ARM: OMAP2+: clock: remove support for legacy mpurate command line param

The legacy support is wrong and dangerous, as it doesn't take any
OPPs into account and does not scale voltages. Switching mpurate should
be handled through cpufreq.

Signed-off-by: Tero Kristo <t-kristo@ti.com>

arch/arm/mach-omap2/Makefile

@@ -181,7 +181,7 @@ obj-$(CONFIG_SOC_DRA7XX)		+= $(clockdomain-common)
 obj-$(CONFIG_SOC_DRA7XX)		+= clockdomains7xx_data.o
 
 # Clock framework
-obj-$(CONFIG_ARCH_OMAP2)		+= $(clock-common) clock2xxx.o
+obj-$(CONFIG_ARCH_OMAP2)		+= $(clock-common)
 obj-$(CONFIG_ARCH_OMAP2)		+= clkt2xxx_dpllcore.o
 obj-$(CONFIG_ARCH_OMAP2)		+= clkt2xxx_virt_prcm_set.o
 obj-$(CONFIG_ARCH_OMAP2)		+= clkt2xxx_dpll.o

arch/arm/mach-omap2/clock.c

@@ -581,47 +581,6 @@ const struct clk_hw_omap_ops clkhwops_wait = {
 	.find_companion	= omap2_clk_dflt_find_companion,
 };
 
-/**
- * omap2_clk_switch_mpurate_at_boot - switch ARM MPU rate by boot-time argument
- * @mpurate_ck_name: clk name of the clock to change rate
- *
- * Change the ARM MPU clock rate to the rate specified on the command
- * line, if one was specified.  @mpurate_ck_name should be
- * "virt_prcm_set" on OMAP2xxx and "dpll1_ck" on OMAP34xx/OMAP36xx.
- * XXX Does not handle voltage scaling - on OMAP2xxx this is currently
- * handled by the virt_prcm_set clock, but this should be handled by
- * the OPP layer.  XXX This is intended to be handled by the OPP layer
- * code in the near future and should be removed from the clock code.
- * Returns -EINVAL if 'mpurate' is zero or if clk_set_rate() rejects
- * the rate, -ENOENT if the struct clk referred to by @mpurate_ck_name
- * cannot be found, or 0 upon success.
- */
-int __init omap2_clk_switch_mpurate_at_boot(const char *mpurate_ck_name)
-{
-	struct clk *mpurate_ck;
-	int r;
-
-	if (!mpurate)
-		return -EINVAL;
-
-	mpurate_ck = clk_get(NULL, mpurate_ck_name);
-	if (WARN(IS_ERR(mpurate_ck), "Failed to get %s.\n", mpurate_ck_name))
-		return -ENOENT;
-
-	r = clk_set_rate(mpurate_ck, mpurate);
-	if (r < 0) {
-		WARN(1, "clock: %s: unable to set MPU rate to %d: %d\n",
-		     mpurate_ck_name, mpurate, r);
-		clk_put(mpurate_ck);
-		return -EINVAL;
-	}
-
-	calibrate_delay();
-	clk_put(mpurate_ck);
-
-	return 0;
-}
-
 /**
  * omap2_clk_print_new_rates - print summary of current clock tree rates
  * @hfclkin_ck_name: clk name for the off-chip HF oscillator

arch/arm/mach-omap2/clock.h

@@ -186,7 +186,6 @@ void omap3_dpll_deny_idle(struct clk_hw_omap *clk);
 
 void __init omap2_clk_disable_clkdm_control(void);
 
-int omap2_clk_switch_mpurate_at_boot(const char *mpurate_ck_name);
 void omap2_clk_print_new_rates(const char *hfclkin_ck_name,
 			       const char *core_ck_name,
 			       const char *mpu_ck_name);

arch/arm/mach-omap2/clock3xxx.c

@@ -108,28 +108,3 @@ void __init omap3_clk_lock_dpll5(void)
 	clk_disable_unprepare(dpll5_clk);
 	return;
 }
-
-/* Common clock code */
-
-/*
- * Switch the MPU rate if specified on cmdline.  We cannot do this
- * early until cmdline is parsed.  XXX This should be removed from the
- * clock code and handled by the OPP layer code in the near future.
- */
-static int __init omap3xxx_clk_arch_init(void)
-{
-	int ret;
-
-	if (!cpu_is_omap34xx())
-		return 0;
-
-	ret = omap2_clk_switch_mpurate_at_boot("dpll1_ck");
-	if (!ret)
-		omap2_clk_print_new_rates("osc_sys_ck", "core_ck", "arm_fck");
-
-	return ret;
-}
-
-omap_arch_initcall(omap3xxx_clk_arch_init);
-
-