Merge tag 'fixes-for-v4.4-rc2' of git://git.kernel.org/pub/scm/linux/…

…kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v4.4-rc2

First round of fixes for this -rc cycle. We have the
usual set of miscellaneous fixes. The important
thing here is support for Intel Broxton SoC on dwc3,
some fixes for Rockchip SoCs on dwc2 and a fix on
dwc3 to let it report lower speeds than
USB_SPEED_SUPER.

drivers/usb/dwc2/hcd.c

@@ -324,12 +324,13 @@ void dwc2_hcd_disconnect(struct dwc2_hsotg *hsotg)
  */
 static void dwc2_hcd_rem_wakeup(struct dwc2_hsotg *hsotg)
 {
-	if (hsotg->lx_state == DWC2_L2) {
+	if (hsotg->bus_suspended) {
 		hsotg->flags.b.port_suspend_change = 1;
 		usb_hcd_resume_root_hub(hsotg->priv);
-	} else {
-		hsotg->flags.b.port_l1_change = 1;
 	}
+
+	if (hsotg->lx_state == DWC2_L1)
+		hsotg->flags.b.port_l1_change = 1;
 }
 
 /**
@@ -1428,8 +1429,8 @@ static void dwc2_wakeup_detected(unsigned long data)
 	dev_dbg(hsotg->dev, "Clear Resume: HPRT0=%0x\n",
 		dwc2_readl(hsotg->regs + HPRT0));
 
-	hsotg->bus_suspended = 0;
 	dwc2_hcd_rem_wakeup(hsotg);
+	hsotg->bus_suspended = 0;
 
 	/* Change to L0 state */
 	hsotg->lx_state = DWC2_L0;

drivers/usb/dwc2/platform.c

@@ -108,7 +108,8 @@ static const struct dwc2_core_params params_rk3066 = {
 	.host_ls_low_power_phy_clk	= -1,
 	.ts_dline			= -1,
 	.reload_ctl			= -1,
-	.ahbcfg				= 0x7, /* INCR16 */
+	.ahbcfg				= GAHBCFG_HBSTLEN_INCR16 <<
+					  GAHBCFG_HBSTLEN_SHIFT,
 	.uframe_sched			= -1,
 	.external_id_pin_ctl		= -1,
 	.hibernation			= -1,

drivers/usb/dwc3/dwc3-pci.c

@@ -34,6 +34,8 @@
 #define PCI_DEVICE_ID_INTEL_BSW			0x22b7
 #define PCI_DEVICE_ID_INTEL_SPTLP		0x9d30
 #define PCI_DEVICE_ID_INTEL_SPTH		0xa130
+#define PCI_DEVICE_ID_INTEL_BXT			0x0aaa
+#define PCI_DEVICE_ID_INTEL_APL			0x5aaa
 
 static const struct acpi_gpio_params reset_gpios = { 0, 0, false };
 static const struct acpi_gpio_params cs_gpios = { 1, 0, false };
@@ -210,6 +212,8 @@ static const struct pci_device_id dwc3_pci_id_table[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MRFLD), },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_SPTLP), },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_SPTH), },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_BXT), },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_APL), },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_NL_USB), },
 	{  }	/* Terminating Entry */
 };

drivers/usb/dwc3/gadget.c

@@ -2744,11 +2744,33 @@ int dwc3_gadget_init(struct dwc3 *dwc)
 	}
 
 	dwc->gadget.ops			= &dwc3_gadget_ops;
-	dwc->gadget.max_speed		= USB_SPEED_SUPER;
 	dwc->gadget.speed		= USB_SPEED_UNKNOWN;
 	dwc->gadget.sg_supported	= true;
 	dwc->gadget.name		= "dwc3-gadget";
 
