Merge branch 'linus' into x86/x2apic

Conflicts:

	arch/x86/kernel/genapic_64.c

Manual merge:

	arch/x86/kernel/genx2apic_uv_x.c

Signed-off-by: Ingo Molnar <mingo@elte.hu>

Documentation/00-INDEX

@@ -89,8 +89,6 @@ cciss.txt
 	- info, major/minor #'s for Compaq's SMART Array Controllers.
 cdrom/
 	- directory with information on the CD-ROM drivers that Linux has.
-cli-sti-removal.txt
-	- cli()/sti() removal guide.
 computone.txt
 	- info on Computone Intelliport II/Plus Multiport Serial Driver.
 connector/
@@ -361,8 +359,6 @@ telephony/
 	- directory with info on telephony (e.g. voice over IP) support.
 time_interpolators.txt
 	- info on time interpolators.
-tipar.txt
-	- information about Parallel link cable for Texas Instruments handhelds.
 tty.txt
 	- guide to the locking policies of the tty layer.
 uml/

Documentation/ABI/testing/sysfs-class-regulator

@@ -0,0 +1,315 @@
+What:		/sys/class/regulator/.../state
+Date:		April 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		state. This holds the regulator output state.
+
+		This will be one of the following strings:
+
+		'enabled'
+		'disabled'
+		'unknown'
+
+		'enabled' means the regulator output is ON and is supplying
+		power to the system.
+
+		'disabled' means the regulator output is OFF and is not
+		supplying power to the system..
+
+		'unknown' means software cannot determine the state.
+
+		NOTE: this field can be used in conjunction with microvolts
+		and microamps to determine regulator output levels.
+
+
+What:		/sys/class/regulator/.../type
+Date:		April 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		type. This holds the regulator type.
+
+		This will be one of the following strings:
+
+		'voltage'
+		'current'
+		'unknown'
+
+		'voltage' means the regulator output voltage can be controlled
+		by software.
+
+		'current' means the regulator output current limit can be
+		controlled by software.
+
+		'unknown' means software cannot control either voltage or
+		current limit.
+
+
+What:		/sys/class/regulator/.../microvolts
+Date:		April 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		microvolts. This holds the regulator output voltage setting
+		measured in microvolts (i.e. E-6 Volts).
+
+		NOTE: This value should not be used to determine the regulator
+		output voltage level as this value is the same regardless of
+		whether the regulator is enabled or disabled.
+
+
+What:		/sys/class/regulator/.../microamps
+Date:		April 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		microamps. This holds the regulator output current limit
+		setting measured in microamps (i.e. E-6 Amps).
+
+		NOTE: This value should not be used to determine the regulator
+		output current level as this value is the same regardless of
+		whether the regulator is enabled or disabled.
+
+
+What:		/sys/class/regulator/.../opmode
+Date:		April 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		opmode. This holds the regulator operating mode setting.
+
+		The opmode value can be one of the following strings:
+
+		'fast'
+		'normal'
+		'idle'
+		'standby'
+		'unknown'
+
+		The modes are described in include/linux/regulator/regulator.h
+
+		NOTE: This value should not be used to determine the regulator
+		output operating mode as this value is the same regardless of
+		whether the regulator is enabled or disabled.
+
+
+What:		/sys/class/regulator/.../min_microvolts
+Date:		April 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		min_microvolts. This holds the minimum safe working regulator
+		output voltage setting for this domain measured in microvolts.
+
+		NOTE: this will return the string 'constraint not defined' if
+		the power domain has no min microvolts constraint defined by
+		platform code.
+
+
+What:		/sys/class/regulator/.../max_microvolts
+Date:		April 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		max_microvolts. This holds the maximum safe working regulator
+		output voltage setting for this domain measured in microvolts.
+
+		NOTE: this will return the string 'constraint not defined' if
+		the power domain has no max microvolts constraint defined by
+		platform code.
+
+
+What:		/sys/class/regulator/.../min_microamps
+Date:		April 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		min_microamps. This holds the minimum safe working regulator
+		output current limit setting for this domain measured in
+		microamps.
+
+		NOTE: this will return the string 'constraint not defined' if
+		the power domain has no min microamps constraint defined by
+		platform code.
+
+
+What:		/sys/class/regulator/.../max_microamps
+Date:		April 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		max_microamps. This holds the maximum safe working regulator
+		output current limit setting for this domain measured in
+		microamps.
+
+		NOTE: this will return the string 'constraint not defined' if
+		the power domain has no max microamps constraint defined by
+		platform code.
+
+
+What:		/sys/class/regulator/.../num_users
+Date:		April 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		num_users. This holds the number of consumer devices that
+		have called regulator_enable() on this regulator.
+
+
+What:		/sys/class/regulator/.../requested_microamps
+Date:		April 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		requested_microamps. This holds the total requested load
+		current in microamps for this regulator from all its consumer
+		devices.
+
+
+What:		/sys/class/regulator/.../parent
+Date:		April 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Some regulator directories will contain a link called parent.
+		This points to the parent or supply regulator if one exists.
+
+What:		/sys/class/regulator/.../suspend_mem_microvolts
+Date:		May 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		suspend_mem_microvolts. This holds the regulator output
+		voltage setting for this domain measured in microvolts when
+		the system is suspended to memory.
+
+		NOTE: this will return the string 'not defined' if
+		the power domain has no suspend to memory voltage defined by
+		platform code.
+
+What:		/sys/class/regulator/.../suspend_disk_microvolts
+Date:		May 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		suspend_disk_microvolts. This holds the regulator output
+		voltage setting for this domain measured in microvolts when
+		the system is suspended to disk.
+
+		NOTE: this will return the string 'not defined' if
+		the power domain has no suspend to disk voltage defined by
+		platform code.
+
+What:		/sys/class/regulator/.../suspend_standby_microvolts
+Date:		May 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		suspend_standby_microvolts. This holds the regulator output
+		voltage setting for this domain measured in microvolts when
+		the system is suspended to standby.
+
+		NOTE: this will return the string 'not defined' if
+		the power domain has no suspend to standby voltage defined by
+		platform code.
+
+What:		/sys/class/regulator/.../suspend_mem_mode
+Date:		May 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		suspend_mem_mode. This holds the regulator operating mode
+		setting for this domain when the system is suspended to
+		memory.
+
+		NOTE: this will return the string 'not defined' if
+		the power domain has no suspend to memory mode defined by
+		platform code.
+
+What:		/sys/class/regulator/.../suspend_disk_mode
+Date:		May 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		suspend_disk_mode. This holds the regulator operating mode
+		setting for this domain when the system is suspended to disk.
+
+		NOTE: this will return the string 'not defined' if
+		the power domain has no suspend to disk mode defined by
+		platform code.
+
+What:		/sys/class/regulator/.../suspend_standby_mode
+Date:		May 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		suspend_standby_mode. This holds the regulator operating mode
+		setting for this domain when the system is suspended to
+		standby.
+
+		NOTE: this will return the string 'not defined' if
+		the power domain has no suspend to standby mode defined by
+		platform code.
+
+What:		/sys/class/regulator/.../suspend_mem_state
+Date:		May 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		suspend_mem_state. This holds the regulator operating state
+		when suspended to memory.
+
+		This will be one of the following strings:
+
+		'enabled'
+		'disabled'
+		'not defined'
+
+What:		/sys/class/regulator/.../suspend_disk_state
+Date:		May 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		suspend_disk_state. This holds the regulator operating state
+		when suspended to disk.
+
+		This will be one of the following strings:
+
+		'enabled'
+		'disabled'
+		'not defined'
+
+What:		/sys/class/regulator/.../suspend_standby_state
+Date:		May 2008
+KernelVersion:	2.6.26
+Contact:	Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+		Each regulator directory will contain a field called
+		suspend_standby_state. This holds the regulator operating
+		state when suspended to standby.
+
+		This will be one of the following strings:
+
+		'enabled'
+		'disabled'
+		'not defined'

