Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/ker…

…nel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
 "Nothing very controversial in here.  Most of the fixes are for OMAP
  this time around, with some orion/kirkwood and a tegra patch mixed in."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: Orion: Fix Virtual/Physical mixup with watchdog
  ARM: Kirkwood: clk_register_gate_fn: add fn assignment
  ARM: Orion5x - Restore parts of io.h, with rework
  ARM: OMAP4: hwmod data: Force HDMI in no-idle while enabled
  ARM: OMAP2+: mux: fix sparse warning
  ARM: OMAP2+: CM: increase the module disable timeout
  ARM: OMAP4: clock data: add clockdomains for clocks used as main clocks
  ARM: OMAP4: hwmod data: fix 32k sync timer idle modes
  ARM: OMAP4+: hwmod: fix issue causing IPs not going back to Smart-Standby
  ARM: OMAP: Fix Beagleboard DVI reset gpio
  arm/dts: OMAP2: Fix interrupt controller binding
  ARM: OMAP2: Fix tusb6010 GPIO interrupt for n8x0
  ARM: OMAP2+: Fix MUSB ifdefs for platform init code
  ARM: tegra: make tegra_cpu_reset_handler_enable() __init
  ARM: OMAP: PM: Lock clocks list while generating summary
  ARM: iconnect: Remove include of removed linux/spi/orion_spi.h

arch/arm/Kconfig

@@ -589,6 +589,7 @@ config ARCH_ORION5X
 	select PCI
 	select ARCH_REQUIRE_GPIOLIB
 	select GENERIC_CLOCKEVENTS
+	select NEED_MACH_IO_H
 	select PLAT_ORION
 	help
 	  Support for the following Marvell Orion 5x series SoCs:

arch/arm/boot/dts/omap2.dtsi

@@ -44,6 +44,8 @@
 			compatible = "ti,omap2-intc";
 			interrupt-controller;
 			#interrupt-cells = <1>;
+			ti,intc-size = <96>;
+			reg = <0x480FE000 0x1000>;
 		};
 
 		uart1: serial@4806a000 {

arch/arm/mach-kirkwood/board-iconnect.c

@@ -20,9 +20,6 @@
 #include <linux/mv643xx_eth.h>
 #include <linux/gpio.h>
 #include <linux/leds.h>
-#include <linux/spi/flash.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/orion_spi.h>
 #include <linux/i2c.h>
 #include <linux/input.h>
 #include <linux/gpio_keys.h>

arch/arm/mach-kirkwood/common.c

@@ -159,6 +159,7 @@ static struct clk __init *clk_register_gate_fn(struct device *dev,
 	gate_fn->gate.flags = clk_gate_flags;
 	gate_fn->gate.lock = lock;
 	gate_fn->gate.hw.init = &init;
+	gate_fn->fn = fn;
 
 	/* ops is the gate ops, but with our disable function */
 	if (clk_gate_fn_ops.disable != clk_gate_fn_disable) {

arch/arm/mach-kirkwood/include/mach/bridge-regs.h

@@ -38,6 +38,7 @@
 #define IRQ_MASK_HIGH_OFF	0x0014
 
 #define TIMER_VIRT_BASE		(BRIDGE_VIRT_BASE | 0x0300)
+#define TIMER_PHYS_BASE		(BRIDGE_PHYS_BASE | 0x0300)
 
 #define L2_CONFIG_REG		(BRIDGE_VIRT_BASE | 0x0128)
 #define L2_WRITETHROUGH		0x00000010

arch/arm/mach-kirkwood/include/mach/kirkwood.h

@@ -80,6 +80,7 @@
 #define  UART1_VIRT_BASE	(DEV_BUS_VIRT_BASE | 0x2100)
 
 #define BRIDGE_VIRT_BASE	(KIRKWOOD_REGS_VIRT_BASE | 0x20000)
+#define BRIDGE_PHYS_BASE	(KIRKWOOD_REGS_PHYS_BASE | 0x20000)
 
