Merge branch 'drm-intel-fixes' into drm-intel-next

Documentation/ABI/testing/sysfs-platform-asus-laptop

@@ -47,6 +47,20 @@ Date:		January 2007
 KernelVersion:	2.6.20
 Contact:	"Corentin Chary" <corentincj@iksaif.net>
 Description:
-		Control the bluetooth device. 1 means on, 0 means off.
+		Control the wlan device. 1 means on, 0 means off.
 		This may control the led, the device or both.
 Users:		Lapsus
+
+What:		/sys/devices/platform/asus_laptop/wimax
+Date:		October 2010
+KernelVersion:	2.6.37
+Contact:	"Corentin Chary" <corentincj@iksaif.net>
+Description:
+		Control the wimax device. 1 means on, 0 means off.
+
+What:		/sys/devices/platform/asus_laptop/wwan
+Date:		October 2010
+KernelVersion:	2.6.37
+Contact:	"Corentin Chary" <corentincj@iksaif.net>
+Description:
+		Control the wwan (3G) device. 1 means on, 0 means off.

Documentation/ABI/testing/sysfs-platform-eeepc-wmi

@@ -0,0 +1,10 @@
+What:		/sys/devices/platform/eeepc-wmi/cpufv
+Date:		Oct 2010
+KernelVersion:	2.6.37
+Contact:	"Corentin Chary" <corentincj@iksaif.net>
+Description:
+		Change CPU clock configuration (write-only).
+		There are three available clock configuration:
+		    * 0 -> Super Performance Mode
+		    * 1 -> High Performance Mode
+		    * 2 -> Power Saving Mode

Documentation/filesystems/vfs.txt

@@ -660,11 +660,10 @@ struct address_space_operations {
   releasepage: releasepage is called on PagePrivate pages to indicate
         that the page should be freed if possible.  ->releasepage
         should remove any private data from the page and clear the
-        PagePrivate flag.  It may also remove the page from the
-        address_space.  If this fails for some reason, it may indicate
-        failure with a 0 return value.
-	This is used in two distinct though related cases.  The first
-        is when the VM finds a clean page with no active users and
+        PagePrivate flag. If releasepage() fails for some reason, it must
+	indicate failure with a 0 return value.
+	releasepage() is used in two distinct though related cases.  The
+	first is when the VM finds a clean page with no active users and
         wants to make it a free page.  If ->releasepage succeeds, the
         page will be removed from the address_space and become free.
 

Makefile

@@ -1,7 +1,7 @@
 VERSION = 2
 PATCHLEVEL = 6
 SUBLEVEL = 37
-EXTRAVERSION = -rc4
+EXTRAVERSION = -rc5
 NAME = Flesh-Eating Bats with Fangs
 
 # *DOCUMENTATION*

arch/arm/Kconfig

@@ -9,7 +9,7 @@ config ARM
 	select GENERIC_ATOMIC64 if (!CPU_32v6K || !AEABI)
 	select HAVE_OPROFILE if (HAVE_PERF_EVENTS)
 	select HAVE_ARCH_KGDB
-	select HAVE_KPROBES if (!XIP_KERNEL)
+	select HAVE_KPROBES if (!XIP_KERNEL && !THUMB2_KERNEL)
 	select HAVE_KRETPROBES if (HAVE_KPROBES)
 	select HAVE_FUNCTION_TRACER if (!XIP_KERNEL)
 	select HAVE_FTRACE_MCOUNT_RECORD if (!XIP_KERNEL)

arch/arm/boot/Makefile

@@ -70,12 +70,7 @@ else
 $(obj)/uImage: LOADADDR=$(ZRELADDR)
 endif
 
-ifeq ($(CONFIG_THUMB2_KERNEL),y)
-# Set bit 0 to 1 so that "mov pc, rx" switches to Thumb-2 mode
-$(obj)/uImage: STARTADDR=$(shell echo $(LOADADDR) | sed -e "s/.$$/1/")
-else
 $(obj)/uImage: STARTADDR=$(LOADADDR)
-endif
 
