Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/…

…davem/net-2.6

Conflicts:
	drivers/ieee802154/fakehard.c
	drivers/net/e1000e/ich8lan.c
	drivers/net/e1000e/phy.c
	drivers/net/netxen/netxen_nic_init.c
	drivers/net/wireless/ath/ath9k/main.c

drivers/ieee802154/fakehard.c

@@ -284,13 +284,13 @@ static netdev_tx_t ieee802154_fake_xmit(struct sk_buff *skb,
 {
 	skb->skb_iif = dev->ifindex;
 	skb->dev = dev;
+
 	dev->stats.tx_packets++;
 	dev->stats.tx_bytes += skb->len;
 
-	dev->trans_start = jiffies;
-
 	/* FIXME: do hardware work here ... */
 
+	dev_kfree_skb(skb);
 	return NETDEV_TX_OK;
 }
 

drivers/net/Kconfig

@@ -975,7 +975,7 @@ config ENC28J60_WRITEVERIFY
 
 config ETHOC
 	tristate "OpenCores 10/100 Mbps Ethernet MAC support"
-	depends on NET_ETHERNET && HAS_IOMEM
+	depends on NET_ETHERNET && HAS_IOMEM && HAS_DMA
 	select MII
 	select PHYLIB
 	select CRC32

drivers/net/au1000_eth.c

@@ -1088,7 +1088,14 @@ static struct net_device * au1000_probe(int port_num)
 		return NULL;
 	}
 
-	if ((err = register_netdev(dev)) != 0) {
+	dev->base_addr = base;
+	dev->irq = irq;
+	dev->netdev_ops = &au1000_netdev_ops;
+	SET_ETHTOOL_OPS(dev, &au1000_ethtool_ops);
+	dev->watchdog_timeo = ETH_TX_TIMEOUT;
+
+	err = register_netdev(dev);
+	if (err != 0) {
 		printk(KERN_ERR "%s: Cannot register net device, error %d\n",
 				DRV_NAME, err);
 		free_netdev(dev);
@@ -1209,12 +1216,6 @@ static struct net_device * au1000_probe(int port_num)
 		aup->tx_db_inuse[i] = pDB;
 	}
 
-	dev->base_addr = base;
-	dev->irq = irq;
-	dev->netdev_ops = &au1000_netdev_ops;
-	SET_ETHTOOL_OPS(dev, &au1000_ethtool_ops);
-	dev->watchdog_timeo = ETH_TX_TIMEOUT;
-
 	/*
 	 * The boot code uses the ethernet controller, so reset it to start
 	 * fresh.  au1000_init() expects that the device is in reset state.

drivers/net/e1000e/e1000.h

@@ -142,6 +142,8 @@ struct e1000_info;
 #define HV_TNCRS_UPPER		PHY_REG(778, 29) /* Transmit with no CRS */
 #define HV_TNCRS_LOWER		PHY_REG(778, 30)
 
+#define E1000_FCRTV_PCH     0x05F40 /* PCH Flow Control Refresh Timer Value */
+
 /* BM PHY Copper Specific Status */
 #define BM_CS_STATUS                      17
 #define BM_CS_STATUS_LINK_UP              0x0400

drivers/net/e1000e/ich8lan.c

@@ -1110,7 +1110,8 @@ static s32 e1000_oem_bits_config_ich8lan(struct e1000_hw *hw, bool d0_state)
 			oem_reg |= HV_OEM_BITS_LPLU;
 	}
 	/* Restart auto-neg to activate the bits */
-	oem_reg |= HV_OEM_BITS_RESTART_AN;
+	if (!e1000_check_reset_block(hw))
+		oem_reg |= HV_OEM_BITS_RESTART_AN;
 	ret_val = hw->phy.ops.write_reg_locked(hw, HV_OEM_BITS, oem_reg);
 
 out:
@@ -3545,6 +3546,7 @@ struct e1000_info e1000_pch_info = {
 				  | FLAG_HAS_AMT
 				  | FLAG_HAS_FLASH
 				  | FLAG_HAS_JUMBO_FRAMES
+				  | FLAG_DISABLE_FC_PAUSE_TIME /* errata */
 				  | FLAG_APME_IN_WUC,
 	.pba			= 26,
 	.max_hw_frame_size	= 4096,

