Merge branch 'qca7000_spi'

Stefan Wahren says:

====================
add Qualcomm QCA7000 ethernet driver

This patch series adds support for the Qualcomm QCA7000 Homeplug GreenPHY.
The QCA7000 is serial-to-powerline bridge with two interfaces: UART and SPI.
These patches handles only the last one, with an Ethernet over SPI protocol
driver.

This driver based on the Qualcomm code [1], but contains a lot of changes
since last year:

* devicetree support
* DebugFS support
* ethtool support
* better error handling
* performance improvements
* code cleanup
* some bugfixes

The code has been tested only on Freescale i.MX28 boards, but should work
on other platforms.

[1] - https://github.com/IoE/qca7000

Changes in V3:
- Use ether_addr_copy instead of memcpy
- Remove qcaspi_set_mac_address
- Improve DT parsing
- replace OF_GPIO dependancy with OF
- fix compile error caused by SET_ETHTOOL_OPS
- fix possible endless loop when spi read fails
- fix DT documentation
- fix coding style
- fix sparse warnings

Changes in V2:
- replace in DT the SPI intr GPIO with pure interrupt
- make legacy mode a boolean DT property and remove it as module parameter
- make burst length a module parameter instead of DT property
- make pluggable a module parameter instead of DT property
- improve DT documentation
- replace debugFS register dump with ethtool function
- replace debugFS stats with ethtool function
- implement function to get ring parameter via ethtool
- implement function to set TX ring count via ethtool
- fix TX ring state in debugFS
- optimize tx ring flush
- add byte limit for TX ring to avoid bufferbloat
- fix TX queue full and write buffer miss counter
- fix SPI clk speed module parameter
- fix possible packet loss
- fix possible race during transmit
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/qca-qca7000-spi.txt

@@ -0,0 +1,47 @@
+* Qualcomm QCA7000 (Ethernet over SPI protocol)
+
+Note: The QCA7000 is useable as a SPI device. In this case it must be defined
+as a child of a SPI master in the device tree.
+
+Required properties:
+- compatible : Should be "qca,qca7000"
+- reg : Should specify the SPI chip select
+- interrupts : The first cell should specify the index of the source interrupt
+  and the second cell should specify the trigger type as rising edge
+- spi-cpha : Must be set
+- spi-cpol: Must be set
+
+Optional properties:
+- interrupt-parent : Specify the pHandle of the source interrupt
+- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at.
+  Numbers smaller than 1000000 or greater than 16000000 are invalid. Missing
+  the property will set the SPI frequency to 8000000 Hertz.
+- local-mac-address: 6 bytes, MAC address
+- qca,legacy-mode : Set the SPI data transfer of the QCA7000 to legacy mode.
+  In this mode the SPI master must toggle the chip select between each data
+  word. In burst mode these gaps aren't necessary, which is faster.
+  This setting depends on how the QCA7000 is setup via GPIO pin strapping.
+  If the property is missing the driver defaults to burst mode.
+
+Example:
+
+/* Freescale i.MX28 SPI master*/
+ssp2: spi@80014000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+
+	qca7000: ethernet@0 {
+		compatible = "qca,qca7000";
+		reg = <0x0>;
+		interrupt-parent = <&gpio3>;      /* GPIO Bank 3 */
+		interrupts = <25 0x1>;            /* Index: 25, rising edge */
+		spi-cpha;                         /* SPI mode: CPHA=1 */
+		spi-cpol;                         /* SPI mode: CPOL=1 */
+		spi-max-frequency = <8000000>;    /* freq: 8 MHz */
+		local-mac-address = [ A0 B0 C0 D0 E0 F0 ];
+	};
+};

drivers/net/ethernet/Kconfig

@@ -150,6 +150,7 @@ config ETHOC
 source "drivers/net/ethernet/packetengines/Kconfig"
 source "drivers/net/ethernet/pasemi/Kconfig"
 source "drivers/net/ethernet/qlogic/Kconfig"
+source "drivers/net/ethernet/qualcomm/Kconfig"
 source "drivers/net/ethernet/realtek/Kconfig"
 source "drivers/net/ethernet/renesas/Kconfig"
 source "drivers/net/ethernet/rdc/Kconfig"

drivers/net/ethernet/Makefile

@@ -60,6 +60,7 @@ obj-$(CONFIG_ETHOC) += ethoc.o
 obj-$(CONFIG_NET_PACKET_ENGINE) += packetengines/
 obj-$(CONFIG_NET_VENDOR_PASEMI) += pasemi/
 obj-$(CONFIG_NET_VENDOR_QLOGIC) += qlogic/
+obj-$(CONFIG_NET_VENDOR_QUALCOMM) += qualcomm/
 obj-$(CONFIG_NET_VENDOR_REALTEK) += realtek/
 obj-$(CONFIG_SH_ETH) += renesas/
 obj-$(CONFIG_NET_VENDOR_RDC) += rdc/