 #define CRYPTO_PHYS_BASE	(KIRKWOOD_REGS_PHYS_BASE | 0x30000)
 

arch/arm/mach-omap2/board-n8x0.c

@@ -83,11 +83,9 @@ static struct musb_hdrc_config musb_config = {
 };
 
 static struct musb_hdrc_platform_data tusb_data = {
-#if defined(CONFIG_USB_MUSB_OTG)
+#ifdef CONFIG_USB_GADGET_MUSB_HDRC
 	.mode		= MUSB_OTG,
-#elif defined(CONFIG_USB_MUSB_PERIPHERAL)
-	.mode		= MUSB_PERIPHERAL,
-#else /* defined(CONFIG_USB_MUSB_HOST) */
+#else
 	.mode		= MUSB_HOST,
 #endif
 	.set_power	= tusb_set_power,

arch/arm/mach-omap2/board-omap3beagle.c

@@ -81,13 +81,13 @@ static u8 omap3_beagle_version;
 static struct {
 	int mmc1_gpio_wp;
 	int usb_pwr_level;
-	int reset_gpio;
+	int dvi_pd_gpio;
 	int usr_button_gpio;
 	int mmc_caps;
 } beagle_config = {
 	.mmc1_gpio_wp = -EINVAL,
 	.usb_pwr_level = GPIOF_OUT_INIT_LOW,
-	.reset_gpio = 129,
+	.dvi_pd_gpio = -EINVAL,
 	.usr_button_gpio = 4,
 	.mmc_caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 };
@@ -126,21 +126,21 @@ static void __init omap3_beagle_init_rev(void)
 		printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
 		omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX;
 		beagle_config.mmc1_gpio_wp = 29;
-		beagle_config.reset_gpio = 170;
+		beagle_config.dvi_pd_gpio = 170;
 		beagle_config.usr_button_gpio = 7;
 		break;
 	case 6:
 		printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
 		omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3;
 		beagle_config.mmc1_gpio_wp = 23;
-		beagle_config.reset_gpio = 170;
+		beagle_config.dvi_pd_gpio = 170;
 		beagle_config.usr_button_gpio = 7;
 		break;
 	case 5:
 		printk(KERN_INFO "OMAP3 Beagle Rev: C4\n");
 		omap3_beagle_version = OMAP3BEAGLE_BOARD_C4;
 		beagle_config.mmc1_gpio_wp = 23;
-		beagle_config.reset_gpio = 170;
+		beagle_config.dvi_pd_gpio = 170;
 		beagle_config.usr_button_gpio = 7;
 		break;
 	case 0:
@@ -274,11 +274,9 @@ static int beagle_twl_gpio_setup(struct device *dev,
 		if (r)
 			pr_err("%s: unable to configure nDVI_PWR_EN\n",
 				__func__);
-		r = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH,
-				     "DVI_LDO_EN");
-		if (r)
-			pr_err("%s: unable to configure DVI_LDO_EN\n",
-				__func__);
+
+		beagle_config.dvi_pd_gpio = gpio + 2;
+
 	} else {
 		/*
 		 * REVISIT: need ehci-omap hooks for external VBUS
@@ -287,7 +285,7 @@ static int beagle_twl_gpio_setup(struct device *dev,
 		if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
 			pr_err("%s: unable to configure EHCI_nOC\n", __func__);
 	}
-	dvi_panel.power_down_gpio = beagle_config.reset_gpio;
+	dvi_panel.power_down_gpio = beagle_config.dvi_pd_gpio;
 
 	gpio_request_one(gpio + TWL4030_GPIO_MAX, beagle_config.usb_pwr_level,
 			"nEN_USB_PWR");
@@ -499,7 +497,7 @@ static void __init omap3_beagle_init(void)
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
 	omap3_beagle_init_rev();
 
-	if (beagle_config.mmc1_gpio_wp != -EINVAL)
+	if (gpio_is_valid(beagle_config.mmc1_gpio_wp))
 		omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
 	mmc[0].caps = beagle_config.mmc_caps;
 	omap_hsmmc_init(mmc);
@@ -510,15 +508,13 @@ static void __init omap3_beagle_init(void)
 
 	platform_add_devices(omap3_beagle_devices,
 			ARRAY_SIZE(omap3_beagle_devices));
+	if (gpio_is_valid(beagle_config.dvi_pd_gpio))
+		omap_mux_init_gpio(beagle_config.dvi_pd_gpio, OMAP_PIN_OUTPUT);
 	omap_display_init(&beagle_dss_data);
 	omap_serial_init();
 	omap_sdrc_init(mt46h32m32lf6_sdrc_params,
 				  mt46h32m32lf6_sdrc_params);
 
