Ethernet driver for the WIZnet W5300 chip

Based on original driver from chip manufacturer, but nearly full rewite.
Tested and used in production with Blackfin BF531 embedded processor.

Signed-off-by: Mike Sinkovsky <msink@permonline.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/Kconfig

@@ -174,6 +174,7 @@ source "drivers/net/ethernet/tile/Kconfig"
 source "drivers/net/ethernet/toshiba/Kconfig"
 source "drivers/net/ethernet/tundra/Kconfig"
 source "drivers/net/ethernet/via/Kconfig"
+source "drivers/net/ethernet/wiznet/Kconfig"
 source "drivers/net/ethernet/xilinx/Kconfig"
 source "drivers/net/ethernet/xircom/Kconfig"
 

drivers/net/ethernet/Makefile

@@ -73,5 +73,6 @@ obj-$(CONFIG_TILE_NET) += tile/
 obj-$(CONFIG_NET_VENDOR_TOSHIBA) += toshiba/
 obj-$(CONFIG_NET_VENDOR_TUNDRA) += tundra/
 obj-$(CONFIG_NET_VENDOR_VIA) += via/
+obj-$(CONFIG_NET_VENDOR_WIZNET) += wiznet/
 obj-$(CONFIG_NET_VENDOR_XILINX) += xilinx/
 obj-$(CONFIG_NET_VENDOR_XIRCOM) += xircom/

drivers/net/ethernet/wiznet/Kconfig

@@ -0,0 +1,65 @@
+#
+# WIZnet devices configuration
+#
+
+config NET_VENDOR_WIZNET
+	bool "WIZnet devices"
+	default y
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about WIZnet devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_WIZNET
+
+config WIZNET_W5300
+	tristate "WIZnet W5300 Ethernet support"
+	---help---
+	  Support for WIZnet W5300 chips.
+
+	  W5300 is a single chip with integrated 10/100 Ethernet MAC,
+	  PHY and hardware TCP/IP stack, but this driver is limited to
+	  the MAC and PHY functions only, onchip TCP/IP is unused.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called w5300.
+
+choice
+	prompt "WIZnet interface mode"
+	default WIZNET_BUS_ANY
+
+config WIZNET_BUS_DIRECT
+	bool "Direct address bus mode"
+	---help---
+	  In direct address mode host system can directly access all registers
+	  after mapping to Memory-Mapped I/O space.
+
+config WIZNET_BUS_INDIRECT
+	bool "Indirect address bus mode"
+	---help---
+	  In indirect address mode host system indirectly accesses registers
+	  using Indirect Mode Address Register and Indirect Mode Data Register,
+	  which are directly mapped to Memory-Mapped I/O space.
+
+config WIZNET_BUS_ANY
+	bool "Select interface mode in runtime"
+	---help---
+	  If interface mode is unknown in compile time, it can be selected
+	  in runtime from board/platform resources configuration.
+
+	  Performance may decrease compared to explicitly selected bus mode.
+endchoice
+
+config WIZNET_TX_FLOW
+	bool "Use transmit flow control"
+	default y
+	help
+	  This enables transmit flow control for WIZnet chips.
+	  If unsure, say Y.
+
+endif # NET_VENDOR_WIZNET

drivers/net/ethernet/wiznet/Makefile

@@ -0,0 +1 @@
+obj-$(CONFIG_WIZNET_W5300) += w5300.o