Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upst…

…ream-linus

Pull MIPS updates from Ralf Baechle:
 "The whole series has been sitting in -next for quite a while with no
  complaints.  The last change to the series was before the weekend the
  removal of an SPI patch which Grant - even though previously acked by
  himself - appeared to raise objections.  So I removed it until the
  situation is clarified.  Other than that all the patches have the acks
  from their respective maintainers, all MIPS and x86 defconfigs are
  building fine and I'm not aware of any problems introduced by this
  series.

  Among the key features for this patch series is a sizable patchset for
  Lantiq which among other things introduces support for Lantiq's
  flagship product, the FALCON SOC.  It also means that the opensource
  developers behind this patchset have overtaken Lantiq's competing
  inhouse development team that was working behind closed doors.

  Less noteworthy the ath79 patchset which adds support for a few more
  chip variants, cleanups and fixes.  Finally the usual dose of tweaking
  of generic code."

Fix up trivial conflicts in arch/mips/lantiq/xway/gpio_{ebu,stp}.c where
printk spelling fixes clashed with file move and eventual removal of the
printk.

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (81 commits)
  MIPS: lantiq: remove orphaned code
  MIPS: Remove all -Wall and almost all -Werror usage from arch/mips.
  MIPS: lantiq: implement support for FALCON soc
  MTD: MIPS: lantiq: verify that the NOR interface is available on falcon soc
  MTD: MIPS: lantiq: implement OF support
  watchdog: MIPS: lantiq: implement OF support and minor fixes
  SERIAL: MIPS: lantiq: implement OF support
  GPIO: MIPS: lantiq: convert gpio-stp-xway to OF
  GPIO: MIPS: lantiq: convert gpio-mm-lantiq to OF and of_mm_gpio
  GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder
  MIPS: pci: convert lantiq driver to OF
  MIPS: lantiq: convert dma to platform driver
  MIPS: lantiq: implement support for clkdev api
  MIPS: lantiq: drop ltq_gpio_request() and gpio_to_irq()
  OF: MIPS: lantiq: implement irq_domain support
  OF: MIPS: lantiq: implement OF support
  MIPS: lantiq: drop mips_machine support
  OF: PCI: const usage needed by MIPS
  MIPS: Cavium: Remove smp_reserve_lock.
  MIPS: Move cache setup to setup_arch().
  ...

Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt

@@ -0,0 +1,38 @@
+Lantiq SoC External Bus memory mapped GPIO controller
+
+By attaching hardware latches to the EBU it is possible to create output
+only gpios. This driver configures a special memory address, which when
+written to outputs 16 bit to the latches.
+
+The node describing the memory mapped GPIOs needs to be a child of the node
+describing the "lantiq,localbus".
+
+Required properties:
+- compatible : Should be "lantiq,gpio-mm-lantiq"
+- reg : Address and length of the register set for the device
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify optional parameters (currently
+  unused).
+- gpio-controller : Marks the device node as a gpio controller.
+
+Optional properties:
+- lantiq,shadow : The default value that we shall assume as already set on the
+  shift register cascade.
+
+Example:
+
+localbus@0 {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	ranges = <0 0 0x0 0x3ffffff /* addrsel0 */
+		1 0 0x4000000 0x4000010>; /* addsel1 */
+	compatible = "lantiq,localbus", "simple-bus";
+
+	gpio_mm0: gpio@4000000 {
+		compatible = "lantiq,gpio-mm";
+		reg = <1 0x0 0x10>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		lantiq,shadow = <0x77f>
+	};
+}

Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt

@@ -0,0 +1,42 @@
+Lantiq SoC Serial To Parallel (STP) GPIO controller
+
+The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a
+peripheral controller used to drive external shift register cascades. At most
+3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem
+to drive the 2 LSBs of the cascade automatically.
+
+
+Required properties:
+- compatible : Should be "lantiq,gpio-stp-xway"
+- reg : Address and length of the register set for the device
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify optional parameters (currently
+  unused).
+- gpio-controller : Marks the device node as a gpio controller.
+
+Optional properties:
+- lantiq,shadow : The default value that we shall assume as already set on the
+  shift register cascade.
+- lantiq,groups : Set the 3 bit mask to select which of the 3 groups are enabled
+  in the shift register cascade.
+- lantiq,dsl : The dsl core can control the 2 LSBs of the gpio cascade. This 2 bit
+  property can enable this feature.
+- lantiq,phy1 : The gphy1 core can control 3 bits of the gpio cascade.
+- lantiq,phy2 : The gphy2 core can control 3 bits of the gpio cascade.
+- lantiq,rising : use rising instead of falling edge for the shift register
+
+Example:
+
+gpio1: stp@E100BB0 {
+	compatible = "lantiq,gpio-stp-xway";
+	reg = <0xE100BB0 0x40>;
+	#gpio-cells = <2>;
+	gpio-controller;
+
+	lantiq,shadow = <0xffff>;
+	lantiq,groups = <0x7>;
+	lantiq,dsl = <0x3>;
+	lantiq,phy1 = <0x7>;
+	lantiq,phy2 = <0x7>;
+	/* lantiq,rising; */
+};