 $(obj)/uImage:	$(obj)/zImage FORCE
 	$(call if_changed,uimage)

arch/arm/boot/bootp/init.S

@@ -73,6 +73,8 @@ move:		ldmia	r4!, {r7 - r10}		@ move 32-bytes at a time
 
 		.size	_start, . - _start
 
+		.align
+
 		.type	data,#object
 data:		.word	initrd_start		@ source initrd address
 		.word	initrd_phys		@ destination initrd address

arch/arm/boot/compressed/head.S

@@ -125,16 +125,21 @@ wait:		mrc	p14, 0, pc, c0, c1, 0
  * sort out different calling conventions
  */
 		.align
+		.arm				@ Always enter in ARM state
 start:
 		.type	start,#function
-		.rept	8
+ THUMB(		adr	r12, BSYM(1f)	)
+ THUMB(		bx	r12		)
+ THUMB(		.rept	6		)
+ ARM(		.rept	8		)
 		mov	r0, r0
 		.endr
 
 		b	1f
 		.word	0x016f2818		@ Magic numbers to help the loader
 		.word	start			@ absolute load/run zImage address
 		.word	_edata			@ zImage end address
+ THUMB(		.thumb			)
 1:		mov	r7, r1			@ save architecture ID
 		mov	r8, r2			@ save atags pointer
 
@@ -174,7 +179,8 @@ not_angel:
 		ldr	sp, [r0, #28]
 #ifdef CONFIG_AUTO_ZRELADDR
 		@ determine final kernel image address
-		and	r4, pc, #0xf8000000
+		mov	r4, pc
+		and	r4, r4, #0xf8000000
 		add	r4, r4, #TEXT_OFFSET
 #else
 		ldr	r4, =zreladdr
@@ -445,7 +451,8 @@ __setup_mmu:	sub	r3, r4, #16384		@ Page directory size
  */
 		mov	r1, #0x1e
 		orr	r1, r1, #3 << 10
-		mov	r2, pc, lsr #20
+		mov	r2, pc
+		mov	r2, r2, lsr #20
 		orr	r1, r1, r2, lsl #20
 		add	r0, r3, r2, lsl #2
 		str	r1, [r0], #4

arch/arm/common/gic.c

@@ -146,9 +146,15 @@ static int gic_set_cpu(unsigned int irq, const struct cpumask *mask_val)
 	unsigned int shift = (irq % 4) * 8;
 	unsigned int cpu = cpumask_first(mask_val);
 	u32 val;
+	struct irq_desc *desc;
 
 	spin_lock(&irq_controller_lock);
-	irq_desc[irq].node = cpu;
+	desc = irq_to_desc(irq);
+	if (desc == NULL) {
+		spin_unlock(&irq_controller_lock);
+		return -EINVAL;
+	}
+	desc->node = cpu;
 	val = readl(reg) & ~(0xff << shift);
 	val |= 1 << (cpu + shift);
 	writel(val, reg);
@@ -210,7 +216,7 @@ void __init gic_cascade_irq(unsigned int gic_nr, unsigned int irq)
 void __init gic_dist_init(unsigned int gic_nr, void __iomem *base,
 			  unsigned int irq_start)
 {
-	unsigned int max_irq, i;
+	unsigned int gic_irqs, irq_limit, i;
 	u32 cpumask = 1 << smp_processor_id();
 
 	if (gic_nr >= MAX_GIC_NR)
@@ -226,47 +232,49 @@ void __init gic_dist_init(unsigned int gic_nr, void __iomem *base,
 
 	/*
 	 * Find out how many interrupts are supported.
-	 */
-	max_irq = readl(base + GIC_DIST_CTR) & 0x1f;
-	max_irq = (max_irq + 1) * 32;
-
-	/*
 	 * The GIC only supports up to 1020 interrupt sources.
-	 * Limit this to either the architected maximum, or the
-	 * platform maximum.
 	 */
-	if (max_irq > max(1020, NR_IRQS))
-		max_irq = max(1020, NR_IRQS);
+	gic_irqs = readl(base + GIC_DIST_CTR) & 0x1f;
+	gic_irqs = (gic_irqs + 1) * 32;
+	if (gic_irqs > 1020)
+		gic_irqs = 1020;
 
 	/*
 	 * Set all global interrupts to be level triggered, active low.
 	 */
-	for (i = 32; i < max_irq; i += 16)
+	for (i = 32; i < gic_irqs; i += 16)
 		writel(0, base + GIC_DIST_CONFIG + i * 4 / 16);
 
 	/*
 	 * Set all global interrupts to this CPU only.
 	 */
-	for (i = 32; i < max_irq; i += 4)
+	for (i = 32; i < gic_irqs; i += 4)
 		writel(cpumask, base + GIC_DIST_TARGET + i * 4 / 4);
 