drivers/net/ethernet/qualcomm/Kconfig

@@ -0,0 +1,30 @@
+#
+# Qualcomm network device configuration
+#
+
+config NET_VENDOR_QUALCOMM
+	bool "Qualcomm devices"
+	default y
+	depends on SPI_MASTER && OF_GPIO
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Qualcomm cards. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_QUALCOMM
+
+config QCA7000
+	tristate "Qualcomm Atheros QCA7000 support"
+	depends on SPI_MASTER && OF_GPIO
+	---help---
+	  This SPI protocol driver supports the Qualcomm Atheros QCA7000.
+
+	  To compile this driver as a module, choose M here. The module
+	  will be called qcaspi.
+
+endif # NET_VENDOR_QUALCOMM

drivers/net/ethernet/qualcomm/Makefile

@@ -0,0 +1,6 @@
+#
+# Makefile for the Qualcomm network device drivers.
+#
+
+obj-$(CONFIG_QCA7000) += qcaspi.o
+qcaspi-objs := qca_spi.o qca_framing.o qca_7k.o qca_debug.o

drivers/net/ethernet/qualcomm/qca_7k.c

@@ -0,0 +1,149 @@
+/*
+ *
+ *   Copyright (c) 2011, 2012, Qualcomm Atheros Communications Inc.
+ *   Copyright (c) 2014, I2SE GmbH
+ *
+ *   Permission to use, copy, modify, and/or distribute this software
+ *   for any purpose with or without fee is hereby granted, provided
+ *   that the above copyright notice and this permission notice appear
+ *   in all copies.
+ *
+ *   THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
+ *   WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
+ *   WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL
+ *   THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR
+ *   CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
+ *   LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
+ *   NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
+ *   CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+/*   This module implements the Qualcomm Atheros SPI protocol for
+ *   kernel-based SPI device.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/spi/spi.h>
+#include <linux/version.h>
+
+#include "qca_7k.h"
+
+void
+qcaspi_spi_error(struct qcaspi *qca)
+{
+	if (qca->sync != QCASPI_SYNC_READY)
+		return;
+
+	netdev_err(qca->net_dev, "spi error\n");
+	qca->sync = QCASPI_SYNC_UNKNOWN;
+	qca->stats.spi_err++;
+}
+
+int
+qcaspi_read_register(struct qcaspi *qca, u16 reg, u16 *result)
+{
+	__be16 rx_data;
+	__be16 tx_data;
+	struct spi_transfer *transfer;
+	struct spi_message *msg;
+	int ret;
+
+	tx_data = cpu_to_be16(QCA7K_SPI_READ | QCA7K_SPI_INTERNAL | reg);
+
+	if (qca->legacy_mode) {
+		msg = &qca->spi_msg1;
+		transfer = &qca->spi_xfer1;
+		transfer->tx_buf = &tx_data;
+		transfer->rx_buf = NULL;
+		transfer->len = QCASPI_CMD_LEN;
+		spi_sync(qca->spi_dev, msg);
+	} else {
+		msg = &qca->spi_msg2;
+		transfer = &qca->spi_xfer2[0];
+		transfer->tx_buf = &tx_data;
+		transfer->rx_buf = NULL;
+		transfer->len = QCASPI_CMD_LEN;
+		transfer = &qca->spi_xfer2[1];
+	}
+	transfer->tx_buf = NULL;
+	transfer->rx_buf = &rx_data;
+	transfer->len = QCASPI_CMD_LEN;
+	ret = spi_sync(qca->spi_dev, msg);
+
+	if (!ret)
+		ret = msg->status;
+
+	if (ret)
+		qcaspi_spi_error(qca);
+	else
+		*result = be16_to_cpu(rx_data);
+
+	return ret;
+}
+
+int
+qcaspi_write_register(struct qcaspi *qca, u16 reg, u16 value)
+{
+	__be16 tx_data[2];
+	struct spi_transfer *transfer;
+	struct spi_message *msg;
+	int ret;
+
+	tx_data[0] = cpu_to_be16(QCA7K_SPI_WRITE | QCA7K_SPI_INTERNAL | reg);
+	tx_data[1] = cpu_to_be16(value);
+
+	if (qca->legacy_mode) {
+		msg = &qca->spi_msg1;
+		transfer = &qca->spi_xfer1;
+		transfer->tx_buf = &tx_data[0];
+		transfer->rx_buf = NULL;
+		transfer->len = QCASPI_CMD_LEN;
+		spi_sync(qca->spi_dev, msg);
+	} else {
+		msg = &qca->spi_msg2;
+		transfer = &qca->spi_xfer2[0];
+		transfer->tx_buf = &tx_data[0];
+		transfer->rx_buf = NULL;
+		transfer->len = QCASPI_CMD_LEN;
+		transfer = &qca->spi_xfer2[1];
+	}
+	transfer->tx_buf = &tx_data[1];
+	transfer->rx_buf = NULL;
+	transfer->len = QCASPI_CMD_LEN;
+	ret = spi_sync(qca->spi_dev, msg);
+
+	if (!ret)
+		ret = msg->status;
+
+	if (ret)
+		qcaspi_spi_error(qca);
+
+	return ret;
+}
+
+int
+qcaspi_tx_cmd(struct qcaspi *qca, u16 cmd)
+{
+	__be16 tx_data;
+	struct spi_message *msg = &qca->spi_msg1;
+	struct spi_transfer *transfer = &qca->spi_xfer1;
+	int ret;
+
+	tx_data = cpu_to_be16(cmd);
+	transfer->len = sizeof(tx_data);
+	transfer->tx_buf = &tx_data;
+	transfer->rx_buf = NULL;
+
+	ret = spi_sync(qca->spi_dev, msg);
+
+	if (!ret)
+		ret = msg->status;
+
+	if (ret)
+		qcaspi_spi_error(qca);
+
+	return ret;
+}