-	omap_mux_init_gpio(170, OMAP_PIN_INPUT);
-	/* REVISIT leave DVI powered down until it's needed ... */
-	gpio_request_one(170, GPIOF_OUT_INIT_HIGH, "DVI_nPD");
-
 	usb_musb_init(NULL);
 	usbhs_init(&usbhs_bdata);
 	omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions,

arch/arm/mach-omap2/clock44xx_data.c

@@ -84,6 +84,7 @@ static struct clk slimbus_clk = {
 
 static struct clk sys_32k_ck = {
 	.name		= "sys_32k_ck",
+	.clkdm_name	= "prm_clkdm",
 	.rate		= 32768,
 	.ops		= &clkops_null,
 };
@@ -512,6 +513,7 @@ static struct clk ddrphy_ck = {
 	.name		= "ddrphy_ck",
 	.parent		= &dpll_core_m2_ck,
 	.ops		= &clkops_null,
+	.clkdm_name	= "l3_emif_clkdm",
 	.fixed_div	= 2,
 	.recalc		= &omap_fixed_divisor_recalc,
 };
@@ -769,6 +771,7 @@ static const struct clksel dpll_mpu_m2_div[] = {
 static struct clk dpll_mpu_m2_ck = {
 	.name		= "dpll_mpu_m2_ck",
 	.parent		= &dpll_mpu_ck,
+	.clkdm_name	= "cm_clkdm",
 	.clksel		= dpll_mpu_m2_div,
 	.clksel_reg	= OMAP4430_CM_DIV_M2_DPLL_MPU,
 	.clksel_mask	= OMAP4430_DPLL_CLKOUT_DIV_MASK,
@@ -1149,6 +1152,7 @@ static const struct clksel l3_div_div[] = {
 static struct clk l3_div_ck = {
 	.name		= "l3_div_ck",
 	.parent		= &div_core_ck,
+	.clkdm_name	= "cm_clkdm",
 	.clksel		= l3_div_div,
 	.clksel_reg	= OMAP4430_CM_CLKSEL_CORE,
 	.clksel_mask	= OMAP4430_CLKSEL_L3_MASK,
@@ -2824,6 +2828,7 @@ static const struct clksel trace_clk_div_div[] = {
 static struct clk trace_clk_div_ck = {
 	.name		= "trace_clk_div_ck",
 	.parent		= &pmd_trace_clk_mux_ck,
+	.clkdm_name	= "emu_sys_clkdm",
 	.clksel		= trace_clk_div_div,
 	.clksel_reg	= OMAP4430_CM_EMU_DEBUGSS_CLKCTRL,
 	.clksel_mask	= OMAP4430_CLKSEL_PMD_TRACE_CLK_MASK,

arch/arm/mach-omap2/cm.h

@@ -22,4 +22,15 @@
  */
 #define MAX_MODULE_READY_TIME		2000
 
+/*
+ * MAX_MODULE_DISABLE_TIME: max duration in microseconds to wait for
+ * the PRCM to request that a module enter the inactive state in the
+ * case of OMAP2 & 3.  In the case of OMAP4 this is the max duration
+ * in microseconds for the module to reach the inactive state from
+ * a functional state.
+ * XXX FSUSB on OMAP4430 takes ~4ms to idle after reset during
+ * kernel init.
+ */
+#define MAX_MODULE_DISABLE_TIME		5000
+
 #endif

arch/arm/mach-omap2/cminst44xx.c

@@ -313,9 +313,9 @@ int omap4_cminst_wait_module_idle(u8 part, u16 inst, s16 cdoffs, u16 clkctrl_off
 
 	omap_test_timeout((_clkctrl_idlest(part, inst, cdoffs, clkctrl_offs) ==
 			   CLKCTRL_IDLEST_DISABLED),
-			  MAX_MODULE_READY_TIME, i);
+			  MAX_MODULE_DISABLE_TIME, i);
 