+	/*
+	 * FIXME We might be setting max_speed to <SUPER, however versions
+	 * <2.20a of dwc3 have an issue with metastability (documented
+	 * elsewhere in this driver) which tells us we can't set max speed to
+	 * anything lower than SUPER.
+	 *
+	 * Because gadget.max_speed is only used by composite.c and function
+	 * drivers (i.e. it won't go into dwc3's registers) we are allowing this
+	 * to happen so we avoid sending SuperSpeed Capability descriptor
+	 * together with our BOS descriptor as that could confuse host into
+	 * thinking we can handle super speed.
+	 *
+	 * Note that, in fact, we won't even support GetBOS requests when speed
+	 * is less than super speed because we don't have means, yet, to tell
+	 * composite.c that we are USB 2.0 + LPM ECN.
+	 */
+	if (dwc->revision < DWC3_REVISION_220A)
+		dwc3_trace(trace_dwc3_gadget,
+				"Changing max_speed on rev %08x\n",
+				dwc->revision);
+
+	dwc->gadget.max_speed		= dwc->maximum_speed;
+
 	/*
 	 * Per databook, DWC3 needs buffer size to be aligned to MaxPacketSize
 	 * on ep out.

drivers/usb/gadget/function/f_loopback.c

@@ -329,7 +329,7 @@ static int alloc_requests(struct usb_composite_dev *cdev,
 	for (i = 0; i < loop->qlen && result == 0; i++) {
 		result = -ENOMEM;
 
-		in_req = usb_ep_alloc_request(loop->in_ep, GFP_KERNEL);
+		in_req = usb_ep_alloc_request(loop->in_ep, GFP_ATOMIC);
 		if (!in_req)
 			goto fail;
 

drivers/usb/gadget/udc/atmel_usba_udc.c

@@ -1633,7 +1633,7 @@ static irqreturn_t usba_udc_irq(int irq, void *devid)
 	spin_lock(&udc->lock);
 
 	int_enb = usba_int_enb_get(udc);
-	status = usba_readl(udc, INT_STA) & int_enb;
+	status = usba_readl(udc, INT_STA) & (int_enb | USBA_HIGH_SPEED);
 	DBG(DBG_INT, "irq, status=%#08x\n", status);
 
 	if (status & USBA_DET_SUSPEND) {

drivers/usb/musb/musb_core.c

@@ -132,7 +132,7 @@ static inline struct musb *dev_to_musb(struct device *dev)
 /*-------------------------------------------------------------------------*/
 
 #ifndef CONFIG_BLACKFIN
-static int musb_ulpi_read(struct usb_phy *phy, u32 offset)
+static int musb_ulpi_read(struct usb_phy *phy, u32 reg)
 {
 	void __iomem *addr = phy->io_priv;
 	int	i = 0;
@@ -151,7 +151,7 @@ static int musb_ulpi_read(struct usb_phy *phy, u32 offset)
 	 * ULPICarKitControlDisableUTMI after clearing POWER_SUSPENDM.
 	 */
 
-	musb_writeb(addr, MUSB_ULPI_REG_ADDR, (u8)offset);
+	musb_writeb(addr, MUSB_ULPI_REG_ADDR, (u8)reg);
 	musb_writeb(addr, MUSB_ULPI_REG_CONTROL,
 			MUSB_ULPI_REG_REQ | MUSB_ULPI_RDN_WR);
 
@@ -176,7 +176,7 @@ static int musb_ulpi_read(struct usb_phy *phy, u32 offset)
 	return ret;
 }
 
-static int musb_ulpi_write(struct usb_phy *phy, u32 offset, u32 data)
+static int musb_ulpi_write(struct usb_phy *phy, u32 val, u32 reg)
 {
 	void __iomem *addr = phy->io_priv;
 	int	i = 0;
@@ -191,8 +191,8 @@ static int musb_ulpi_write(struct usb_phy *phy, u32 offset, u32 data)
 	power &= ~MUSB_POWER_SUSPENDM;
 	musb_writeb(addr, MUSB_POWER, power);
 
-	musb_writeb(addr, MUSB_ULPI_REG_ADDR, (u8)offset);
-	musb_writeb(addr, MUSB_ULPI_REG_DATA, (u8)data);
+	musb_writeb(addr, MUSB_ULPI_REG_ADDR, (u8)reg);
+	musb_writeb(addr, MUSB_ULPI_REG_DATA, (u8)val);
 	musb_writeb(addr, MUSB_ULPI_REG_CONTROL, MUSB_ULPI_REG_REQ);
 
 	while (!(musb_readb(addr, MUSB_ULPI_REG_CONTROL)
@@ -1668,7 +1668,7 @@ EXPORT_SYMBOL_GPL(musb_interrupt);
 static bool use_dma = 1;
 