drivers/net/e1000e/netdev.c

@@ -2760,25 +2760,38 @@ void e1000e_reset(struct e1000_adapter *adapter)
 	/*
 	 * flow control settings
 	 *
-	 * The high water mark must be low enough to fit two full frame
+	 * The high water mark must be low enough to fit one full frame
 	 * (or the size used for early receive) above it in the Rx FIFO.
 	 * Set it to the lower of:
 	 * - 90% of the Rx FIFO size, and
 	 * - the full Rx FIFO size minus the early receive size (for parts
 	 *   with ERT support assuming ERT set to E1000_ERT_2048), or
-	 * - the full Rx FIFO size minus two full frames
+	 * - the full Rx FIFO size minus one full frame
 	 */
-	if ((adapter->flags & FLAG_HAS_ERT) &&
-	    (adapter->netdev->mtu > ETH_DATA_LEN))
-		hwm = min(((pba << 10) * 9 / 10),
-			  ((pba << 10) - (E1000_ERT_2048 << 3)));
-	else
-		hwm = min(((pba << 10) * 9 / 10),
-			  ((pba << 10) - (2 * adapter->max_frame_size)));
+	if (hw->mac.type == e1000_pchlan) {
+		/*
+		 * Workaround PCH LOM adapter hangs with certain network
+		 * loads.  If hangs persist, try disabling Tx flow control.
+		 */
+		if (adapter->netdev->mtu > ETH_DATA_LEN) {
+			fc->high_water = 0x3500;
+			fc->low_water  = 0x1500;
+		} else {
+			fc->high_water = 0x5000;
+			fc->low_water  = 0x3000;
+		}
+	} else {
+		if ((adapter->flags & FLAG_HAS_ERT) &&
+		    (adapter->netdev->mtu > ETH_DATA_LEN))
+			hwm = min(((pba << 10) * 9 / 10),
+				  ((pba << 10) - (E1000_ERT_2048 << 3)));
+		else
+			hwm = min(((pba << 10) * 9 / 10),
+				  ((pba << 10) - adapter->max_frame_size));
 
-	fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */
-	fc->low_water = (fc->high_water - (2 * adapter->max_frame_size));
-	fc->low_water &= E1000_FCRTL_RTL; /* 8-byte granularity */
+		fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */
+		fc->low_water = fc->high_water - 8;
+	}
 
 	if (adapter->flags & FLAG_DISABLE_FC_PAUSE_TIME)
 		fc->pause_time = 0xFFFF;
@@ -2804,6 +2817,10 @@ void e1000e_reset(struct e1000_adapter *adapter)
 	if (mac->ops.init_hw(hw))
 		e_err("Hardware Error\n");
 
+	/* additional part of the flow-control workaround above */
+	if (hw->mac.type == e1000_pchlan)
+		ew32(FCRTV_PCH, 0x1000);
+
 	e1000_update_mng_vlan(adapter);
 
 	/* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */
@@ -3612,7 +3629,7 @@ static void e1000_watchdog_task(struct work_struct *work)
 			case SPEED_100:
 				txb2b = 0;
 				netdev->tx_queue_len = 100;
-				/* maybe add some timeout factor ? */
+				adapter->tx_timeout_factor = 10;
 				break;
 			}
 
@@ -4284,8 +4301,10 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
 
 	while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
 		msleep(1);
-	/* e1000e_down has a dependency on max_frame_size */
+	/* e1000e_down -> e1000e_reset dependent on max_frame_size & mtu */
 	adapter->max_frame_size = max_frame;
+	e_info("changing MTU from %d to %d\n", netdev->mtu, new_mtu);
+	netdev->mtu = new_mtu;
 	if (netif_running(netdev))
 		e1000e_down(adapter);
 
@@ -4315,9 +4334,6 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
 		adapter->rx_buffer_len = ETH_FRAME_LEN + VLAN_HLEN
 					 + ETH_FCS_LEN;
 
-	e_info("changing MTU from %d to %d\n", netdev->mtu, new_mtu);
-	netdev->mtu = new_mtu;
-
 	if (netif_running(netdev))
 		e1000e_up(adapter);
 	else

drivers/net/e1000e/phy.c

@@ -71,7 +71,6 @@ static const u16 e1000_igp_2_cable_length_table[] =
 #define I82577_CFG_ASSERT_CRS_ON_TX       (1 << 15)
 #define I82577_CFG_ENABLE_DOWNSHIFT       (3 << 10) /* auto downshift 100/10 */
 #define I82577_CTRL_REG                   23
-#define I82577_CTRL_DOWNSHIFT_MASK        (7 << 10)
 