-	return (i < MAX_MODULE_READY_TIME) ? 0 : -EBUSY;
+	return (i < MAX_MODULE_DISABLE_TIME) ? 0 : -EBUSY;
 }
 
 /**

arch/arm/mach-omap2/mux.c

@@ -41,6 +41,7 @@
 #include "control.h"
 #include "mux.h"
 #include "prm.h"
+#include "common.h"
 
 #define OMAP_MUX_BASE_OFFSET		0x30	/* Offset from CTRL_BASE */
 #define OMAP_MUX_BASE_SZ		0x5ca

arch/arm/mach-omap2/omap_hwmod.c

@@ -530,7 +530,7 @@ static int _disable_wakeup(struct omap_hwmod *oh, u32 *v)
 	if (oh->class->sysc->idlemodes & SIDLE_SMART_WKUP)
 		_set_slave_idlemode(oh, HWMOD_IDLEMODE_SMART, v);
 	if (oh->class->sysc->idlemodes & MSTANDBY_SMART_WKUP)
-		_set_master_standbymode(oh, HWMOD_IDLEMODE_SMART_WKUP, v);
+		_set_master_standbymode(oh, HWMOD_IDLEMODE_SMART, v);
 
 	/* XXX test pwrdm_get_wken for this hwmod's subsystem */
 

arch/arm/mach-omap2/omap_hwmod_44xx_data.c

@@ -393,8 +393,7 @@ static struct omap_hwmod_class_sysconfig omap44xx_counter_sysc = {
 	.rev_offs	= 0x0000,
 	.sysc_offs	= 0x0004,
 	.sysc_flags	= SYSC_HAS_SIDLEMODE,
-	.idlemodes	= (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART |
-			   SIDLE_SMART_WKUP),
+	.idlemodes	= (SIDLE_FORCE | SIDLE_NO),
 	.sysc_fields	= &omap_hwmod_sysc_type1,
 };
 
@@ -854,6 +853,11 @@ static struct omap_hwmod omap44xx_dss_hdmi_hwmod = {
 	.name		= "dss_hdmi",
 	.class		= &omap44xx_hdmi_hwmod_class,
 	.clkdm_name	= "l3_dss_clkdm",
+	/*
+	 * HDMI audio requires to use no-idle mode. Hence,
+	 * set idle mode by software.
+	 */
+	.flags		= HWMOD_SWSUP_SIDLE,
 	.mpu_irqs	= omap44xx_dss_hdmi_irqs,
 	.sdma_reqs	= omap44xx_dss_hdmi_sdma_reqs,
 	.main_clk	= "dss_48mhz_clk",

arch/arm/mach-omap2/omap_phy_internal.c

@@ -239,21 +239,15 @@ void am35x_set_mode(u8 musb_mode)
 
 	devconf2 &= ~CONF2_OTGMODE;
 	switch (musb_mode) {
-#ifdef	CONFIG_USB_MUSB_HDRC_HCD
 	case MUSB_HOST:		/* Force VBUS valid, ID = 0 */
 		devconf2 |= CONF2_FORCE_HOST;
 		break;
-#endif
-#ifdef	CONFIG_USB_GADGET_MUSB_HDRC
 	case MUSB_PERIPHERAL:	/* Force VBUS valid, ID = 1 */
 		devconf2 |= CONF2_FORCE_DEVICE;
 		break;
-#endif
-#ifdef	CONFIG_USB_MUSB_OTG
 	case MUSB_OTG:		/* Don't override the VBUS/ID comparators */
 		devconf2 |= CONF2_NO_OVERRIDE;
 		break;
-#endif
 	default:
 		pr_info(KERN_INFO "Unsupported mode %u\n", musb_mode);
 	}

arch/arm/mach-omap2/usb-musb.c

@@ -41,12 +41,10 @@ static struct musb_hdrc_config musb_config = {
 };
 