 	/*
 	 * Set priority on all global interrupts.
 	 */
-	for (i = 32; i < max_irq; i += 4)
+	for (i = 32; i < gic_irqs; i += 4)
 		writel(0xa0a0a0a0, base + GIC_DIST_PRI + i * 4 / 4);
 
 	/*
 	 * Disable all interrupts.  Leave the PPI and SGIs alone
 	 * as these enables are banked registers.
 	 */
-	for (i = 32; i < max_irq; i += 32)
+	for (i = 32; i < gic_irqs; i += 32)
 		writel(0xffffffff, base + GIC_DIST_ENABLE_CLEAR + i * 4 / 32);
 
+	/*
+	 * Limit number of interrupts registered to the platform maximum
+	 */
+	irq_limit = gic_data[gic_nr].irq_offset + gic_irqs;
+	if (WARN_ON(irq_limit > NR_IRQS))
+		irq_limit = NR_IRQS;
+
 	/*
 	 * Setup the Linux IRQ subsystem.
 	 */
-	for (i = irq_start; i < gic_data[gic_nr].irq_offset + max_irq; i++) {
+	for (i = irq_start; i < irq_limit; i++) {
 		set_irq_chip(i, &gic_chip);
 		set_irq_chip_data(i, &gic_data[gic_nr]);
 		set_irq_handler(i, handle_level_irq);

arch/arm/kernel/entry-armv.S

@@ -911,7 +911,7 @@ __kuser_cmpxchg:				@ 0xffff0fc0
 	 * A special ghost syscall is used for that (see traps.c).
 	 */
 	stmfd	sp!, {r7, lr}
-	ldr	r7, =1f			@ it's 20 bits
+	ldr	r7, 1f			@ it's 20 bits
 	swi	__ARM_NR_cmpxchg
 	ldmfd	sp!, {r7, pc}
 1:	.word	__ARM_NR_cmpxchg

arch/arm/kernel/head.S

@@ -85,9 +85,11 @@ ENTRY(stext)
 	mrc	p15, 0, r9, c0, c0		@ get processor id
 	bl	__lookup_processor_type		@ r5=procinfo r9=cpuid
 	movs	r10, r5				@ invalid processor (r5=0)?
+ THUMB( it	eq )		@ force fixup-able long branch encoding
 	beq	__error_p			@ yes, error 'p'
 	bl	__lookup_machine_type		@ r5=machinfo
 	movs	r8, r5				@ invalid machine (r5=0)?
+ THUMB( it	eq )		@ force fixup-able long branch encoding
 	beq	__error_a			@ yes, error 'a'
 	bl	__vet_atags
 #ifdef CONFIG_SMP_ON_UP
@@ -262,6 +264,7 @@ __create_page_tables:
 	mov	pc, lr
 ENDPROC(__create_page_tables)
 	.ltorg
+	.align
 __enable_mmu_loc:
 	.long	.
 	.long	__enable_mmu
@@ -282,6 +285,7 @@ ENTRY(secondary_startup)
 	bl	__lookup_processor_type
 	movs	r10, r5				@ invalid processor?
 	moveq	r0, #'p'			@ yes, error 'p'
+ THUMB( it	eq )		@ force fixup-able long branch encoding
 	beq	__error_p
 
 	/*
@@ -308,6 +312,8 @@ ENTRY(__secondary_switched)
 	b	secondary_start_kernel
 ENDPROC(__secondary_switched)
 
+	.align
+
 	.type	__secondary_data, %object
 __secondary_data:
 	.long	.
@@ -413,6 +419,7 @@ __fixup_smp_on_up:
 	mov	pc, lr
 ENDPROC(__fixup_smp)
 
+	.align
 1:	.word	.
 	.word	__smpalt_begin
 	.word	__smpalt_end

arch/arm/kernel/relocate_kernel.S

@@ -59,6 +59,8 @@ relocate_new_kernel:
 	ldr r2,kexec_boot_atags
 	mov pc,lr
 
+	.align
+
 	.globl kexec_start_address
 kexec_start_address:
 	.long	0x0

arch/arm/mach-cns3xxx/pcie.c

@@ -369,7 +369,7 @@ static int __init cns3xxx_pcie_init(void)
 {
 	int i;
 
