Revert "usb: pl2303: do not round to the next nearest standard baud r…

…ate for the divisor based baud rate encoding method"

This reverts commit 75417d9.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/serial/pl2303.c

@@ -273,46 +273,44 @@ static void pl2303_encode_baudrate(struct tty_struct *tty,
 					struct usb_serial_port *port,
 					u8 buf[4])
 {
+	const int baud_sup[] = { 75, 150, 300, 600, 1200, 1800, 2400, 3600,
+	                         4800, 7200, 9600, 14400, 19200, 28800, 38400,
+	                         57600, 115200, 230400, 460800, 500000, 614400,
+	                         921600, 1228800, 2457600, 3000000, 6000000 };
+
 	struct usb_serial *serial = port->serial;
 	struct pl2303_serial_private *spriv = usb_get_serial_data(serial);
 	int baud;
+	int i;
 
+	/*
+	 * NOTE: Only the values defined in baud_sup are supported!
+	 *       => if unsupported values are set, the PL2303 seems to use
+	 *          9600 baud (at least my PL2303X always does)
+	 */
 	baud = tty_get_baud_rate(tty);
 	dev_dbg(&port->dev, "baud requested = %d\n", baud);
 	if (!baud)
 		return;
 
-	if (spriv->type != HX || baud <= 115200) {
-		/*
-		 * NOTE: Only the values defined in baud_sup are supported !
-		 *       => if unsupported values are set, the PL2303 seems to
-		 *	    use 9600 baud (at least my PL2303X always does)
-		 */
-		const int baud_sup[] = { 75, 150, 300, 600, 1200, 1800, 2400,
-					 3600, 4800, 7200, 9600, 14400, 19200,
-					 28800, 38400, 57600, 115200, 230400,
-					 460800, 500000, 614400, 921600,
-					 1228800, 2457600, 3000000, 6000000 };
-		int i;
-
-		/* Set baudrate to nearest supported value */
-		for (i = 0; i < ARRAY_SIZE(baud_sup); ++i) {
-			if (baud_sup[i] > baud)
-				break;
-		}
+	/* Set baudrate to nearest supported value */
+	for (i = 0; i < ARRAY_SIZE(baud_sup); ++i) {
+		if (baud_sup[i] > baud)
+			break;
+	}
 
-		if (i == ARRAY_SIZE(baud_sup))
-			baud = baud_sup[i - 1];
-		else if (i > 0
-			     && (baud_sup[i] - baud) > (baud - baud_sup[i - 1]))
-			baud = baud_sup[i - 1];
-		else
-			baud = baud_sup[i];
+	if (i == ARRAY_SIZE(baud_sup))
+		baud = baud_sup[i - 1];
+	else if (i > 0 && (baud_sup[i] - baud) > (baud - baud_sup[i - 1]))
+		baud = baud_sup[i - 1];
+	else
+		baud = baud_sup[i];
 
-		/* type_0, type_1 only support up to 1228800 baud */
-		if (spriv->type != HX)
-			baud = min_t(int, baud, 1228800);
+	/* type_0, type_1 only support up to 1228800 baud */
+	if (spriv->type != HX)
+		baud = min_t(int, baud, 1228800);
 
+	if (spriv->type != HX || baud <= 115200) {
 		/* Direct (standard) baud rate encoding method */
 		put_unaligned_le32(baud, buf);
 	} else {
@@ -333,17 +331,10 @@ static void pl2303_encode_baudrate(struct tty_struct *tty,
 		 * => 8 < B < 16: device seems to work not properly
 		 * => B <= 8: device uses the max. value B = 512 instead
 		 */
-		unsigned int A, B;
 
-		/* Respect the specified baud rate limits */
-		baud = max_t(int, baud, 75);
-		if (spriv->type == HX)
-			baud = min_t(int, baud, 6000000);
-		else
-			baud = min_t(int, baud, 1228800);
 		/* Determine factors A and B */
-		A = 0;
-		B = 12000000 * 32 / baud;  /* 12MHz */
+		unsigned int A = 0;
+		unsigned int B = 12000000 * 32 / baud;  /* 12MHz */
 		B <<= 1; /* Add one bit for rounding */
 		while (B > (512 << 1) && A <= 14) {
 			A += 2;