 static struct musb_hdrc_platform_data musb_plat = {
-#ifdef CONFIG_USB_MUSB_OTG
+#ifdef CONFIG_USB_GADGET_MUSB_HDRC
 	.mode		= MUSB_OTG,
-#elif defined(CONFIG_USB_MUSB_HDRC_HCD)
+#else
 	.mode		= MUSB_HOST,
-#elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
-	.mode		= MUSB_PERIPHERAL,
 #endif
 	/* .clock is set dynamically */
 	.config		= &musb_config,

arch/arm/mach-omap2/usb-tusb6010.c

@@ -300,7 +300,7 @@ tusb6010_setup_interface(struct musb_hdrc_platform_data *data,
 		printk(error, 3, status);
 		return status;
 	}
-	tusb_resources[2].start = irq + IH_GPIO_BASE;
+	tusb_resources[2].start = gpio_to_irq(irq);
 
 	/* set up memory timings ... can speed them up later */
 	if (!ps_refclk) {

arch/arm/mach-orion5x/include/mach/bridge-regs.h

@@ -35,5 +35,5 @@
 #define MAIN_IRQ_MASK		(ORION5X_BRIDGE_VIRT_BASE | 0x204)
 
 #define TIMER_VIRT_BASE		(ORION5X_BRIDGE_VIRT_BASE | 0x300)
-
+#define TIMER_PHYS_BASE		(ORION5X_BRIDGE_PHYS_BASE | 0x300)
 #endif

arch/arm/mach-orion5x/include/mach/io.h

@@ -0,0 +1,22 @@
+/*
+ * arch/arm/mach-orion5x/include/mach/io.h
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __ASM_ARCH_IO_H
+#define __ASM_ARCH_IO_H
+
+#include <mach/orion5x.h>
+#include <asm/sizes.h>
+
+#define IO_SPACE_LIMIT		SZ_2M
+static inline void __iomem *__io(unsigned long addr)
+{
+	return (void __iomem *)(addr + ORION5X_PCIE_IO_VIRT_BASE);
+}
+
+#define __io(a)			 __io(a)
+#endif

arch/arm/mach-orion5x/include/mach/orion5x.h

@@ -82,6 +82,7 @@
 #define  UART1_VIRT_BASE		(ORION5X_DEV_BUS_VIRT_BASE | 0x2100)
 
 #define ORION5X_BRIDGE_VIRT_BASE	(ORION5X_REGS_VIRT_BASE | 0x20000)
+#define ORION5X_BRIDGE_PHYS_BASE	(ORION5X_REGS_PHYS_BASE | 0x20000)
 
 #define ORION5X_PCI_VIRT_BASE		(ORION5X_REGS_VIRT_BASE | 0x30000)
 

arch/arm/mach-tegra/reset.c

@@ -33,7 +33,7 @@
 
 static bool is_enabled;
 
-static void tegra_cpu_reset_handler_enable(void)
+static void __init tegra_cpu_reset_handler_enable(void)
 {
 	void __iomem *iram_base = IO_ADDRESS(TEGRA_IRAM_RESET_BASE);
 	void __iomem *evp_cpu_reset =

arch/arm/plat-omap/clock.c

@@ -461,6 +461,7 @@ static int clk_dbg_show_summary(struct seq_file *s, void *unused)
 	struct clk *c;
 	struct clk *pa;
 
+	mutex_lock(&clocks_mutex);
 	seq_printf(s, "%-30s %-30s %-10s %s\n",
 		"clock-name", "parent-name", "rate", "use-count");
 
@@ -469,6 +470,7 @@ static int clk_dbg_show_summary(struct seq_file *s, void *unused)
 		seq_printf(s, "%-30s %-30s %-10lu %d\n",
 			c->name, pa ? pa->name : "none", c->rate, c->usecount);
 	}
+	mutex_unlock(&clocks_mutex);
 
 	return 0;
 }

arch/arm/plat-orion/common.c

@@ -582,7 +582,7 @@ void __init orion_spi_1_init(unsigned long mapbase)
  * Watchdog
  ****************************************************************************/
 static struct resource orion_wdt_resource =
-		DEFINE_RES_MEM(TIMER_VIRT_BASE, 0x28);
+		DEFINE_RES_MEM(TIMER_PHYS_BASE, 0x28);
 
 static struct platform_device orion_wdt_device = {
 	.name		= "orion_wdt",