 /* 82577 specific PHY registers */
 #define I82577_PHY_CTRL_2            18
@@ -660,15 +659,6 @@ s32 e1000_copper_link_setup_82577(struct e1000_hw *hw)
 	phy_data |= I82577_CFG_ENABLE_DOWNSHIFT;
 
 	ret_val = phy->ops.write_reg(hw, I82577_CFG_REG, phy_data);
-	if (ret_val)
-		goto out;
-
-	/* Set number of link attempts before downshift */
-	ret_val = phy->ops.read_reg(hw, I82577_CTRL_REG, &phy_data);
-	if (ret_val)
-		goto out;
-	phy_data &= ~I82577_CTRL_DOWNSHIFT_MASK;
-	ret_val = phy->ops.write_reg(hw, I82577_CTRL_REG, phy_data);
 
 out:
 	return ret_val;
@@ -2658,27 +2648,26 @@ static s32 __e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data,
 		page = 0;
 
 	if (reg > MAX_PHY_MULTI_PAGE_REG) {
-		if ((hw->phy.type != e1000_phy_82578) ||
-		    ((reg != I82578_ADDR_REG) &&
-		     (reg != I82578_ADDR_REG + 1))) {
-			u32 phy_addr = hw->phy.addr;
+		u32 phy_addr = hw->phy.addr;
 
-			hw->phy.addr = 1;
+		hw->phy.addr = 1;
 
-			/* Page is shifted left, PHY expects (page x 32) */
-			ret_val = e1000e_write_phy_reg_mdic(hw,
-			                             IGP01E1000_PHY_PAGE_SELECT,
-			                             (page << IGP_PAGE_SHIFT));
-			hw->phy.addr = phy_addr;
-		}
+		/* Page is shifted left, PHY expects (page x 32) */
+		ret_val = e1000e_write_phy_reg_mdic(hw,
+					     IGP01E1000_PHY_PAGE_SELECT,
+					     (page << IGP_PAGE_SHIFT));
+		hw->phy.addr = phy_addr;
+
+		if (ret_val)
+			goto out;
 	}
 
 	ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & reg,
 	                                  data);
 out:
 	/* Revert to MDIO fast mode, if applicable */
 	if ((hw->phy.type == e1000_phy_82577) && in_slow_mode)
-		ret_val = e1000_set_mdio_slow_mode_hv(hw, false);
+		ret_val |= e1000_set_mdio_slow_mode_hv(hw, false);
 
 	if (!locked)
 		hw->phy.ops.release(hw);
@@ -2784,19 +2773,18 @@ static s32 __e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data,
 	}
 
 	if (reg > MAX_PHY_MULTI_PAGE_REG) {
-		if ((hw->phy.type != e1000_phy_82578) ||
-		    ((reg != I82578_ADDR_REG) &&
-		     (reg != I82578_ADDR_REG + 1))) {
-			u32 phy_addr = hw->phy.addr;
+		u32 phy_addr = hw->phy.addr;
 
-			hw->phy.addr = 1;
+		hw->phy.addr = 1;
 
-			/* Page is shifted left, PHY expects (page x 32) */
-			ret_val = e1000e_write_phy_reg_mdic(hw,
-			                             IGP01E1000_PHY_PAGE_SELECT,
-			                             (page << IGP_PAGE_SHIFT));
-			hw->phy.addr = phy_addr;
-		}
+		/* Page is shifted left, PHY expects (page x 32) */
+		ret_val = e1000e_write_phy_reg_mdic(hw,
+					     IGP01E1000_PHY_PAGE_SELECT,
+					     (page << IGP_PAGE_SHIFT));
+		hw->phy.addr = phy_addr;
+
+		if (ret_val)
+			goto out;
 	}
 
 	ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & reg,
@@ -2805,7 +2793,7 @@ static s32 __e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data,
 out:
 	/* Revert to MDIO fast mode, if applicable */
 	if ((hw->phy.type == e1000_phy_82577) && in_slow_mode)
-		ret_val = e1000_set_mdio_slow_mode_hv(hw, false);
+		ret_val |= e1000_set_mdio_slow_mode_hv(hw, false);
 
 	if (!locked)
 		hw->phy.ops.release(hw);

drivers/net/ixgbe/ixgbe_main.c

@@ -242,11 +242,11 @@ static void ixgbe_unmap_and_free_tx_resource(struct ixgbe_adapter *adapter,
 static inline bool ixgbe_tx_is_paused(struct ixgbe_adapter *adapter,
                                       struct ixgbe_ring *tx_ring)
 {
-	int tc;
 	u32 txoff = IXGBE_TFCS_TXOFF;
 
 #ifdef CONFIG_IXGBE_DCB
 	if (adapter->flags & IXGBE_FLAG_DCB_ENABLED) {
+		int tc;
 		int reg_idx = tx_ring->reg_idx;
 		int dcb_i = adapter->ring_feature[RING_F_DCB].indices;