drivers/net/ethernet/qualcomm/qca_7k.h

@@ -0,0 +1,72 @@
+/*
+ *   Copyright (c) 2011, 2012, Qualcomm Atheros Communications Inc.
+ *   Copyright (c) 2014, I2SE GmbH
+ *
+ *   Permission to use, copy, modify, and/or distribute this software
+ *   for any purpose with or without fee is hereby granted, provided
+ *   that the above copyright notice and this permission notice appear
+ *   in all copies.
+ *
+ *   THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
+ *   WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
+ *   WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL
+ *   THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR
+ *   CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM
+ *   LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
+ *   NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
+ *   CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+/*   Qualcomm Atheros SPI register definition.
+ *
+ *   This module is designed to define the Qualcomm Atheros SPI
+ *   register placeholders.
+ */
+
+#ifndef _QCA_7K_H
+#define _QCA_7K_H
+
+#include <linux/types.h>
+
+#include "qca_spi.h"
+
+#define QCA7K_SPI_READ     (1 << 15)
+#define QCA7K_SPI_WRITE    (0 << 15)
+#define QCA7K_SPI_INTERNAL (1 << 14)
+#define QCA7K_SPI_EXTERNAL (0 << 14)
+
+#define QCASPI_CMD_LEN    2
+#define QCASPI_HW_PKT_LEN 4
+#define QCASPI_HW_BUF_LEN 0xC5B
+
+/*   SPI registers;                               */
+#define SPI_REG_BFR_SIZE        0x0100
+#define SPI_REG_WRBUF_SPC_AVA   0x0200
+#define SPI_REG_RDBUF_BYTE_AVA  0x0300
+#define SPI_REG_SPI_CONFIG      0x0400
+#define SPI_REG_SPI_STATUS      0x0500
+#define SPI_REG_INTR_CAUSE      0x0C00
+#define SPI_REG_INTR_ENABLE     0x0D00
+#define SPI_REG_RDBUF_WATERMARK 0x1200
+#define SPI_REG_WRBUF_WATERMARK 0x1300
+#define SPI_REG_SIGNATURE       0x1A00
+#define SPI_REG_ACTION_CTRL     0x1B00
+
+/*   SPI_CONFIG register definition;             */
+#define QCASPI_SLAVE_RESET_BIT (1 << 6)
+
+/*   INTR_CAUSE/ENABLE register definition.      */
+#define SPI_INT_WRBUF_BELOW_WM (1 << 10)
+#define SPI_INT_CPU_ON         (1 << 6)
+#define SPI_INT_ADDR_ERR       (1 << 3)
+#define SPI_INT_WRBUF_ERR      (1 << 2)
+#define SPI_INT_RDBUF_ERR      (1 << 1)
+#define SPI_INT_PKT_AVLBL      (1 << 0)
+
+void qcaspi_spi_error(struct qcaspi *qca);
+int qcaspi_read_register(struct qcaspi *qca, u16 reg, u16 *result);
+int qcaspi_write_register(struct qcaspi *qca, u16 reg, u16 value);
+int qcaspi_tx_cmd(struct qcaspi *qca, u16 cmd);
+
+#endif /* _QCA_7K_H */