arch/mips/Kconfig

@@ -233,8 +233,9 @@ config LANTIQ
 	select ARCH_REQUIRE_GPIOLIB
 	select SWAP_IO_SPACE
 	select BOOT_RAW
-	select HAVE_CLK
-	select MIPS_MACHINE
+	select HAVE_MACH_CLKDEV
+	select CLKDEV_LOOKUP
+	select USE_OF
 
 config LASAT
 	bool "LASAT Networks platforms"
@@ -1783,10 +1784,12 @@ endchoice
 
 config FORCE_MAX_ZONEORDER
 	int "Maximum zone order"
-	range 13 64 if SYS_SUPPORTS_HUGETLBFS && PAGE_SIZE_32KB
-	default "13" if SYS_SUPPORTS_HUGETLBFS && PAGE_SIZE_32KB
-	range 12 64 if SYS_SUPPORTS_HUGETLBFS && PAGE_SIZE_16KB
-	default "12" if SYS_SUPPORTS_HUGETLBFS && PAGE_SIZE_16KB
+	range 14 64 if HUGETLB_PAGE && PAGE_SIZE_64KB
+	default "14" if HUGETLB_PAGE && PAGE_SIZE_64KB
+	range 13 64 if HUGETLB_PAGE && PAGE_SIZE_32KB
+	default "13" if HUGETLB_PAGE && PAGE_SIZE_32KB
+	range 12 64 if HUGETLB_PAGE && PAGE_SIZE_16KB
+	default "12" if HUGETLB_PAGE && PAGE_SIZE_16KB
 	range 11 64
 	default "11"
 	help

arch/mips/alchemy/devboards/db1200.c

@@ -22,6 +22,7 @@
 #include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/init.h>
+#include <linux/module.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/leds.h>

arch/mips/ath79/Kconfig

@@ -26,6 +26,18 @@ config ATH79_MACH_AP81
 	  Say 'Y' here if you want your kernel to support the
 	  Atheros AP81 reference board.
 
+config ATH79_MACH_DB120
+	bool "Atheros DB120 reference board"
+	select SOC_AR934X
+	select ATH79_DEV_GPIO_BUTTONS
+	select ATH79_DEV_LEDS_GPIO
+	select ATH79_DEV_SPI
+	select ATH79_DEV_USB
+	select ATH79_DEV_WMAC
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  Atheros DB120 reference board.
+
 config ATH79_MACH_PB44
 	bool "Atheros PB44 reference board"
 	select SOC_AR71XX
@@ -52,12 +64,14 @@ endmenu
 config SOC_AR71XX
 	select USB_ARCH_HAS_EHCI
 	select USB_ARCH_HAS_OHCI
+	select HW_HAS_PCI
 	def_bool n
 
 config SOC_AR724X
 	select USB_ARCH_HAS_EHCI
 	select USB_ARCH_HAS_OHCI
 	select HW_HAS_PCI
+	select PCI_AR724X if PCI
 	def_bool n
 
 config SOC_AR913X
@@ -68,6 +82,15 @@ config SOC_AR933X
 	select USB_ARCH_HAS_EHCI
 	def_bool n
 
+config SOC_AR934X
+	select USB_ARCH_HAS_EHCI
+	select HW_HAS_PCI
+	select PCI_AR724X if PCI
+	def_bool n
+
+config PCI_AR724X
+	def_bool n
+
 config ATH79_DEV_GPIO_BUTTONS
 	def_bool n
 
@@ -81,7 +104,7 @@ config ATH79_DEV_USB
 	def_bool n
 
 config ATH79_DEV_WMAC
-	depends on (SOC_AR913X || SOC_AR933X)
+	depends on (SOC_AR913X || SOC_AR933X || SOC_AR934X)
 	def_bool n
 