Documentation/CodingStyle

@@ -474,25 +474,29 @@ make a good program).
 So, you can either get rid of GNU emacs, or change it to use saner
 values.  To do the latter, you can stick the following in your .emacs file:
 
-(defun linux-c-mode ()
-  "C mode with adjusted defaults for use with the Linux kernel."
-  (interactive)
-  (c-mode)
-  (c-set-style "K&R")
-  (setq tab-width 8)
-  (setq indent-tabs-mode t)
-  (setq c-basic-offset 8))
-
-This will define the M-x linux-c-mode command.  When hacking on a
-module, if you put the string -*- linux-c -*- somewhere on the first
-two lines, this mode will be automatically invoked. Also, you may want
-to add
-
-(setq auto-mode-alist (cons '("/usr/src/linux.*/.*\\.[ch]$" . linux-c-mode)
-			auto-mode-alist))
-
-to your .emacs file if you want to have linux-c-mode switched on
-automagically when you edit source files under /usr/src/linux.
+(defun c-lineup-arglist-tabs-only (ignored)
+  "Line up argument lists by tabs, not spaces"
+  (let* ((anchor (c-langelem-pos c-syntactic-element))
+	 (column (c-langelem-2nd-pos c-syntactic-element))
+	 (offset (- (1+ column) anchor))
+	 (steps (floor offset c-basic-offset)))
+    (* (max steps 1)
+       c-basic-offset)))
+
+(add-hook 'c-mode-hook
+          (lambda ()
+            (let ((filename (buffer-file-name)))
+              ;; Enable kernel mode for the appropriate files
+              (when (and filename
+                         (string-match "~/src/linux-trees" filename))
+                (setq indent-tabs-mode t)
+                (c-set-style "linux")
+                (c-set-offset 'arglist-cont-nonempty
+                              '(c-lineup-gcc-asm-reg
+                                c-lineup-arglist-tabs-only))))))
+
+This will make emacs go better with the kernel coding style for C
+files below ~/src/linux-trees.
 
 But even if you fail in getting emacs to do sane formatting, not
 everything is lost: use "indent".

Documentation/DMA-API.txt

@@ -298,10 +298,10 @@ recommended that you never use these unless you really know what the
 cache width is.
 
 int
-dma_mapping_error(dma_addr_t dma_addr)
+dma_mapping_error(struct device *dev, dma_addr_t dma_addr)
 
 int
-pci_dma_mapping_error(dma_addr_t dma_addr)
+pci_dma_mapping_error(struct pci_dev *hwdev, dma_addr_t dma_addr)
 
 In some circumstances dma_map_single and dma_map_page will fail to create
 a mapping. A driver can check for these errors by testing the returned