Merge tag 'wireless-drivers-next-for-davem-2018-05-17' of git://git.k…

…ernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.18

The first pull request for 4.18. As usual new features and bug fixes
but nothing really special.

I also merged wireless-drivers due to an iwlwifi patch dependency.

Major changes:

iwlwifi

* implement Traffic Condition Monitor and use it for scan, BT coex and
  to detect when the AP doesn't support UAPSD properly

* some more work for the 22000 family of devices;

* introduce AMSDU rate control offload

qtnfmac

* DFS offload support

rsi

* roaming enhancements

* increase max supported aggregation subframes

* don't advertise 5 GHz support if the device doesn't support it

brcmfmac

* add support for BCM4366E chipset

* add support for bcm43364 wireless chipset

ath10k

* enable temperature reads for QCA6174 and QCA9377

* add firmware memory dump support for QCA9984

* continue adding WCN3990 support via SNOC bus
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt

@@ -4,6 +4,7 @@ Required properties:
 - compatible: Should be one of the following:
 	* "qcom,ath10k"
 	* "qcom,ipq4019-wifi"
+	* "qcom,wcn3990-wifi"
 
 PCI based devices uses compatible string "qcom,ath10k" and takes calibration
 data along with board specific data via "qcom,ath10k-calibration-data".
@@ -18,8 +19,12 @@ In general, entry "qcom,ath10k-pre-calibration-data" and
 "qcom,ath10k-calibration-data" conflict with each other and only one
 can be provided per device.
 
+SNOC based devices (i.e. wcn3990) uses compatible string "qcom,wcn3990-wifi".
+
 Optional properties:
 - reg: Address and length of the register set for the device.
+- reg-names: Must include the list of following reg names,
+	     "membase"
 - resets: Must contain an entry for each entry in reset-names.
           See ../reset/reseti.txt for details.
 - reset-names: Must include the list of following reset names,
@@ -49,6 +54,8 @@ Optional properties:
 				 hw versions.
 - qcom,ath10k-pre-calibration-data : pre calibration data as an array,
 				     the length can vary between hw versions.
+- <supply-name>-supply: handle to the regulator device tree node
+			   optional "supply-name" is "vdd-0.8-cx-mx".
 
 Example (to supply the calibration data alone):
 
@@ -119,3 +126,27 @@ wifi0: wifi@a000000 {
 	qcom,msi_base = <0x40>;
 	qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ];
 };
+
+Example (to supply wcn3990 SoC wifi block details):
+
+wifi@18000000 {
+		compatible = "qcom,wcn3990-wifi";
+		reg = <0x18800000 0x800000>;
+		reg-names = "membase";
+		clocks = <&clock_gcc clk_aggre2_noc_clk>;
+		clock-names = "smmu_aggre2_noc_clk"
+		interrupts =
+			   <0 130 0 /* CE0 */ >,
+			   <0 131 0 /* CE1 */ >,
+			   <0 132 0 /* CE2 */ >,
+			   <0 133 0 /* CE3 */ >,
+			   <0 134 0 /* CE4 */ >,
+			   <0 135 0 /* CE5 */ >,
+			   <0 136 0 /* CE6 */ >,
+			   <0 137 0 /* CE7 */ >,
+			   <0 138 0 /* CE8 */ >,
+			   <0 139 0 /* CE9 */ >,
+			   <0 140 0 /* CE10 */ >,
+			   <0 141 0 /* CE11 */ >;
+		vdd-0.8-cx-mx-supply = <&pm8998_l5>;
+};

drivers/net/wireless/ath/ath10k/Kconfig

@@ -4,12 +4,16 @@ config ATH10K
 	select ATH_COMMON
 	select CRC32
 	select WANT_DEV_COREDUMP
+	select ATH10K_CE
         ---help---
           This module adds support for wireless adapters based on
           Atheros IEEE 802.11ac family of chipsets.
 
           If you choose to build a module, it'll be called ath10k.
 
+config ATH10K_CE
+	bool
+
 config ATH10K_PCI
 	tristate "Atheros ath10k PCI support"
 	depends on ATH10K && PCI
@@ -36,6 +40,14 @@ config ATH10K_USB
 	  This module adds experimental support for USB bus. Currently
 	  work in progress and will not fully work.
 
+config ATH10K_SNOC
+        tristate "Qualcomm ath10k SNOC support (EXPERIMENTAL)"
+        depends on ATH10K && ARCH_QCOM
+        ---help---
+          This module adds support for integrated WCN3990 chip connected
+          to system NOC(SNOC). Currently work in progress and will not
+          fully work.
+
 config ATH10K_DEBUG
 	bool "Atheros ath10k debugging"
 	depends on ATH10K

drivers/net/wireless/ath/ath10k/Makefile

@@ -22,10 +22,10 @@ ath10k_core-$(CONFIG_THERMAL) += thermal.o
 ath10k_core-$(CONFIG_MAC80211_DEBUGFS) += debugfs_sta.o
 ath10k_core-$(CONFIG_PM) += wow.o
 ath10k_core-$(CONFIG_DEV_COREDUMP) += coredump.o
+ath10k_core-$(CONFIG_ATH10K_CE) += ce.o
 
 obj-$(CONFIG_ATH10K_PCI) += ath10k_pci.o
-ath10k_pci-y += pci.o \
-		ce.o
+ath10k_pci-y += pci.o
 
 ath10k_pci-$(CONFIG_ATH10K_AHB) += ahb.o
 
@@ -35,5 +35,8 @@ ath10k_sdio-y += sdio.o
 obj-$(CONFIG_ATH10K_USB) += ath10k_usb.o
 ath10k_usb-y += usb.o
 
+obj-$(CONFIG_ATH10K_SNOC) += ath10k_snoc.o
+ath10k_snoc-y += snoc.o
+
 # for tracing framework to find trace.h
 CFLAGS_trace.o := -I$(src)