 endif

arch/mips/ath79/Makefile

@@ -11,6 +11,7 @@
 obj-y	:= prom.o setup.o irq.o common.o clock.o gpio.o
 
 obj-$(CONFIG_EARLY_PRINTK)		+= early_printk.o
+obj-$(CONFIG_PCI)			+= pci.o
 
 #
 # Devices
@@ -27,5 +28,6 @@ obj-$(CONFIG_ATH79_DEV_WMAC)		+= dev-wmac.o
 #
 obj-$(CONFIG_ATH79_MACH_AP121)		+= mach-ap121.o
 obj-$(CONFIG_ATH79_MACH_AP81)		+= mach-ap81.o
+obj-$(CONFIG_ATH79_MACH_DB120)		+= mach-db120.o
 obj-$(CONFIG_ATH79_MACH_PB44)		+= mach-pb44.o
 obj-$(CONFIG_ATH79_MACH_UBNT_XM)	+= mach-ubnt-xm.o

arch/mips/ath79/clock.c

@@ -1,8 +1,11 @@
 /*
  *  Atheros AR71XX/AR724X/AR913X common routines
  *
+ *  Copyright (C) 2010-2011 Jaiganesh Narayanan <jnarayanan@atheros.com>
  *  Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
  *
+ *  Parts of this file are based on Atheros' 2.6.15/2.6.31 BSP
+ *
  *  This program is free software; you can redistribute it and/or modify it
  *  under the terms of the GNU General Public License version 2 as published
  *  by the Free Software Foundation.
@@ -163,6 +166,82 @@ static void __init ar933x_clocks_init(void)
 	ath79_uart_clk.rate = ath79_ref_clk.rate;
 }
 
+static void __init ar934x_clocks_init(void)
+{
+	u32 pll, out_div, ref_div, nint, frac, clk_ctrl, postdiv;
+	u32 cpu_pll, ddr_pll;
+	u32 bootstrap;
+
+	bootstrap = ath79_reset_rr(AR934X_RESET_REG_BOOTSTRAP);
+	if (bootstrap &	AR934X_BOOTSTRAP_REF_CLK_40)
+		ath79_ref_clk.rate = 40 * 1000 * 1000;
+	else
+		ath79_ref_clk.rate = 25 * 1000 * 1000;
+
+	pll = ath79_pll_rr(AR934X_PLL_CPU_CONFIG_REG);
+	out_div = (pll >> AR934X_PLL_CPU_CONFIG_OUTDIV_SHIFT) &
+		  AR934X_PLL_CPU_CONFIG_OUTDIV_MASK;
+	ref_div = (pll >> AR934X_PLL_CPU_CONFIG_REFDIV_SHIFT) &
+		  AR934X_PLL_CPU_CONFIG_REFDIV_MASK;
+	nint = (pll >> AR934X_PLL_CPU_CONFIG_NINT_SHIFT) &
+	       AR934X_PLL_CPU_CONFIG_NINT_MASK;
+	frac = (pll >> AR934X_PLL_CPU_CONFIG_NFRAC_SHIFT) &
+	       AR934X_PLL_CPU_CONFIG_NFRAC_MASK;
+
+	cpu_pll = nint * ath79_ref_clk.rate / ref_div;
+	cpu_pll += frac * ath79_ref_clk.rate / (ref_div * (2 << 6));
+	cpu_pll /= (1 << out_div);
+
+	pll = ath79_pll_rr(AR934X_PLL_DDR_CONFIG_REG);
+	out_div = (pll >> AR934X_PLL_DDR_CONFIG_OUTDIV_SHIFT) &
+		  AR934X_PLL_DDR_CONFIG_OUTDIV_MASK;
+	ref_div = (pll >> AR934X_PLL_DDR_CONFIG_REFDIV_SHIFT) &
+		  AR934X_PLL_DDR_CONFIG_REFDIV_MASK;
+	nint = (pll >> AR934X_PLL_DDR_CONFIG_NINT_SHIFT) &
+	       AR934X_PLL_DDR_CONFIG_NINT_MASK;
+	frac = (pll >> AR934X_PLL_DDR_CONFIG_NFRAC_SHIFT) &
+	       AR934X_PLL_DDR_CONFIG_NFRAC_MASK;
+
+	ddr_pll = nint * ath79_ref_clk.rate / ref_div;
+	ddr_pll += frac * ath79_ref_clk.rate / (ref_div * (2 << 10));
+	ddr_pll /= (1 << out_div);
+
+	clk_ctrl = ath79_pll_rr(AR934X_PLL_CPU_DDR_CLK_CTRL_REG);
+
+	postdiv = (clk_ctrl >> AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_POST_DIV_SHIFT) &
+		  AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_POST_DIV_MASK;
+
+	if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_PLL_BYPASS)
+		ath79_cpu_clk.rate = ath79_ref_clk.rate;
+	else if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_CPUCLK_FROM_CPUPLL)
+		ath79_cpu_clk.rate = cpu_pll / (postdiv + 1);
+	else
+		ath79_cpu_clk.rate = ddr_pll / (postdiv + 1);
+
+	postdiv = (clk_ctrl >> AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_POST_DIV_SHIFT) &
+		  AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_POST_DIV_MASK;
+
+	if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_PLL_BYPASS)
+		ath79_ddr_clk.rate = ath79_ref_clk.rate;
+	else if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_DDRCLK_FROM_DDRPLL)
+		ath79_ddr_clk.rate = ddr_pll / (postdiv + 1);
+	else
+		ath79_ddr_clk.rate = cpu_pll / (postdiv + 1);
+
+	postdiv = (clk_ctrl >> AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_POST_DIV_SHIFT) &
+		  AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_POST_DIV_MASK;
+
+	if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_PLL_BYPASS)
+		ath79_ahb_clk.rate = ath79_ref_clk.rate;
+	else if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_AHBCLK_FROM_DDRPLL)
+		ath79_ahb_clk.rate = ddr_pll / (postdiv + 1);
+	else
+		ath79_ahb_clk.rate = cpu_pll / (postdiv + 1);
+
+	ath79_wdt_clk.rate = ath79_ref_clk.rate;
+	ath79_uart_clk.rate = ath79_ref_clk.rate;
+}
+
 void __init ath79_clocks_init(void)
 {
 	if (soc_is_ar71xx())
@@ -173,6 +252,8 @@ void __init ath79_clocks_init(void)
 		ar913x_clocks_init();
 	else if (soc_is_ar933x())
 		ar933x_clocks_init();
+	else if (soc_is_ar934x())
+		ar934x_clocks_init();
 	else
 		BUG();
 