-	hook_fault_code(16 + 6, cns3xxx_pcie_abort_handler, SIGBUS,
+	hook_fault_code(16 + 6, cns3xxx_pcie_abort_handler, SIGBUS, 0,
 			"imprecise external abort");
 
 	for (i = 0; i < ARRAY_SIZE(cns3xxx_pcie); i++) {

arch/arm/mach-realview/headsmp.S

@@ -35,5 +35,6 @@ pen:	ldr	r7, [r6]
 	 */
 	b	secondary_startup
 
+	.align
 1:	.long	.
 	.long	pen_release

arch/arm/mach-s3c2412/Kconfig

@@ -16,7 +16,7 @@ config CPU_S3C2412
 config CPU_S3C2412_ONLY
 	bool
 	depends on ARCH_S3C2410 && !CPU_S3C2400 && !CPU_S3C2410 && \
-		   !CPU_2416 && !CPU_S3C2440 && !CPU_S3C2442 && \
+		   !CPU_S3C2416 && !CPU_S3C2440 && !CPU_S3C2442 && \
 		   !CPU_S3C2443 && CPU_S3C2412
 	default y if CPU_S3C2412
 

arch/arm/mach-s3c2416/Kconfig

@@ -35,9 +35,12 @@ menu "S3C2416 Machines"
 config MACH_SMDK2416
 	bool "SMDK2416"
 	select CPU_S3C2416
+	select MACH_SMDK
 	select S3C_DEV_FB
 	select S3C_DEV_HSMMC
 	select S3C_DEV_HSMMC1
+	select S3C_DEV_NAND
+	select S3C_DEV_USB_HOST
 	select S3C2416_PM if PM
 	help
 	  Say Y here if you are using an SMDK2416

arch/arm/mach-s3c2440/Kconfig

@@ -18,6 +18,7 @@ config CPU_S3C2440
 config CPU_S3C2442
 	bool
 	select CPU_ARM920T
+	select S3C_GPIO_PULL_DOWN
 	select S3C2410_CLOCK
 	select S3C2410_GPIO
 	select S3C2410_PM if PM
@@ -178,6 +179,9 @@ config MACH_MINI2440
 	bool "MINI2440 development board"
 	select CPU_S3C2440
 	select EEPROM_AT24
+	select NEW_LEDS
+	select LEDS_CLASS
+	select LEDS_TRIGGER
 	select LEDS_TRIGGER_BACKLIGHT
 	select S3C_DEV_NAND
 	select S3C_DEV_USB_HOST

arch/arm/mach-s3c2440/s3c2440.c

@@ -46,9 +46,6 @@ int __init s3c2440_init(void)
 {
 	printk("S3C2440: Initialising architecture\n");
 
-	s3c24xx_gpiocfg_default.set_pull = s3c_gpio_setpull_1up;
-	s3c24xx_gpiocfg_default.get_pull = s3c_gpio_getpull_1up;
-
 	/* change irq for watchdog */
 
 	s3c_device_wdt.resource[1].start = IRQ_S3C2440_WDT;
@@ -58,3 +55,11 @@ int __init s3c2440_init(void)
 
 	return sysdev_register(&s3c2440_sysdev);
 }
+
+void __init s3c2440_map_io(void)
+{
+	s3c244x_map_io();
+
+	s3c24xx_gpiocfg_default.set_pull = s3c_gpio_setpull_1up;
+	s3c24xx_gpiocfg_default.get_pull = s3c_gpio_getpull_1up;
+}

arch/arm/mach-s3c2440/s3c2442.c

@@ -32,6 +32,7 @@
 #include <linux/interrupt.h>
 #include <linux/ioport.h>
 #include <linux/mutex.h>
+#include <linux/gpio.h>
 #include <linux/clk.h>
 #include <linux/io.h>
 
@@ -43,6 +44,11 @@
 
 #include <plat/clock.h>
 #include <plat/cpu.h>
+#include <plat/s3c244x.h>
+
+#include <plat/gpio-core.h>
+#include <plat/gpio-cfg.h>
+#include <plat/gpio-cfg-helpers.h>
 
 /* S3C2442 extended clock support */
 
@@ -163,3 +169,11 @@ int __init s3c2442_init(void)
 
 	return sysdev_register(&s3c2442_sysdev);
 }
+
+void __init s3c2442_map_io(void)
+{
+	s3c244x_map_io();
+
+	s3c24xx_gpiocfg_default.set_pull = s3c_gpio_setpull_1down;
+	s3c24xx_gpiocfg_default.get_pull = s3c_gpio_getpull_1down;
+}