 /* "modprobe ... use_dma=0" etc */
-module_param(use_dma, bool, 0);
+module_param(use_dma, bool, 0644);
 MODULE_PARM_DESC(use_dma, "enable/disable use of DMA");
 
 void musb_dma_completion(struct musb *musb, u8 epnum, u8 transmit)

drivers/usb/musb/musb_host.c

@@ -112,22 +112,32 @@ static void musb_h_tx_flush_fifo(struct musb_hw_ep *ep)
 	struct musb	*musb = ep->musb;
 	void __iomem	*epio = ep->regs;
 	u16		csr;
-	u16		lastcsr = 0;
 	int		retries = 1000;
 
 	csr = musb_readw(epio, MUSB_TXCSR);
 	while (csr & MUSB_TXCSR_FIFONOTEMPTY) {
-		if (csr != lastcsr)
-			dev_dbg(musb->controller, "Host TX FIFONOTEMPTY csr: %02x\n", csr);
-		lastcsr = csr;
 		csr |= MUSB_TXCSR_FLUSHFIFO | MUSB_TXCSR_TXPKTRDY;
 		musb_writew(epio, MUSB_TXCSR, csr);
 		csr = musb_readw(epio, MUSB_TXCSR);
-		if (WARN(retries-- < 1,
+
+		/*
+		 * FIXME: sometimes the tx fifo flush failed, it has been
+		 * observed during device disconnect on AM335x.
+		 *
+		 * To reproduce the issue, ensure tx urb(s) are queued when
+		 * unplug the usb device which is connected to AM335x usb
+		 * host port.
+		 *
+		 * I found using a usb-ethernet device and running iperf
+		 * (client on AM335x) has very high chance to trigger it.
+		 *
+		 * Better to turn on dev_dbg() in musb_cleanup_urb() with
+		 * CPPI enabled to see the issue when aborting the tx channel.
+		 */
+		if (dev_WARN_ONCE(musb->controller, retries-- < 1,
 				"Could not flush host TX%d fifo: csr: %04x\n",
 				ep->epnum, csr))
 			return;
-		mdelay(1);
 	}
 }
 

drivers/usb/phy/phy-mxs-usb.c

@@ -452,10 +452,13 @@ static int mxs_phy_probe(struct platform_device *pdev)
 	struct clk *clk;
 	struct mxs_phy *mxs_phy;
 	int ret;
-	const struct of_device_id *of_id =
-			of_match_device(mxs_phy_dt_ids, &pdev->dev);
+	const struct of_device_id *of_id;
 	struct device_node *np = pdev->dev.of_node;
 
+	of_id = of_match_device(mxs_phy_dt_ids, &pdev->dev);
+	if (!of_id)
+		return -ENODEV;
+
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	base = devm_ioremap_resource(&pdev->dev, res);
 	if (IS_ERR(base))

drivers/usb/phy/phy-omap-otg.c

@@ -105,7 +105,6 @@ static int omap_otg_probe(struct platform_device *pdev)
 	extcon = extcon_get_extcon_dev(config->extcon);
 	if (!extcon)
 		return -EPROBE_DEFER;
-	otg_dev->extcon = extcon;
 
 	otg_dev = devm_kzalloc(&pdev->dev, sizeof(*otg_dev), GFP_KERNEL);
 	if (!otg_dev)
@@ -115,6 +114,7 @@ static int omap_otg_probe(struct platform_device *pdev)
 	if (IS_ERR(otg_dev->base))
 		return PTR_ERR(otg_dev->base);
 
+	otg_dev->extcon = extcon;
 	otg_dev->id_nb.notifier_call = omap_otg_id_notifier;
 	otg_dev->vbus_nb.notifier_call = omap_otg_vbus_notifier;