arch/mips/ath79/common.c

@@ -1,9 +1,12 @@
 /*
  *  Atheros AR71XX/AR724X/AR913X common routines
  *
- *  Copyright (C) 2008-2010 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2010-2011 Jaiganesh Narayanan <jnarayanan@atheros.com>
+ *  Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
  *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
  *
+ *  Parts of this file are based on Atheros' 2.6.15/2.6.31 BSP
+ *
  *  This program is free software; you can redistribute it and/or modify it
  *  under the terms of the GNU General Public License version 2 as published
  *  by the Free Software Foundation.
@@ -67,6 +70,8 @@ void ath79_device_reset_set(u32 mask)
 		reg = AR913X_RESET_REG_RESET_MODULE;
 	else if (soc_is_ar933x())
 		reg = AR933X_RESET_REG_RESET_MODULE;
+	else if (soc_is_ar934x())
+		reg = AR934X_RESET_REG_RESET_MODULE;
 	else
 		BUG();
 
@@ -91,6 +96,8 @@ void ath79_device_reset_clear(u32 mask)
 		reg = AR913X_RESET_REG_RESET_MODULE;
 	else if (soc_is_ar933x())
 		reg = AR933X_RESET_REG_RESET_MODULE;
+	else if (soc_is_ar934x())
+		reg = AR934X_RESET_REG_RESET_MODULE;
 	else
 		BUG();
 

arch/mips/ath79/dev-common.c

@@ -89,7 +89,8 @@ void __init ath79_register_uart(void)
 
 	if (soc_is_ar71xx() ||
 	    soc_is_ar724x() ||
-	    soc_is_ar913x()) {
+	    soc_is_ar913x() ||
+	    soc_is_ar934x()) {
 		ath79_uart_data[0].uartclk = clk_get_rate(clk);
 		platform_device_register(&ath79_uart_device);
 	} else if (soc_is_ar933x()) {

arch/mips/ath79/dev-gpio-buttons.c

@@ -25,12 +25,10 @@ void __init ath79_register_gpio_keys_polled(int id,
 	struct gpio_keys_button *p;
 	int err;
 
-	p = kmalloc(nbuttons * sizeof(*p), GFP_KERNEL);
+	p = kmemdup(buttons, nbuttons * sizeof(*p), GFP_KERNEL);
 	if (!p)
 		return;
 
-	memcpy(p, buttons, nbuttons * sizeof(*p));
-
 	pdev = platform_device_alloc("gpio-keys-polled", id);
 	if (!pdev)
 		goto err_free_buttons;

arch/mips/ath79/dev-leds-gpio.c

@@ -24,12 +24,10 @@ void __init ath79_register_leds_gpio(int id,
 	struct gpio_led *p;
 	int err;
 
-	p = kmalloc(num_leds * sizeof(*p), GFP_KERNEL);
+	p = kmemdup(leds, num_leds * sizeof(*p), GFP_KERNEL);
 	if (!p)
 		return;
 
-	memcpy(p, leds, num_leds * sizeof(*p));
-
 	pdev = platform_device_alloc("leds-gpio", id);
 	if (!pdev)
 		goto err_free_leds;