console on a pl011 serial
+			port at the specified address. The pl011 serial port
+			must already be setup and configured. Options are not
+			yet supported.
+
+		smh	Use ARM semihosting calls for early console.
+
 	earlyprintk=	[X86,SH,BLACKFIN,ARM]
 			earlyprintk=vga
 			earlyprintk=efi

arch/arm64/Kconfig

@@ -112,6 +112,9 @@ config IOMMU_HELPER
 config KERNEL_MODE_NEON
 	def_bool y
 
+config FIX_EARLYCON_MEM
+	def_bool y
+
 source "init/Kconfig"
 
 source "kernel/Kconfig.freezer"

arch/arm64/Kconfig.debug

@@ -20,15 +20,6 @@ config STRICT_DEVMEM
 
 	  If in doubt, say Y.
 
-config EARLY_PRINTK
-	bool "Early printk support"
-	default y
-	help
-	  Say Y here if you want to have an early console using the
-	  earlyprintk=<name>[,<addr>][,<options>] kernel parameter. It
-	  is assumed that the early console device has been initialised
-	  by the boot loader prior to starting the Linux kernel.
-
 config PID_IN_CONTEXTIDR
 	bool "Write the current PID to the CONTEXTIDR register"
 	help

arch/arm64/kernel/Makefile

@@ -18,7 +18,6 @@ arm64-obj-$(CONFIG_SMP)			+= smp.o smp_spin_table.o topology.o
 arm64-obj-$(CONFIG_PERF_EVENTS)		+= perf_regs.o
 arm64-obj-$(CONFIG_HW_PERF_EVENTS)	+= perf_event.o
 arm64-obj-$(CONFIG_HAVE_HW_BREAKPOINT)	+= hw_breakpoint.o
-arm64-obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
 arm64-obj-$(CONFIG_ARM64_CPU_SUSPEND)	+= sleep.o suspend.o
 arm64-obj-$(CONFIG_JUMP_LABEL)		+= jump_label.o
 arm64-obj-$(CONFIG_KGDB)		+= kgdb.o

arch/x86/Kconfig

@@ -261,6 +261,9 @@ config ARCH_HWEIGHT_CFLAGS
 config ARCH_SUPPORTS_UPROBES
 	def_bool y
 
+config FIX_EARLYCON_MEM
+	def_bool y
+
 source "init/Kconfig"
 source "kernel/Kconfig.freezer"
 

drivers/bluetooth/hci_ldisc.c

@@ -118,17 +118,29 @@ static inline struct sk_buff *hci_uart_dequeue(struct hci_uart *hu)
 
 int hci_uart_tx_wakeup(struct hci_uart *hu)
 {
-	struct tty_struct *tty = hu->tty;
-	struct hci_dev *hdev = hu->hdev;
-	struct sk_buff *skb;
-
 	if (test_and_set_bit(HCI_UART_SENDING, &hu->tx_state)) {
 		set_bit(HCI_UART_TX_WAKEUP, &hu->tx_state);
 		return 0;
 	}
 
 	BT_DBG("");
 
+	schedule_work(&hu->write_work);
+
+	return 0;
+}
+
+static void hci_uart_write_work(struct work_struct *work)
+{
+	struct hci_uart *hu = container_of(work, struct hci_uart, write_work);
+	struct tty_struct *tty = hu->tty;
+	struct hci_dev *hdev = hu->hdev;
+	struct sk_buff *skb;
+
+	/* REVISIT: should we cope with bad skbs or ->write() returning
+	 * and error value ?
+	 */
+
 restart:
 	clear_bit(HCI_UART_TX_WAKEUP, &hu->tx_state);
 
@@ -153,7 +165,6 @@ int hci_uart_tx_wakeup(struct hci_uart *hu)
 		goto restart;
 
 	clear_bit(HCI_UART_SENDING, &hu->tx_state);
-	return 0;
 }
 
 static void hci_uart_init_work(struct work_struct *work)
@@ -282,6 +293,7 @@ static int hci_uart_tty_open(struct tty_struct *tty)
 	tty->receive_room = 65536;
 
 	INIT_WORK(&hu->init_ready, hci_uart_init_work);
+	INIT_WORK(&hu->write_work, hci_uart_write_work);
 
 	spin_lock_init(&hu->rx_lock);
 
@@ -319,6 +331,8 @@ static void hci_uart_tty_close(struct tty_struct *tty)
 	if (hdev)
 		hci_uart_close(hdev);
 
+	cancel_work_sync(&hu->write_work);
+
 	if (test_and_clear_bit(HCI_UART_PROTO_SET, &hu->flags)) {
 		if (hdev) {
 			if (test_bit(HCI_UART_REGISTERED, &hu->flags))

drivers/bluetooth/hci_uart.h

@@ -68,6 +68,7 @@ struct hci_uart {
 	unsigned long		hdev_flags;
 
 	struct work_struct	init_ready;
+	struct work_struct	write_work;
 
 	struct hci_uart_proto	*proto;
 	void			*priv;

drivers/tty/serial/8250/8250_core.c

@@ -1926,13 +1926,8 @@ static void serial8250_put_poll_char(struct uart_port *port,
 	wait_for_xmitr(up, BOTH_EMPTY);
 	/*
 	 *	Send the character out.
-	 *	If a LF, also do CR...
 	 */
 	serial_port_out(port, UART_TX, c);
-	if (c == 10) {
-		wait_for_xmitr(up, BOTH_EMPTY);
-		serial_port_out(port, UART_TX, 13);
-	}
 
 	/*
 	 *	Finally, wait for transmitter to become empty